3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLT8365EMSE#PBF
Analog Devices · DC-DC Converters · MSOP-12
LT8365EMSE#PBF from Analog Devices, in a MSOP-12. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN/UVLO | input | Shutdown and undervoltage detect pin: the part stops switching below the 1.6V threshold, resumes above 1.68V with 80mV hysteresis, and VIN current drops below 1µA when the pin is below 0.2V. |
| 3 | VIN | power_in | Input supply pin for the 2.8V to 60V operating range, which must be locally bypassed with the input capacitor placed as close as possible to the pin. |
| 5 | INTVCC | power_out | Regulated 3.8V internal supply that must be bypassed with a 1µF low ESR ceramic capacitor to GND and must not be externally loaded or driven. |
| 6 | NC | unconnected | No internal connection; leave this pin open. |
| 7 | BIAS | input | Second input supply for powering INTVCC when 4.4V ≤ BIAS ≤ VIN, which reduces VIN current; tie to GND if unused. |
| 8 | VC | output | Error amplifier output pin to which the external compensation network is tied. |
| 9 | FBX | input | Voltage regulation feedback pin for positive or negative outputs, connected through a resistor divider to set the 1.6V (boost/SEPIC) or -0.8V (inverting) regulation level. |
| 10 | RT | passive | A resistor from this pin to the exposed pad GND programs the switching frequency over the 100kHz to 500kHz range. |
| 11 | SS | passive | Soft-start pin with a capacitor to GND that controls the inductor current ramp at start-up; charged at 2µA and discharged by an internal 220Ω MOSFET during shutdown or fault. |
| 12 | SYNC/MODE | input | Selects the operating mode (Burst, pulse-skipping, or SSFM) or synchronizes to an external clock, with GND or <0.14V selecting Burst mode. |
| 14 | SW2 | output | Output of the internal power switch, rated 150V and 1.5A, where the connected metal trace area should be minimized to reduce EMI. |
| 16 | SW1 | output | Output of the internal power switch, rated 150V and 1.5A, where the connected metal trace area should be minimized to reduce EMI. |
| 17 | PGND, GND | power_in | Exposed pad serving as power and signal ground that must be soldered to a continuous copper ground plane to conduct heat out of the package. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-12 |
| Category | Power Management (PMIC) |
| Pins | 13 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Voltage Range | VIN | 2.8 | 60 | V | 3 | ||
| VIN Quiescent Current at Shutdown | IQ | 1 | 2 | μA | VEN/UVLO = 0.2V | 3 | |
| VIN Quiescent Current at Shutdown (full operating temperature range) | IQ | 1 | 15 | μA | VEN/UVLO = 0.2V; l (full operating temperature range) | 3 | |
| VIN Quiescent Current at Shutdown | IQ | 2 | 5 | μA | VEN/UVLO = 1.5V | 3 | |
| VIN Quiescent Current at Shutdown (full operating temperature range) | IQ | 2 | 25 | μA | VEN/UVLO = 1.5V; l (full operating temperature range) | 3 | |
| VIN Quiescent Current Sleep Mode (Not Switching) | IQ | 9 | 15 | μA | Sleep Mode (Not Switching) SYNC = 0V | 3 | |
| VIN Quiescent Current Sleep Mode (Not Switching), full operating temperature range | IQ | 9 | 30 | μA | Sleep Mode (Not Switching) SYNC = 0V; l (full operating temperature range) | 3 | |
| VIN Quiescent Current Active Mode (Not Switching) | IQ | 1200 | 1600 | μA | Active Mode (Not Switching) SYNC = 0V or INTVCC, BIAS = 0V | 3 | |
| VIN Quiescent Current Active Mode (Not Switching), full operating temperature range | IQ | 1200 | 1850 | μA | Active Mode (Not Switching) SYNC = 0V or INTVCC, BIAS = 0V; l (full operating temperature range) | 3 | |
| VIN Quiescent Current Active Mode (Not Switching) | IQ | 22 | 40 | μA | SYNC = 0V or INTVCC, BIAS = 5V | 3 | |
| VIN Quiescent Current Active Mode (Not Switching), full operating temperature range | IQ | 22 | 65 | μA | SYNC = 0V or INTVCC, BIAS = 5V; l (full operating temperature range) | 3 | |
| BIAS Threshold Rising, BIAS Can Supply INTVCC | 4.4 | 4.65 | V | BIAS Threshold Rising, BIAS Can Supply INTVCC | 3 | ||
| BIAS Threshold Falling, BIAS Cannot Supply INTVCC | 4 | 4.25 | V | BIAS Threshold Falling, BIAS Cannot Supply INTVCC | 3 | ||
| FBX Regulation Voltage | FBX | 1.568 | 1.6 | 1.636 | V | FBX > 0V; l | 3 |
| FBX Regulation Voltage | FBX | -0.822 | -0.8 | -0.78 | V | FBX < 0V; l | 3 |
| FBX Line Regulation | 0.005 | 0.015 | %/V | FBX > 0V, 2.8V < VIN < 60V | 3 | ||
| FBX Pin Current | IFBX | -10 | 10 | nA | FBX = 1.6V, -0.8V; l | 3 | |
| Switching Frequency (fOSC) | fOSC | 92 | 100 | 113 | kHz | RT = 432k; l | 3 |
| Switching Frequency (fOSC) | fOSC | 279 | 300 | 321 | kHz | RT = 143k; l | 3 |
| Switching Frequency (fOSC) | fOSC | 465 | 500 | 535 | kHz | RT = 84.5k; l | 3 |
| SSFM Maximum Frequency Deviation | (Δf/fOSC) | 14 | 20 | 28 | % | (∆f/fOSC) • 100, RT = 143k | 3 |
| Minimum On-Time Burst Mode | 110 | 200 | ns | Burst Mode, VIN = 24V (Note 6) | 3 | ||
| Minimum On-Time Pulse-Skipping Mode | 110 | 200 | ns | Pulse-Skipping Mode, VIN = 24V (Note 6) | 3 | ||
| Minimum Off-Time | 100 | 115 | ns | l | 3 | ||
| SYNC/Mode Threshold High (Rising) | 1.3 | 1.7 | V | High (Rising), VIN = 24V; l | 3 | ||
| SYNC/Mode Threshold Low (Falling) | 0.14 | 0.2 | V | Low (Falling), VIN = 24V; l | 3 | ||
| SYNC/Clock Threshold Rising | 0.4 | 0.8 | V | Rising, VIN = 24V; l | 3 | ||
| SYNC/Clock Threshold Falling | 1.3 | 1.7 | V | Falling, VIN = 24V; l | 3 | ||
| fSYNC/fOSC Allowed Ratio | fSYNC/fOSC | 0.95 | 1 | 1.25 | kHz/kHz | RT = 84.5k | 3 |
| SYNC Pin Current | ISYNC | 10 | 25 | µA | SYNC = 2V | 3 | |
| Maximum Switch Current Limit Threshold | 1.5 | 2 | 2.7 | A | l | 3 | |
| Switch Leakage Current | ISW | 0.1 | 1 | µA | VSW = 150V | 3 | |
| EN/UVLO Pin Threshold (Rising) | VEN/UVLO | 1.576 | 1.68 | 1.9 | V | Start Switching; l | 4 |
| EN/UVLO Pin Threshold (Falling) | VEN/UVLO | 1.545 | 1.6 | 1.645 | V | Stop Switching; l | 4 |
| EN/UVLO Pin Current | IEN/UVLO | -50 | 50 | nA | VEN/UVLO = 1.6V; l | 4 | |
| Absolute Maximum SW Pin Voltage | SW | 150 | V | 2 | |||
| Absolute Maximum VIN, EN/UVLO Pin Voltage | VIN, EN/UVLO | 60 | V | 2 | |||
| Absolute Maximum BIAS Pin Voltage | BIAS | 60 | V | 2 | |||
| Absolute Maximum EN/UVLO Pin Above VIN Pin, SYNC | EN/UVLO, SYNC | 6 | V | EN/UVLO Pin Above VIN Pin, SYNC | 2 | ||
| Absolute Maximum VC Pin Voltage | VC | 4 | V | 2 | |||
| Absolute Maximum FBX Pin Voltage | FBX | -4 | 4 | V | ±4V | 2 | |
| Operating Junction Temperature LT8365E | TJ | -40 | 125 | °C | LT8365E (Note 3) | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 45 | °C/W | MSE package | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 10 | °C/W | MSE package | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | close as possible to the VIN pin, and the negative terminal as close as possible to the exposed pad PGND copper | 7 |
CAD (KiCad official)
- Symbol:
LT8365EMSE#PBF - Footprint:
Package_SO:Analog_MSOP-12-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-12 (KiCad packages3D, STEP)
- 3D model files:
lt8365emse-etched.step/lt8365emse-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8365emse.step/lt8365emse.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
c511973eed4b53a9, retrieved 2026-11-16, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).