3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownBMP388
Bosch Sensortec · Pressure Sensors · LGA-10(2x2)
BMP388 from Bosch Sensortec, in a LGA-10(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDDIO | power_in | Digital interface supply VDDIO, with a stated interface voltage range of 1.2 V to 3.6 V. |
| 2 | SCK | input | Serial clock input, connected to SCK in SPI modes and to SCL in I²C mode. |
| 3 | VSS | power_in | Ground connection to GND. |
| 4 | SDI | bidirectional | Serial data input in 4-wire SPI, shared SDI/SDO data line in 3-wire SPI, and SDA in I²C mode. |
| 5 | SDO | bidirectional | Serial data output in 4-wire SPI, not connected in 3-wire SPI, and SA0 I²C address select in I²C mode. |
| 6 | CSB | input | Chip select input, connected to CSB in SPI modes and to CSB in I²C mode, where it is recommended to drive VDDIO at power-on. |
| 7 | INT | output | Interrupt output to the host INT input, or left unconnected (DNC) in I²C mode; push-pull active high by default after power-on or soft reset. |
| 8 | VSS | power_in | Ground connection to GND. |
| 9 | VSS | power_in | Ground connection to GND. |
| 10 | VDD | power_in | Analog supply VDD, with a main supply voltage range of 1.65 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Bosch Sensortec |
| Package | LGA-10(2x2) |
| Category | Sensors |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating temperature range | TA | -40 | 25 | 85 | °C | operational | 7 |
| Operating temperature range, full accuracy | TA | 0 | 65 | °C | full accuracy | 7 | |
| Operating pressure range | P | 300 | 1250 | hPa | full accuracy | 7 | |
| Sensor supply voltage | VDD | 1.65 | 1.8 | 3.6 | V | ripple max. 50mVpp | 7 |
| Interface supply voltage | VDDIO | 1.2 | 1.8 | 3.6 | V | 7 | |
| Sleep current | IDD,sleep | 2 | µA | VDD = VDDIO 1.8-3.6 V | 7 | ||
| Peak current during pressure measurement | Ipeak | 700 | 800 | µA | during pressure measurement | 7 | |
| Current at temperature measurement | IDDT | 300 | 400 | µA | at temperature measurement | 7 | |
| Relative accuracy pressure | Arel | -0.082 | 0.082 | hPa | 900 … 1100 hPa, 25 . . . 40 °C | 7 | |
| Relative accuracy pressure | Arel | -66 | 66 | cm | 900 … 1100 hPa, 25 . . . 40 °C | 7 | |
| Offset temperature coefficient | TCO | -0.75 | 0.75 | Pa/K | 700-1100 hPa, 0 . . . 55 °C | 7 | |
| Offset temperature coefficient | TCO | -1 | 1 | Pa/K | 700-1100 hPa, -20 . . .0 °C | 7 | |
| Absolute accuracy pressure, full range | APfull | -0.5 | 0.5 | hPa | 300 . . 1100 hPa, -20 . . . 65 °C | 7 | |
| Absolute accuracy pressure, extended range | APext | -0.4 | 0.4 | hPa | 900 . . 1100 hPa, 25 . . . 40 °C | 7 | |
| Absolute accuracy pressure, 1100-1250 hPa | AP | -1.5 | 1.5 | hPa | 1100 . . 1250 hPa, 0 . . 65 °C | 8 | |
| Resolution of output data pressure | RP | 0.016 | Pa | highest resolution mode at lowest bandwidth | 8 | ||
| Noise in pressure, full bandwidth | Vp,full | 1.2 | Pa | Full bandwidth, highest resolution | 8 | ||
| Noise in pressure, filtered | Vp,filtered | 0.03 | Pa | Lowest bandwidth, highest resolution | 8 | ||
| Absolute accuracy temperature at 25 °C | AT | -0.3 | 0.3 | °C | @ 25 °C | 8 | |
| Absolute accuracy temperature | AT | -0.5 | 0.5 | °C | 0 . . . +65 °C | 8 | |
| Long term stability pressure | ∆Pstab | -0.33 | 0.33 | hPa | 12 months | 8 | |
| Solder drift pressure | -1 | 1 | hPa | Minimum solder height 50 µm | 8 | ||
| Start-up time | tstartup | 2 | ms | Time to first communication after both VDD > 1.58V and VDDIO > 0.65V | 8 | ||
| Possible sampling rate | fsample | 200 | Hz | osrs_t = osrs_p = 1 | 8 | ||
| ODR accuracy | ∆tstandby | -125 | 125 | % | 25°C | 8 | |
| Supply voltage at any supply pin VDD and VDDIO | -0.3 | 3.8 | V | Pin | 9 | ||
| Voltage at any interface pin | Vss | -0.3 | V | max VDDIO + 0.3 V | 9 | ||
| Storage temperature | -45 | 85 | °C | ≤ 65% rel. H. | 9 | ||
| Overpressure survivability | POVER | 2e+06 | Pa | 9 | |||
| Mechanical shock | MS | 12000 | g | MIL-STD-883H 2002.5 | 9 |
CAD (Adom-generated)
- Symbol:
BMP388 - Footprint:
Adom_Gen:Bosch_Sensortec_BMP388_516d84 - 3D model: generated to fit the land (STEP)
- 3D model files:
bmp388-etched.step/bmp388-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);bmp388.step/bmp388.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Bosch Sensortec datasheet (59 pp, sha256
1ab21c90aaf15542, retrieved 2026-11-18) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.