Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS54394PWPR

Texas Instruments · DC-DC Converters · HTSSOP-16-EP

TPS54394PWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN1 power_in Power input for both channels, rated 4.5V to 18V, connected to high-side NFET drains.
2 VBST1 power_in Bootstrap supply for channel 1 high-side FET gate driver; connect 0.1µF ceramic capacitor between VBST1 and SW1.
3 SW1 output Switch node output for channel 1 at junction of high-side and low-side FETs; input of current comparator.
4 PGND1 power_in Power ground return for channel 1 low-side MOSFET; used as reference for current sensing via SWx-PGNDx voltage measurement.
5 EN1 input Enable input for channel 1; pull above 2.0V to enable converter or below 0.4V to disable.
6 PG1 output Open-drain power good output for channel 1; goes high when output within ±16% of target after 1.5ms delay, goes low after 2µs if out of regulation.
7 VFB1 input D-CAP2 feedback input for channel 1; connect output voltage via resistor divider to set output voltage at 0.765V nominal.
8 GND power_in Signal ground; connect sensitive feedback and soft-start signal returns at a single point.
9 VREG5 power_out 5.5V linear regulator output; bypass with ≥1µF ceramic capacitor to GND (active when EN is high).
10 VFB2 input D-CAP2 feedback input for channel 2; connect output voltage via resistor divider to set output voltage at 0.765V nominal.
11 PG2 output Open-drain power good output for channel 2; goes high when output within ±16% of target after 1.5ms delay, goes low after 2µs if out of regulation.
12 EN2 input Enable input for channel 2; pull above 2.0V to enable converter or below 0.4V to disable.
13 PGND2 power_in Power ground return for channel 2 low-side MOSFET; used as reference for current sensing via SWx-PGNDx voltage measurement.
14 SW2 output Switch node output for channel 2 at junction of high-side and low-side FETs; input of current comparator.
15 VBST2 power_in Bootstrap supply for channel 2 high-side FET gate driver; connect 0.1µF ceramic capacitor between VBST2 and SW2.
16 VIN2 power_in Power input for 5.5V linear regulator, rated 4.5V to 18V.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage range VIN1, VIN2, EN1, EN2 -0.3 20 V 2
Input voltage range VBST1, VBST2 -0.3 26 V 2
Input voltage range VBST1, VBST2 (10ns transient) -0.3 28 V 10ns transient 2
Input voltage range VBST1–SW1, VBST2–SW2 -0.3 6.5 V 2
Input voltage range VFB1, VFB2 -0.3 6.5 V 2
Input voltage range SW1, SW2 -2 20 V 2
Input voltage range SW1, SW2 (10ns transient) -4.5 22 V 10ns transient 2
Output voltage range VREG5, PG1, PG2 -0.3 6.5 V 2
Output voltage range PGND1, PGND2 -0.3 0.3 V 2
TA Operating ambient temperature range TA -40 85 °C 2
TSTG Storage temperature range TSTG -55 150 °C 2
TJ Junction temperature range TJ -40 150 °C 2
Supply input voltage range VIN1, VIN2 4.5 18 V 3
Recommended input voltage range VBST1, VBST2 -0.1 24 V 3
Recommended input voltage range VBST1, VBST2 (10ns transient) -0.1 27 V 10ns transient 3
Recommended input voltage range VBST1–SW1, VBST2–SW2 -0.1 5.7 V 3
Recommended input voltage range VFB1, VFB2 -0.1 5.7 V 3
Recommended input voltage range EN1, EN2 -0.1 18 V 3
Recommended input voltage range SW1, SW2 -1 18 V 3
Recommended input voltage range SW1, SW2 (10ns transient) -4.5 21 V 10ns transient 3
Recommended output voltage range VREG5, PG1, PG2 -0.1 5.7 V 3
Recommended output voltage range PGND1, PGND2 -0.1 0.1 V 3
Recommended output voltage range VO1, VO2 0.76 7 V 3
TA Operating free-air temperature TA -40 85 °C 3
TJ Operating junction temperature TJ -40 150 °C 3
VIN supply current IIN 1200 2000 µA TA = 25°C, EN1 = EN2 = 5 V, VFB1 = VFB2 = 0.8 V 3
VIN shutdown current IVINSDN 15 20 µA TA = 25°C, EN1 = EN2 = 0 V 3
VFBx threshold voltage VVFBTHLx 758 765 773 mV TA = 25°C, CH1 = 3.3 V, CH2 = 1.5 V 3
VFBx temperature coefficient TCVFBx -115 115 ppm/℃ On the basis of 25°C 3
VFB input current IVFBx -0.4 0.2 0.4 µA VFBx = 0.8 V, TA = 25°C 3
PGx pull-down resistance RPG 50 75 110 Ω VPGx = 0.5 V 4
ENx input resistance RENx_IN 225 450 900 kΩ ENx = 12 V 4
Current limit IOCL 3.5 4.7 6.5 A LOUT = 2.2 µH 4
Output UVP trip threshold measured on VFBx VUVP 63 68 73 % measured on VFBx 4
Junction-to-ambient thermal resistance (PWP) θJA 41.4 °C/W 2
Junction-to-case (top) thermal resistance (PWP) θJCtop 27.1 °C/W 2
Junction-to-board thermal resistance (PWP) θJB 20.8 °C/W 2
Junction-to-top characterization parameter (PWP) ψJT 1 °C/W 2
Junction-to-board characterization parameter (PWP) ψJB 20.6 °C/W 2
Junction-to-case (bottom) thermal resistance (PWP) θJCbot 2.7 °C/W 2

CAD (KiCad official)

  • Symbol: TPS54394PWPR
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: tps54394pwpr-etched.step / tps54394pwpr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps54394pwpr.step / tps54394pwpr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (32 pp, sha256 d048a180d36720dd, retrieved 2026-09-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF