3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMSP430G2302IPW20R
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · TSSOP-20
MSP430G2302IPW20R from Texas Instruments, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DVCC | power_in | Supply voltage, 1.8 V to 3.6 V during program execution and 2.2 V to 3.6 V during flash programming/erase. |
| 2 | P1.0/TA0CLK/ACLK | bidirectional | General-purpose digital I/O that can also be the Timer0_A clock input TACLK or the ACLK signal output. |
| 3 | P1.1/TA0.0 | bidirectional | General-purpose digital I/O that can also be Timer0_A capture CCI0A input or compare Out0 output. |
| 4 | P1.2/TA0.1 | bidirectional | General-purpose digital I/O that can also be Timer0_A capture CCI1A input or compare Out1 output. |
| 5 | P1.3 | bidirectional | General-purpose digital I/O pin (the ADC10 functions on this pin are available only on MSP430G2x32, not on this device). |
| 6 | P1.4/TA0.2/SMCLK/TCK | bidirectional | General-purpose digital I/O that can also be Timer0_A CCI2A input or Out2 output, the SMCLK signal output, or the JTAG test clock TCK for programming and test. |
| 7 | P1.5/TA0.0/SCLK/TMS | bidirectional | General-purpose digital I/O that can also be Timer0_A Out0 output, the USI clock (input in I2C mode, in/output in SPI mode), or JTAG test mode select TMS. |
| 8 | P2.0 | bidirectional | General-purpose digital I/O pin; its pulldown resistor should be enabled by setting P2REN.0 = 1. |
| 9 | P2.1 | bidirectional | General-purpose digital I/O pin; its pulldown resistor should be enabled by setting P2REN.1 = 1. |
| 10 | P2.2 | bidirectional | General-purpose digital I/O pin; its pulldown resistor should be enabled by setting P2REN.2 = 1. |
| 11 | P2.3 | bidirectional | General-purpose digital I/O pin; its pulldown resistor should be enabled by setting P2REN.3 = 1. |
| 12 | P2.4 | bidirectional | General-purpose digital I/O pin; its pulldown resistor should be enabled by setting P2REN.4 = 1. |
| 13 | P2.5 | bidirectional | General-purpose digital I/O pin; its pulldown resistor should be enabled by setting P2REN.5 = 1. |
| 14 | P1.6/TA0.1/SDO/SCL/TDI/TCLK | bidirectional | General-purpose digital I/O that can also be Timer0_A Out1 output, USI SPI data output (SDO) or I2C clock (SCL), or JTAG test data input / test clock input TDI/TCLK. |
| 15 | P1.7/SDI/SDA/TDO/TDI | bidirectional | General-purpose digital I/O that can also be USI SPI data input (SDI) or I2C data (SDA), or JTAG test data output / test data input TDO/TDI. |
| 16 | RST/NMI/SBWTDIO | input | Reset input, nonmaskable interrupt input, and Spy-Bi-Wire test data input/output during programming and test. |
| 17 | TEST/SBWTCK | input | Selects test mode for the JTAG pins on Port 1 and is the Spy-Bi-Wire test clock input; the device protection fuse is connected to TEST. |
| 18 | XOUT/P2.7 | bidirectional | Crystal oscillator output terminal or general-purpose digital I/O; if used as an input, excess current flows until P2SEL.7 is cleared. |
| 19 | XIN/P2.6/TA0.1 | bidirectional | Crystal oscillator input terminal, general-purpose digital I/O, or Timer0_A Out1 output. |
| 20 | DVSS | power_in | Ground reference. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-20 |
| Category | Embedded Processors & Controllers |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage applied at VCC to VSS | -0.3 | 4.1 | V | 17 | |||
| Voltage applied to any pin (referenced to VSS) | -0.3 | V | Printed max is VCC + 0.3 V | 17 | |||
| Diode current at any device pin | -2 | 2 | mA | 17 | |||
| Storage temperature range | Tstg | -55 | 150 | °C | Unprogrammed device | 17 | |
| Supply voltage | VCC | 1.8 | 3.6 | V | During program execution | 17 | |
| Supply voltage | VCC | 2.2 | 3.6 | V | During flash programming/erase | 17 | |
| Operating free-air temperature | TA | -40 | 85 | °C | 17 | ||
| Processor frequency (maximum MCLK frequency) | fSYSTEM | 6 | MHz | VCC = 1.8 V, duty cycle 50% ± 10% | 17 | ||
| Processor frequency (maximum MCLK frequency) | fSYSTEM | 12 | MHz | VCC = 2.7 V, duty cycle 50% ± 10% | 17 | ||
| Processor frequency (maximum MCLK frequency) | fSYSTEM | 16 | MHz | VCC = 3.3 V, duty cycle 50% ± 10% | 17 | ||
| Positive-going input threshold voltage | VIT+ | 1.35 | 2.25 | V | VCC = 3 V | 20 | |
| Negative-going input threshold voltage | VIT- | 0.75 | 1.65 | V | VCC = 3 V | 20 | |
| Input voltage hysteresis (VIT+, VIT-) | Vhys | 0.3 | 1 | V | VCC = 3 V | 20 | |
| Pullup/pulldown resistor | RPull | 20 | 35 | 50 | kΩ | VCC = 3 V; for pullup VIN = VSS, for pulldown VIN = VCC | 20 |
| High-impedance leakage current | Ilkg(Px.x) | -50 | 50 | nA | VCC = 3 V | 20 | |
| RSELx supply voltage range | VCC | 1.8 | 3.6 | V | RSELx < 14 | 25 | |
| RSELx supply voltage range | VCC | 2.2 | 3.6 | V | RSELx = 14 | 25 | |
| RSELx supply voltage range | VCC | 3 | 3.6 | V | RSELx = 15 | 25 | |
| 1-MHz tolerance over temperature (calibrated at 30°C and 3 V) | -3 | 0.5 | 3 | % | BCSCTL1 = CALBC1_1MHZ, DCOCTL = CALDCO_1MHZ, 0°C to 85°C, VCC = 3 V | 26 | |
| 1-MHz tolerance over VCC (calibrated at 30°C and 3 V) | -3 | 2 | 3 | % | BCSCTL1 = CALBC1_1MHZ, DCOCTL = CALDCO_1MHZ, 30°C, VCC 1.8 V to 3.6 V | 26 | |
| 1-MHz tolerance overall (calibrated at 30°C and 3 V) | -6 | 3 | 6 | % | BCSCTL1 = CALBC1_1MHZ, DCOCTL = CALDCO_1MHZ, -40°C to 85°C, VCC 1.8 V to 3.6 V | 26 | |
| 8-MHz tolerance over temperature (calibrated at 30°C and 3 V) | -3 | 0.5 | 3 | % | BCSCTL1 = CALBC1_8MHZ, DCOCTL = CALDCO_8MHZ, 0°C to 85°C, VCC = 3 V | 26 | |
| 8-MHz tolerance over VCC (calibrated at 30°C and 3 V) | -3 | 2 | 3 | % | BCSCTL1 = CALBC1_8MHZ, DCOCTL = CALDCO_8MHZ, 30°C, VCC 2.2 V to 3.6 V | 26 | |
| 8-MHz tolerance overall (calibrated at 30°C and 3 V) | -6 | 3 | 6 | % | BCSCTL1 = CALBC1_8MHZ, DCOCTL = CALDCO_8MHZ, -40°C to 85°C, VCC 2.2 V to 3.6 V | 26 | |
| 12-MHz tolerance over temperature (calibrated at 30°C and 3 V) | -3 | 0.5 | 3 | % | BCSCTL1 = CALBC1_12MHZ, DCOCTL = CALDCO_12MHZ, 0°C to 85°C, VCC = 3 V | 26 | |
| 12-MHz tolerance over VCC (calibrated at 30°C and 3 V) | -3 | 2 | 3 | % | BCSCTL1 = CALBC1_12MHZ, DCOCTL = CALDCO_12MHZ, 30°C, VCC 2.7 V to 3.6 V | 26 | |
| 12-MHz tolerance overall (calibrated at 30°C and 3 V) | -6 | 3 | 6 | % | BCSCTL1 = CALBC1_12MHZ, DCOCTL = CALDCO_12MHZ, -40°C to 85°C, VCC 2.7 V to 3.6 V | 26 | |
| 16-MHz tolerance over temperature (calibrated at 30°C and 3 V) | -3 | 0.5 | 3 | % | BCSCTL1 = CALBC1_16MHZ, DCOCTL = CALDCO_16MHZ, 0°C to 85°C, VCC = 3.3 V | 26 | |
| 16-MHz tolerance over VCC (calibrated at 30°C and 3 V) | -3 | 2 | 3 | % | BCSCTL1 = CALBC1_16MHZ, DCOCTL = CALDCO_16MHZ, 30°C, VCC 3.3 V to 3.6 V | 26 | |
| 16-MHz tolerance overall (calibrated at 30°C and 3 V) | -6 | 3 | 6 | % | BCSCTL1 = CALBC1_16MHZ, DCOCTL = CALDCO_16MHZ, -40°C to 85°C, VCC 3.3 V to 3.6 V | 26 | |
| LFXT1 oscillator logic level square wave input frequency, LF mode | fLFXT1,LF,logic | 10000 | 32768 | 50000 | Hz | XTS = 0, XCAPx = 0, LFXT1Sx = 3, VCC 1.8 V to 3.6 V | 28 |
| Duty cycle, LF mode | 30 | 50 | 70 | % | XTS = 0, measured at P2.0/ACLK, fLFXT1,LF = 32768 Hz, VCC = 2.2 V | 28 | |
| Oscillator fault frequency, LF mode | fFault,LF | 10 | 10000 | Hz | XTS = 0, XCAPx = 0, LFXT1Sx = 3, VCC = 2.2 V | 28 | |
| VLO frequency | fVLO | 4 | 12 | 20 | kHz | -40°C to 85°C, VCC = 3 V | 28 |
CAD (KiCad official)
- Symbol:
MSP430G2302IPW20R - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files:
msp430g2302ipw20r-etched.step/msp430g2302ipw20r-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);msp430g2302ipw20r.step/msp430g2302ipw20r.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (77 pp, sha256
2f7249bd97fe2885, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).