3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNCP1681BAD2R2G
onsemi · AC-DC Controllers And Regulators · SOIC-20-NB
NCP1681BAD2R2G from onsemi, in a SOIC-20-NB. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FAULT | input | Combined OVP/OTP fault pin that latches the controller when pulled above VFLT(OVP), typically 3.0 V, and disables it when pulled below VFLT(OTP), typically 0.4 V. |
| 2 | PFCOK | bidirectional | Held low when the PFC output is out of regulation or in a fault condition, and sources a current proportional to VFB once regulation is reached; it can enable a downstream converter and be pulled low by it to force Skip/Standby mode. |
| 3 | FB | input | Senses the PFC output voltage for loop regulation, with an absolute maximum input of 5.5 V relative to AGND. |
| 4 | VM | output | Multiplier output that provides the voltage used for duty cycle modulation. |
| 5 | AGND | power_in | Signal ground reference to which all Maximum Ratings voltages are measured. |
| 6 | CS | input | Senses the inductor current upslope through current sense transformers for cycle-by-cycle current limiting, with an input voltage range of −0.3 V to 5.5 V. |
| 7 | ZCD | input | Senses the inductor current downslope to detect demagnetization and control the synchronous (1-D) switch, with an input voltage range of −0.3 V to 5.5 V. |
| 8 | INVPOL | output | Inverted output of the internal AC polarity detection circuit, rated −0.3 V to 14 V. |
| 9 | SRH | output | Control signal for the high-side slow leg device, rated −0.3 V to 14 V. |
| 10 | SRL | output | Control signal for the low-side slow leg device, rated −0.3 V to 14 V. |
| 11 | POLARITY | output | Output of the internal AC polarity detection circuit, rated −0.3 V to 14 V. |
| 12 | PGND | power_in | Power ground reference, with a maximum voltage of −0.3 V to +0.3 V. |
| 13 | PWML | output | PWM logic-level output that controls the low-side fast leg switch, with a maximum voltage of 5.5 V. |
| 14 | PWMH | output | PWM logic-level output that controls the high-side fast leg switch, with a maximum voltage of 5.5 V. |
| 15 | VCC | power_in | IC supply pin rated −0.3 V to 30 V with respect to AGND. |
| 16 | AUX | input | Monitors switch node resonance on the auxiliary winding to enable valley turn-on in CrM/DCM, and must be tied to GND for CCM operation (NCP1681Ax devices); input voltage −0.3 V to 5.5 V. |
| 18 | LVSNS1 | input | Low voltage input for AC line voltage monitoring, with its resistor divider connected to the AC line side of the boost inductor. |
| 20 | LVSNS2 | input | Low voltage input for AC line voltage monitoring, with its resistor divider connected to the slow leg bridge node. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-20-NB |
| Category | Power Management (PMIC) |
| Pins | 18 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Startup Threshold | VCC(on) | 9.75 | 10.5 | 11.25 | V | VCC increasing | 6 |
| Supply Voltage Minimum Operating Voltage | VCC(off) | 8.2 | 8.8 | 9.4 | V | VCC decreasing | 6 |
| VCC Hysteresis (VCC(on), VCC(off)) | VCC(HYS) | 1.2 | 1.7 | V | VCC decreasing | 6 | |
| Supply Current Before Startup | ICC1 | 1.8 | 2.2 | mA | VCC = 9.5 V | 6 | |
| Supply Current Fault or Latch | ICC2 | 1.8 | 2.2 | mA | VFLT = 0 V | 6 | |
| Supply Current Operational, Switching at 100 kHz | ICC3 | 3.3 | 4 | mA | All DRVs Open | 6 | |
| Supply Current Operational, Skipping | ICC4 | 0.54 | 0.9 | mA | VPFCOK = 0 V | 6 | |
| Line Sag and Brown-Out Upper Threshold | VBO(START) | 1.02 | 1.1 | 1.18 | V | /VLVSNS1 − VLVSNS2/ Increasing | 6 |
| Line Sag and Brown-Out Lower Threshold | VBO(STOP) | 0.92 | 1 | 1.08 | V | /VLVSNS1 − VLVSNS2/ Decreasing | 6 |
| Brown-Out Detection Hysteresis | VBO(HYS) | 60 | 100 | mV | /VLVSNS1 − VLVSNS2/ Increasing | 6 | |
| High-Line Level Detection Threshold | VHL | 2.2 | 2.36 | 2.52 | V | /VLVSNS1 − VLVSNS2/ Increasing | 7 |
| Low-Line Level Detection Threshold | VLL | 2.07 | 2.22 | 2.37 | V | /VLVSNS1 − VLVSNS2/ Decreasing | 7 |
| Line Frequency Upper Threshold | tLINE(65) | 66 | 72 | 78 | Hz | 7 | |
| Line Frequency Lower Threshold | tLINE(45) | 37 | 41 | 45 | Hz | 7 | |
| Feedback Voltage Reference | VREF | 2.475 | 2.5 | 2.525 | V | @ 25°C | 9 |
| Feedback Voltage Reference over temperature range | VREF | 2.44 | 2.5 | 2.56 | V | Over the temperature range | 9 |
| CCM Switching Frequency | FCCM | 60.4 | 65 | 69.6 | kHz | NCP1681AA, BA | 9 |
| Maximum duty cycle in CCM Operation | DMAX | 92.7 | 95.1 | 97.5 | % | VM = 0 V; NCP1681AA, BA | 9 |
| Minimum On-Time | Ton, min | 200 | 260 | 320 | ns | VFB > VREF; CPWMx = Open | 9 |
| Low-Line Current Limit Threshold | VILIMIT1(LL) | 1.33 | 1.4 | 1.47 | V | NCP1681BA | 11 |
| High-Line Current Limit Threshold | VILIMIT1(HL) | 0.8 | 0.84 | 0.88 | V | /VLS1 − VLS2/ = 3; NCP1681BA | 11 |
| Threshold for Abnormal Current Detection | VILIMIT2 | 1.995 | 2.1 | 2.205 | V | VILIMIT2 = 1.5 * VILIMIT1(LL); NCP1681BA | 11 |
| OTP Fault Threshold | VFLT(OTP) | 0.38 | 0.4 | 0.42 | V | VFault decreasing | 12 |
| OVP Fault Threshold | VFLT(OVP) | 2.88 | 3 | 3.12 | V | VFault increasing | 12 |
| Ratio (soft OVP Threshold) over VREF | RsoftOVP | 104 | 105 | 106 | % | VFB increasing | 11 |
| Ratio (Fast OVP Threshold) over soft OVP Upper Threshold | RfastOVP1 | 102.4 | 103 | 103.4 | % | VFB increasing | 11 |
| BUV threshold | VBUV | 1.95 | 2 | 2.05 | V | VFB decreasing | 12 |
| PFCOK voltage in OFF mode | VPFCOK(low) | 100 | mV | PFCOK pin sink current = 1 mA | 12 | ||
| PFCOK current | IPFCOK | 23 | 25 | 27 | µA | VFB = 2.5 V, VPFCOK = 1 V | 12 |
| Non-overlap time between falling edge of PWM(d) & rising edge of PWM(1-d) | TDT1 | 90 | 130 | 170 | ns | VZCD = 0.5 V | 8 |
| Non-overlap time between falling edge of PWM(1-d) rising edge of PWM(d) | TDT2 | 110 | 150 | 190 | ns | VZCD = 0.5 V | 8 |
| PWMx Clamp Voltage | VPWMx(high) | 4.5 | 5 | 5.5 | V | RPWMx = 10 k | 8 |
| VM Pin Source Current Low Line | IM1,LL | 30.4 | 35.7 | 41 | µA | VFB = 2 V, VCS = 1 V | 10 |
| Propagation delay to (1-D) Drive Pulse | TZCD(ARM) | 45 | 75 | ns | Step VZCD 0 V to VZCD(ARM) + 250 mV; Time to PWMx = 2.5 V | 10 | |
| Threshold Minimum VCS for CCM Detection | VCS_CCM−H | 325 | 350 | 375 | mV | 10 | |
| Minimum Operating Time in CrM Mode after CCM to CrM Transition | TCrM(Min) | 210 | 262 | 314 | ms | 10 | |
| Minimum Current Threshold for THD Enhancer Enable (NCP1681BA) | VCS(MIN) | 45 | 70 | 95 | mV | VCS increasing | 11 |
| VM Threshold Voltage to Enter Skip Mode (NCP1681BA Only) | VSKIP(th) | 1.2 | 1.5 | 1.8 | V | NCP1681BA Only | 12 |
| Supply Voltage Absolute Maximum VCC pin | VCC(MAX) | -0.3 | 30 | V | 5 | ||
| PGND Maximum Voltage | VPGND(MAX) | -0.3 | 0.3 | V | 5 | ||
| PWML pin Maximum Voltage | VPWML(MAX) | -0.3 | 5.5 | V | 5 | ||
| PWML pin Maximum Source Current | IPWML(SRC_MAX) | -100 | mA | 5 | |||
| PWML pin Maximum Sink Current | IPWML(SNK_MAX) | 160 | mA | 5 | |||
| PWMH pin Maximum Voltage | VPWMH(MAX) | -0.3 | 5.5 | V | 5 | ||
| PWMH pin Maximum Source Current | IPWMH(SRC_MAX) | -100 | mA | 5 | |||
| PWMH pin Maximum Sink Current | IPWMH(SNK_MAX) | 160 | mA | 5 | |||
| SRx, Polarity, INVPOL pin Maximum Voltage | VSRx(MAX) | -0.3 | 14 | V | 5 | ||
| SRx, Polarity, INVPOL pin Maximum Source Current | ISRx(SRC_MAX) | -100 | mA | 5 | |||
| SRx, Polarity, INVPOL pin Maximum Sink Current | ISRx(SNK_MAX) | 160 | mA | 5 | |||
| AUX pin Input Voltage | VAUX | -0.3 | 5.5 | V | Note 1 | 5 | |
| AUX pin Input Current | IAUX | -2 | 5 | mA | 5 | ||
| ZCD pin Input Voltage Range | VZCD | -0.3 | 5.5 | V | Note 1 | 5 | |
| ZCD pin Maximum Current | IZCD(MAX) | -2 | 5 | mA | 5 | ||
| Maximum Input Voltage Other Pins (LVSNS1, LVSNS2, CS, VM, FB, FAULT) | VMAX | -0.3 | 5.5 | V | Note 1 | 5 | |
| Maximum Current Other Pins (LVSNS1, LVSNS2, CS, VM, FB, FAULT) | IMAX | -2 | 5 | mA | 5 | ||
| Maximum Power Dissipation | PD | 660 | mW | TA = 70°C | 5 | ||
| Thermal Resistance Junction-to-Air | RJA | 121 | °C/W | 1 Oz Cu, 0.155 Sq Inch Printed Circuit Copper Clad | 5 | ||
| Maximum Junction Temperature | TJ(MAX) | 150 | °C | 5 | |||
| Operating Temperature Range | -40 | 125 | °C | 5 | |||
| Storage Temperature Range | -60 | 150 | °C | 5 |
CAD (Adom-generated)
- Symbol:
NCP1681BAD2R2G - Footprint:
Adom_Gen:onsemi_NCP1681_3de34b - 3D model: generated to fit the land (STEP)
- 3D model files:
ncp1681bad2r2g-etched.step/ncp1681bad2r2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp1681bad2r2g.step/ncp1681bad2r2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (43 pp, sha256
a6c997b53885e3c5, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.