Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ISL1209IU10Z

RENESAS · Real-time Clocks (RTC) · MSOP-10

ISL1209IU10Z from RENESAS, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 X1 input Input of the inverting amplifier for the external 32.768kHz crystal, which can also be driven directly from a 32.768kHz source.
2 X2 output Output of the inverting amplifier for the 32.768kHz crystal, which should be left open when X1 is driven from an external source.
3 VBAT power_in Backup supply input that powers the device when VDD fails, specified at 1.8 V to 5.5 V in the DC characteristics, and tied to ground if not used.
4 GND power_in Ground reference for the device.
5 EVIN input Event input that detects an externally monitored event when a high signal is present, with VIH of 0.7 x VDD min and VIL of 0.3 x VDD max.
6 EVDET output Open-drain event detect output that goes low when an event is detected at EVIN and stays low until the EVT bit is cleared.
7 SDA bidirectional Open-drain I2C serial data line that requires a pull-up resistor, is designed for 400kHz operation, and is disabled when the VBAT backup supply is active.
8 SCL input I2C serial clock input that clocks all serial data into and out of the device; its input buffer is always active except when VBAT backup is active.
9 IRQ/FOUT output Multi-function open-drain active-low output that operates as an interrupt (IRQ) or frequency output (FOUT), selected via the control/status register.
10 VDD power_in Main power supply input operating from 2.7 V to 5.5 V, with a 0.1 µF capacitor recommended from VDD to ground.

Key specifications

Parameter Value
Manufacturer RENESAS
Package MSOP-10
Category Clock and Timing
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD Main Power Supply VDD 2.7 5.5 V 3
VBAT Battery Supply Voltage VBAT 1.8 5.5 V 3
Operating temperature range -40 85 °C Ordering information TEMP RANGE 1
Voltage on VDD, VBAT, SCL, SDA, IRQ pins (respect to ground) -0.5 7 V Respect to ground 3
Storage Temperature -65 150 °C 3
Lead Temperature (Soldering) 300 °C Soldering, 10s 3
Supply Current IDD1 IDD1 2 6 µA VDD = 5V 3
Supply Current IDD1 IDD1 1.2 4 µA VDD = 3V 3
Supply Current With I2C Active IDD2 40 120 µA VDD = 5V 3
Supply Current (Low Power Mode) IDD3 1.4 5 µA VDD = 5V, LPMODE = 1 3
Battery Supply Current IBAT 400 950 nA VBAT = 3V 3
Input Leakage Current on SCL ILI 100 nA 3
I/O Leakage Current on SDA ILO 100 nA 3
VBAT Mode Threshold VTRIP 1.6 2.2 2.6 V 3
VTRIP Hysteresis VTRIPHYS 10 30 60 mV 3
VBAT Hysteresis VBATHYS 15 50 100 mV 3
EVIN input low voltage VIL -0.3 V 3
EVIN Pullup Current IEVPU 1.5 µA VSUP = 3V 3
IRQ/FOUT and EVDET Output Low Voltage VOL 0.4 V VDD = 5V, IOL = 3mA 3
VDD Negative Slew rate VDD SR- 10 V/ms 3
SDA output buffer LOW voltage VOL 0.4 V VDD = 5V, IOL = 3mA 4
SDA and SCL pin capacitance Cpin 10 pF TA = +25°C, f = 1MHz, VDD = 5V, VIN = 0V, VOUT = 0V 4
SCL frequency fSCL 400 kHz 4
Pulse width suppression time at SDA and SCL inputs tIN 50 ns 4
SCL falling edge to SDA output data valid tAA 900 ns SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window 4
Time the bus must be free before the start of a new transmission tBUF 1300 ns SDA crossing 70% of VDD during a STOP condition, to SDA crossing 70% of VDD during the following START condition 4
Clock LOW time tLOW 1300 ns Measured at the 30% of VDD crossing 4
Clock HIGH time tHIGH 600 ns Measured at the 70% of VDD crossing 4
START condition setup time tSU:STA 600 ns SCL rising edge to SDA falling edge. Both crossing 70% of VDD 4
START condition hold time tHD:STA 600 ns From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD 4
Input data setup time tSU:DAT 100 ns From SDA exiting the 30% to 70% of VDD window, to SCL rising edge crossing 30% of VDD 4
Input data hold time tHD:DAT 20 900 ns From SCL falling edge crossing 30% of VDD to SDA entering the 30% to 70% of VDD window 4
STOP condition setup time tSU:STO 600 ns From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD 4
STOP condition hold time tHD:STO 600 ns From SDA rising edge to SCL falling edge. Both crossing 70% of VDD 4
Output data hold time tDH 0 ns From SCL falling edge crossing 30% of VDD, until SDA enters the 30% to 70% of VDD window 4
SDA and SCL rise time tR 300 ns From 30% to 70% of VDD 4
SDA and SCL fall time tF 300 ns From 70% to 30% of VDD 4
Capacitive loading of SDA or SCL Cb 10 400 pF Total on-chip and off-chip 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing Abs ESD Rating (Human Body Model). . . . . . . . . . . . . . . . . . . . . .>±2kV CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a str 3

CAD (KiCad official)

  • Symbol: ISL1209IU10Z
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: isl1209iu10z-etched.step / isl1209iu10z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl1209iu10z.step / isl1209iu10z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (25 pp, sha256 83ff3be0086bf18f, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF