Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ADC0804LCWMX

Texas Instruments · Pre-ordered Chips · SOIC-20-300mil

ADC0804LCWMX from Texas Instruments, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS input Active-low chip select; CS and WR must be low together to start a conversion, and CS and RD both low enable the data outputs.
2 RD input Active-low read strobe that, with CS low, enables the tri-state output latches and resets INTR.
3 WR input Active-low write strobe whose low-to-high transition (with CS low) starts a conversion, and the converter stays in reset while CS and WR are held low.
4 CLK IN input Schmitt-trigger clock input for an external clock (100 kHz to 1460 kHz, 40% to 60% duty cycle) or for an external RC network that sets the internal clock.
5 INTR output Active-low interrupt request that goes high-to-low when a conversion completes and is reset by a read (CS and RD low) at least 8 clock periods after assertion.
6 VIN(+) power_in Non-inverting differential analog input, which must stay within GND - 0.05 V to VCC + 0.05 V.
7 VIN(-) power_in Inverting differential analog input used to offset the zero level; if VIN(-) is greater than or equal to VIN(+) the output code is 0000 0000.
8 A GND power_in Analog ground pin, which should always be wired to the D GND point.
9 VREF/2 power_in Reference voltage input for full-scale adjustment, with an internal gain of 2 so the full-scale differential input is twice this voltage.
10 D GND power_in Digital ground pin, to which the supply bypass capacitor and any self-clocking capacitor should be returned.
11 DB7 tri_state Tri-state latched data output bit 7 (MSB), valid when CS and RD are both low.
12 DB6 tri_state Tri-state latched data output bit 6, valid when CS and RD are both low.
13 DB5 tri_state Tri-state latched data output bit 5, valid when CS and RD are both low.
14 DB4 tri_state Tri-state latched data output bit 4, valid when CS and RD are both low.
15 DB3 tri_state Tri-state latched data output bit 3, valid when CS and RD are both low.
16 DB2 tri_state Tri-state latched data output bit 2, valid when CS and RD are both low.
17 DB1 tri_state Tri-state latched data output bit 1, valid when CS and RD are both low.
18 DB0 (LSB) tri_state Tri-state latched data output bit 0 (LSB), valid when CS and RD are both low.
19 CLK R input RC timing resistor input for the internal clock generator; heavy capacitive or DC loading of this pin should be avoided.
20 VCC (or VREF) power_in +5 V supply voltage, which also serves as the upper reference input to the ladder.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-20-300mil
Category Interface ICs
Pins 20

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage (VCC) absolute maximum VCC 6.5 V 4
Logic control inputs voltage -0.3 18 V Logic control inputs 4
Voltage at other inputs and outputs -0.3 V 4
Lead temperature, surface mount package vapor phase 215 °C Vapor phase (60 seconds) 4
Lead temperature, surface mount package infrared 220 °C Infrared (15 seconds) 4
Storage temperature -65 150 °C 4
Package dissipation at TA = 25°C 875 mW TA = 25°C 4
Supply voltage (VCC) recommended VCC 4.5 5 5.5 V 4
Analog input voltage (recommended) -0.05 V 4
Operating free-air temperature range (ADC0804LCWM) 0 70 °C 5
Range of VCC (operating rating) VCC 4.5 6.3 V 5
Total Unadjusted Error (ADC0804) -1 1 LSB VREF/2 = 2.500 VDC 5
VREF/2 Input Resistance (ADC0804) 0.75 1.1 kΩ 5
Analog Input Voltage Range V(+) or V(-) -0.05 V 5
Conversion time (fCLK = 640 kHz) TC 103 114 µs fCLK = 640 kHz 5
Conversion time (in clock periods) TC 66 73 1/fCLK See (2) 5
Clock frequency fCLK 100 640 1460 kHz VCC = 5V 5
Clock duty cycle 40 60 % 5
Conversion rate in free-running mode CR 8770 9708 conv/s INTR tied to WR with CS = 0 VDC; fCLK = 640 kHz 5
Width of WR input (start pulse width) tW(WR) 100 ns CS = 0 VDC 6
Access time (delay from falling edge of RD to output data valid) tACC 135 200 ns CL = 100 pF 6
Tri-state control (delay from rising edge of RD to Hi-Z state) t1H, t0H 125 200 ns CL = 10 pF, RL = 10k 6
Delay from falling edge of WR or RD to reset of INTR tWI, tRI 300 450 ns 6
Input capacitance of logic control inputs CIN 5 7.5 pF 6
Tri-state output capacitance (data buffers) COUT 5 7.5 pF 6
Logical 1 input voltage (except pin 4 CLK IN) VIN(1) 2 15 VDC VCC = 5.25 VDC 6
Logical 0 input voltage (except pin 4 CLK IN) VIN(0) 0.8 VDC VCC = 4.75 VDC 6
Logical 1 input current (all inputs) IIN(1) 0.005 1 µADC VIN = 5 VDC 6
Logical 0 input current (all inputs) IIN(0) -1 -0.005 µADC VIN = 0 VDC 6
CLK IN (pin 4) positive going threshold voltage VT+ 2.7 3.1 3.5 VDC 6
CLK IN (pin 4) negative going threshold voltage VT− 1.5 1.8 2.1 VDC 6
CLK IN (pin 4) hysteresis (VT+)-(VT−) VH 0.6 1.3 2 VDC 6
Logical 0 CLK R output voltage VOUT 0.4 VDC IO = 360 µA, VCC = 4.75 VDC 6
Logical 1 CLK R output voltage VOUT 2.4 VDC IO = −360 µA, VCC = 4.75 VDC 6
Data outputs logical 0 output voltage VOUT(0) 0.4 VDC IOUT = 1.6 mA, VCC = 4.75 VDC 6
INTR output logical 0 output voltage VOUT(0) 0.4 VDC IOUT = 1.0 mA, VCC = 4.75 VDC 6
Data outputs and INTR logical 1 output voltage VOUT(1) 2.4 VDC IO = −360 µA, VCC = 4.75 VDC 6
Logical 1 output voltage (low-current) VOUT(1) 4.5 VDC IO = −10 µA, VCC = 4.75 VDC 6
Tri-state disabled output leakage (all data buffers) IOUT -3 µADC VOUT = 0 VDC 6
Tri-state disabled output leakage (all data buffers) IOUT 3 µADC VOUT = 5 VDC 6
Output short-circuit source current ISOURCE 4.5 6 mADC VOUT short to GND, TA = 25°C 6
Output short-circuit sink current ISINK 9 16 mADC VOUT short to VCC, TA = 25°C 6
Supply current (includes ladder current), ADC0804LCN/LCWM ICC 1.9 2.5 mA fCLK = 640 kHz, VREF/2 = NC, TA = 25°C and CS = 5 V 6
Junction-to-ambient thermal resistance (DW SOIC-20) RθJA 63.8 °C/W 4
Junction-to-case (top) thermal resistance (DW SOIC-20) RθJC(top) 27.2 °C/W 4
Junction-to-board thermal resistance (DW SOIC-20) RθJB 31.8 °C/W 4
Junction-to-top characterization parameter (DW SOIC-20) ψJT 5.7 °C/W 4
Junction-to-board characterization parameter (DW SOIC-20) ψJB 31.3 °C/W 4

CAD (KiCad official)

  • Symbol: ADC0804LCWMX
  • Footprint: Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm
  • 3D model: SOIC-20-300mil (KiCad packages3D, STEP)
  • 3D model files: adc0804lcwmx-etched.step / adc0804lcwmx-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); adc0804lcwmx.step / adc0804lcwmx.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (58 pp, sha256 44bd9e8071ef6612, retrieved 2026-11-17)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF