Generated by kicad-footprint-generator · KiCad file format 20260206
ISL1209IU10Z
RENESAS · Real-time Clocks (RTC) · MSOP-10
ISL1209IU10Z from RENESAS, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Input of the inverting amplifier for the external 32.768kHz crystal, which can also be driven directly from a 32.768kHz source. |
| 2 | X2 | output | Output of the inverting amplifier for the 32.768kHz crystal, which should be left open when X1 is driven from an external source. |
| 3 | VBAT | power_in | Backup supply input that powers the device when VDD fails, specified at 1.8 V to 5.5 V in the DC characteristics, and tied to ground if not used. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | EVIN | input | Event input that detects an externally monitored event when a high signal is present, with VIH of 0.7 x VDD min and VIL of 0.3 x VDD max. |
| 6 | EVDET | output | Open-drain event detect output that goes low when an event is detected at EVIN and stays low until the EVT bit is cleared. |
| 7 | SDA | bidirectional | Open-drain I2C serial data line that requires a pull-up resistor, is designed for 400kHz operation, and is disabled when the VBAT backup supply is active. |
| 8 | SCL | input | I2C serial clock input that clocks all serial data into and out of the device; its input buffer is always active except when VBAT backup is active. |
| 9 | IRQ/FOUT | output | Multi-function open-drain active-low output that operates as an interrupt (IRQ) or frequency output (FOUT), selected via the control/status register. |
| 10 | VDD | power_in | Main power supply input operating from 2.7 V to 5.5 V, with a 0.1 µF capacitor recommended from VDD to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | MSOP-10 |
| Category | Clock and Timing |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Main Power Supply | VDD | 2.7 | 5.5 | V | 3 | ||
| VBAT Battery Supply Voltage | VBAT | 1.8 | 5.5 | V | 3 | ||
| Operating temperature range | -40 | 85 | °C | Ordering information TEMP RANGE | 1 | ||
| Voltage on VDD, VBAT, SCL, SDA, IRQ pins (respect to ground) | -0.5 | 7 | V | Respect to ground | 3 | ||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Lead Temperature (Soldering) | 300 | °C | Soldering, 10s | 3 | |||
| Supply Current IDD1 | IDD1 | 2 | 6 | µA | VDD = 5V | 3 | |
| Supply Current IDD1 | IDD1 | 1.2 | 4 | µA | VDD = 3V | 3 | |
| Supply Current With I2C Active | IDD2 | 40 | 120 | µA | VDD = 5V | 3 | |
| Supply Current (Low Power Mode) | IDD3 | 1.4 | 5 | µA | VDD = 5V, LPMODE = 1 | 3 | |
| Battery Supply Current | IBAT | 400 | 950 | nA | VBAT = 3V | 3 | |
| Input Leakage Current on SCL | ILI | 100 | nA | 3 | |||
| I/O Leakage Current on SDA | ILO | 100 | nA | 3 | |||
| VBAT Mode Threshold | VTRIP | 1.6 | 2.2 | 2.6 | V | 3 | |
| VTRIP Hysteresis | VTRIPHYS | 10 | 30 | 60 | mV | 3 | |
| VBAT Hysteresis | VBATHYS | 15 | 50 | 100 | mV | 3 | |
| EVIN input low voltage | VIL | -0.3 | V | 3 | |||
| EVIN Pullup Current | IEVPU | 1.5 | µA | VSUP = 3V | 3 | ||
| IRQ/FOUT and EVDET Output Low Voltage | VOL | 0.4 | V | VDD = 5V, IOL = 3mA | 3 | ||
| VDD Negative Slew rate | VDD SR- | 10 | V/ms | 3 | |||
| SDA output buffer LOW voltage | VOL | 0.4 | V | VDD = 5V, IOL = 3mA | 4 | ||
| SDA and SCL pin capacitance | Cpin | 10 | pF | TA = +25°C, f = 1MHz, VDD = 5V, VIN = 0V, VOUT = 0V | 4 | ||
| SCL frequency | fSCL | 400 | kHz | 4 | |||
| Pulse width suppression time at SDA and SCL inputs | tIN | 50 | ns | 4 | |||
| SCL falling edge to SDA output data valid | tAA | 900 | ns | SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window | 4 | ||
| Time the bus must be free before the start of a new transmission | tBUF | 1300 | ns | SDA crossing 70% of VDD during a STOP condition, to SDA crossing 70% of VDD during the following START condition | 4 | ||
| Clock LOW time | tLOW | 1300 | ns | Measured at the 30% of VDD crossing | 4 | ||
| Clock HIGH time | tHIGH | 600 | ns | Measured at the 70% of VDD crossing | 4 | ||
| START condition setup time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge. Both crossing 70% of VDD | 4 | ||
| START condition hold time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD | 4 | ||
| Input data setup time | tSU:DAT | 100 | ns | From SDA exiting the 30% to 70% of VDD window, to SCL rising edge crossing 30% of VDD | 4 | ||
| Input data hold time | tHD:DAT | 20 | 900 | ns | From SCL falling edge crossing 30% of VDD to SDA entering the 30% to 70% of VDD window | 4 | |
| STOP condition setup time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD | 4 | ||
| STOP condition hold time | tHD:STO | 600 | ns | From SDA rising edge to SCL falling edge. Both crossing 70% of VDD | 4 | ||
| Output data hold time | tDH | 0 | ns | From SCL falling edge crossing 30% of VDD, until SDA enters the 30% to 70% of VDD window | 4 | ||
| SDA and SCL rise time | tR | 300 | ns | From 30% to 70% of VDD | 4 | ||
| SDA and SCL fall time | tF | 300 | ns | From 70% to 30% of VDD | 4 | ||
| Capacitive loading of SDA or SCL | Cb | 10 | 400 | pF | Total on-chip and off-chip | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | Abs | ESD Rating (Human Body Model). . . . . . . . . . . . . . . . . . . . . .>±2kV CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a str | 3 |
CAD (KiCad official)
- Symbol:
ISL1209IU10Z - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
isl1209iu10z-etched.step/isl1209iu10z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl1209iu10z.step/isl1209iu10z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (25 pp, sha256
83ff3be0086bf18f, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).