Generated by kicad-footprint-generator · KiCad file format 20260206
ADC0804LCWMX
Texas Instruments · Pre-ordered Chips · SOIC-20-300mil
ADC0804LCWMX from Texas Instruments, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Active-low chip select; CS and WR must be low together to start a conversion, and CS and RD both low enable the data outputs. |
| 2 | RD | input | Active-low read strobe that, with CS low, enables the tri-state output latches and resets INTR. |
| 3 | WR | input | Active-low write strobe whose low-to-high transition (with CS low) starts a conversion, and the converter stays in reset while CS and WR are held low. |
| 4 | CLK IN | input | Schmitt-trigger clock input for an external clock (100 kHz to 1460 kHz, 40% to 60% duty cycle) or for an external RC network that sets the internal clock. |
| 5 | INTR | output | Active-low interrupt request that goes high-to-low when a conversion completes and is reset by a read (CS and RD low) at least 8 clock periods after assertion. |
| 6 | VIN(+) | power_in | Non-inverting differential analog input, which must stay within GND - 0.05 V to VCC + 0.05 V. |
| 7 | VIN(-) | power_in | Inverting differential analog input used to offset the zero level; if VIN(-) is greater than or equal to VIN(+) the output code is 0000 0000. |
| 8 | A GND | power_in | Analog ground pin, which should always be wired to the D GND point. |
| 9 | VREF/2 | power_in | Reference voltage input for full-scale adjustment, with an internal gain of 2 so the full-scale differential input is twice this voltage. |
| 10 | D GND | power_in | Digital ground pin, to which the supply bypass capacitor and any self-clocking capacitor should be returned. |
| 11 | DB7 | tri_state | Tri-state latched data output bit 7 (MSB), valid when CS and RD are both low. |
| 12 | DB6 | tri_state | Tri-state latched data output bit 6, valid when CS and RD are both low. |
| 13 | DB5 | tri_state | Tri-state latched data output bit 5, valid when CS and RD are both low. |
| 14 | DB4 | tri_state | Tri-state latched data output bit 4, valid when CS and RD are both low. |
| 15 | DB3 | tri_state | Tri-state latched data output bit 3, valid when CS and RD are both low. |
| 16 | DB2 | tri_state | Tri-state latched data output bit 2, valid when CS and RD are both low. |
| 17 | DB1 | tri_state | Tri-state latched data output bit 1, valid when CS and RD are both low. |
| 18 | DB0 (LSB) | tri_state | Tri-state latched data output bit 0 (LSB), valid when CS and RD are both low. |
| 19 | CLK R | input | RC timing resistor input for the internal clock generator; heavy capacitive or DC loading of this pin should be avoided. |
| 20 | VCC (or VREF) | power_in | +5 V supply voltage, which also serves as the upper reference input to the ladder. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-20-300mil |
| Category | Interface ICs |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (VCC) absolute maximum | VCC | 6.5 | V | 4 | |||
| Logic control inputs voltage | -0.3 | 18 | V | Logic control inputs | 4 | ||
| Voltage at other inputs and outputs | -0.3 | V | 4 | ||||
| Lead temperature, surface mount package vapor phase | 215 | °C | Vapor phase (60 seconds) | 4 | |||
| Lead temperature, surface mount package infrared | 220 | °C | Infrared (15 seconds) | 4 | |||
| Storage temperature | -65 | 150 | °C | 4 | |||
| Package dissipation at TA = 25°C | 875 | mW | TA = 25°C | 4 | |||
| Supply voltage (VCC) recommended | VCC | 4.5 | 5 | 5.5 | V | 4 | |
| Analog input voltage (recommended) | -0.05 | V | 4 | ||||
| Operating free-air temperature range (ADC0804LCWM) | 0 | 70 | °C | 5 | |||
| Range of VCC (operating rating) | VCC | 4.5 | 6.3 | V | 5 | ||
| Total Unadjusted Error (ADC0804) | -1 | 1 | LSB | VREF/2 = 2.500 VDC | 5 | ||
| VREF/2 Input Resistance (ADC0804) | 0.75 | 1.1 | kΩ | 5 | |||
| Analog Input Voltage Range V(+) or V(-) | -0.05 | V | 5 | ||||
| Conversion time (fCLK = 640 kHz) | TC | 103 | 114 | µs | fCLK = 640 kHz | 5 | |
| Conversion time (in clock periods) | TC | 66 | 73 | 1/fCLK | See (2) | 5 | |
| Clock frequency | fCLK | 100 | 640 | 1460 | kHz | VCC = 5V | 5 |
| Clock duty cycle | 40 | 60 | % | 5 | |||
| Conversion rate in free-running mode | CR | 8770 | 9708 | conv/s | INTR tied to WR with CS = 0 VDC; fCLK = 640 kHz | 5 | |
| Width of WR input (start pulse width) | tW(WR) | 100 | ns | CS = 0 VDC | 6 | ||
| Access time (delay from falling edge of RD to output data valid) | tACC | 135 | 200 | ns | CL = 100 pF | 6 | |
| Tri-state control (delay from rising edge of RD to Hi-Z state) | t1H, t0H | 125 | 200 | ns | CL = 10 pF, RL = 10k | 6 | |
| Delay from falling edge of WR or RD to reset of INTR | tWI, tRI | 300 | 450 | ns | 6 | ||
| Input capacitance of logic control inputs | CIN | 5 | 7.5 | pF | 6 | ||
| Tri-state output capacitance (data buffers) | COUT | 5 | 7.5 | pF | 6 | ||
| Logical 1 input voltage (except pin 4 CLK IN) | VIN(1) | 2 | 15 | VDC | VCC = 5.25 VDC | 6 | |
| Logical 0 input voltage (except pin 4 CLK IN) | VIN(0) | 0.8 | VDC | VCC = 4.75 VDC | 6 | ||
| Logical 1 input current (all inputs) | IIN(1) | 0.005 | 1 | µADC | VIN = 5 VDC | 6 | |
| Logical 0 input current (all inputs) | IIN(0) | -1 | -0.005 | µADC | VIN = 0 VDC | 6 | |
| CLK IN (pin 4) positive going threshold voltage | VT+ | 2.7 | 3.1 | 3.5 | VDC | 6 | |
| CLK IN (pin 4) negative going threshold voltage | VT− | 1.5 | 1.8 | 2.1 | VDC | 6 | |
| CLK IN (pin 4) hysteresis (VT+)-(VT−) | VH | 0.6 | 1.3 | 2 | VDC | 6 | |
| Logical 0 CLK R output voltage | VOUT | 0.4 | VDC | IO = 360 µA, VCC = 4.75 VDC | 6 | ||
| Logical 1 CLK R output voltage | VOUT | 2.4 | VDC | IO = −360 µA, VCC = 4.75 VDC | 6 | ||
| Data outputs logical 0 output voltage | VOUT(0) | 0.4 | VDC | IOUT = 1.6 mA, VCC = 4.75 VDC | 6 | ||
| INTR output logical 0 output voltage | VOUT(0) | 0.4 | VDC | IOUT = 1.0 mA, VCC = 4.75 VDC | 6 | ||
| Data outputs and INTR logical 1 output voltage | VOUT(1) | 2.4 | VDC | IO = −360 µA, VCC = 4.75 VDC | 6 | ||
| Logical 1 output voltage (low-current) | VOUT(1) | 4.5 | VDC | IO = −10 µA, VCC = 4.75 VDC | 6 | ||
| Tri-state disabled output leakage (all data buffers) | IOUT | -3 | µADC | VOUT = 0 VDC | 6 | ||
| Tri-state disabled output leakage (all data buffers) | IOUT | 3 | µADC | VOUT = 5 VDC | 6 | ||
| Output short-circuit source current | ISOURCE | 4.5 | 6 | mADC | VOUT short to GND, TA = 25°C | 6 | |
| Output short-circuit sink current | ISINK | 9 | 16 | mADC | VOUT short to VCC, TA = 25°C | 6 | |
| Supply current (includes ladder current), ADC0804LCN/LCWM | ICC | 1.9 | 2.5 | mA | fCLK = 640 kHz, VREF/2 = NC, TA = 25°C and CS = 5 V | 6 | |
| Junction-to-ambient thermal resistance (DW SOIC-20) | RθJA | 63.8 | °C/W | 4 | |||
| Junction-to-case (top) thermal resistance (DW SOIC-20) | RθJC(top) | 27.2 | °C/W | 4 | |||
| Junction-to-board thermal resistance (DW SOIC-20) | RθJB | 31.8 | °C/W | 4 | |||
| Junction-to-top characterization parameter (DW SOIC-20) | ψJT | 5.7 | °C/W | 4 | |||
| Junction-to-board characterization parameter (DW SOIC-20) | ψJB | 31.3 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
ADC0804LCWMX - Footprint:
Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm - 3D model: SOIC-20-300mil (KiCad packages3D, STEP)
- 3D model files:
adc0804lcwmx-etched.step/adc0804lcwmx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);adc0804lcwmx.step/adc0804lcwmx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (58 pp, sha256
44bd9e8071ef6612, retrieved 2026-11-17) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).