main
Download ZIP Propose a change
Generated by adom_assets · KiCad file format 20240108
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ncp1681bad2r2g: viewers · Ray
ncp1681bad2r2g-etched.glb ncp1681bad2r2g: factory component page (tier=mfr) · Ray
ncp1681bad2r2g-etched.step ncp1681bad2r2g: factory component page (tier=mfr) · Ray
ncp1681bad2r2g-hero.glb ncp1681bad2r2g: hero GLB from the etched model (keeps the MPN mark) · Ray
ncp1681bad2r2g-hero.overlay.json ncp1681bad2r2g: hero GLB from the etched model (keeps the MPN mark) · Ray
ncp1681bad2r2g.glb Publish 0.1.0 · Ray
ncp1681bad2r2g.kicad_mod Publish 0.1.0 · Ray
ncp1681bad2r2g.kicad_sym Publish 0.1.0 · Ray
ncp1681bad2r2g.lbr Publish 0.1.0 · Ray
ncp1681bad2r2g.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 18 pins · Ray

NCP1681BAD2R2G

onsemi · AC-DC Controllers And Regulators · SOIC-20-NB

NCP1681BAD2R2G from onsemi, in a SOIC-20-NB. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 FAULT input Combined OVP/OTP fault pin that latches the controller when pulled above VFLT(OVP), typically 3.0 V, and disables it when pulled below VFLT(OTP), typically 0.4 V.
2 PFCOK bidirectional Held low when the PFC output is out of regulation or in a fault condition, and sources a current proportional to VFB once regulation is reached; it can enable a downstream converter and be pulled low by it to force Skip/Standby mode.
3 FB input Senses the PFC output voltage for loop regulation, with an absolute maximum input of 5.5 V relative to AGND.
4 VM output Multiplier output that provides the voltage used for duty cycle modulation.
5 AGND power_in Signal ground reference to which all Maximum Ratings voltages are measured.
6 CS input Senses the inductor current upslope through current sense transformers for cycle-by-cycle current limiting, with an input voltage range of −0.3 V to 5.5 V.
7 ZCD input Senses the inductor current downslope to detect demagnetization and control the synchronous (1-D) switch, with an input voltage range of −0.3 V to 5.5 V.
8 INVPOL output Inverted output of the internal AC polarity detection circuit, rated −0.3 V to 14 V.
9 SRH output Control signal for the high-side slow leg device, rated −0.3 V to 14 V.
10 SRL output Control signal for the low-side slow leg device, rated −0.3 V to 14 V.
11 POLARITY output Output of the internal AC polarity detection circuit, rated −0.3 V to 14 V.
12 PGND power_in Power ground reference, with a maximum voltage of −0.3 V to +0.3 V.
13 PWML output PWM logic-level output that controls the low-side fast leg switch, with a maximum voltage of 5.5 V.
14 PWMH output PWM logic-level output that controls the high-side fast leg switch, with a maximum voltage of 5.5 V.
15 VCC power_in IC supply pin rated −0.3 V to 30 V with respect to AGND.
16 AUX input Monitors switch node resonance on the auxiliary winding to enable valley turn-on in CrM/DCM, and must be tied to GND for CCM operation (NCP1681Ax devices); input voltage −0.3 V to 5.5 V.
18 LVSNS1 input Low voltage input for AC line voltage monitoring, with its resistor divider connected to the AC line side of the boost inductor.
20 LVSNS2 input Low voltage input for AC line voltage monitoring, with its resistor divider connected to the slow leg bridge node.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-20-NB
Category Power Management (PMIC)
Pins 18

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage Startup Threshold VCC(on) 9.75 10.5 11.25 V VCC increasing 6
Supply Voltage Minimum Operating Voltage VCC(off) 8.2 8.8 9.4 V VCC decreasing 6
VCC Hysteresis (VCC(on), VCC(off)) VCC(HYS) 1.2 1.7 V VCC decreasing 6
Supply Current Before Startup ICC1 1.8 2.2 mA VCC = 9.5 V 6
Supply Current Fault or Latch ICC2 1.8 2.2 mA VFLT = 0 V 6
Supply Current Operational, Switching at 100 kHz ICC3 3.3 4 mA All DRVs Open 6
Supply Current Operational, Skipping ICC4 0.54 0.9 mA VPFCOK = 0 V 6
Line Sag and Brown-Out Upper Threshold VBO(START) 1.02 1.1 1.18 V /VLVSNS1 − VLVSNS2/ Increasing 6
Line Sag and Brown-Out Lower Threshold VBO(STOP) 0.92 1 1.08 V /VLVSNS1 − VLVSNS2/ Decreasing 6
Brown-Out Detection Hysteresis VBO(HYS) 60 100 mV /VLVSNS1 − VLVSNS2/ Increasing 6
High-Line Level Detection Threshold VHL 2.2 2.36 2.52 V /VLVSNS1 − VLVSNS2/ Increasing 7
Low-Line Level Detection Threshold VLL 2.07 2.22 2.37 V /VLVSNS1 − VLVSNS2/ Decreasing 7
Line Frequency Upper Threshold tLINE(65) 66 72 78 Hz 7
Line Frequency Lower Threshold tLINE(45) 37 41 45 Hz 7
Feedback Voltage Reference VREF 2.475 2.5 2.525 V @ 25°C 9
Feedback Voltage Reference over temperature range VREF 2.44 2.5 2.56 V Over the temperature range 9
CCM Switching Frequency FCCM 60.4 65 69.6 kHz NCP1681AA, BA 9
Maximum duty cycle in CCM Operation DMAX 92.7 95.1 97.5 % VM = 0 V; NCP1681AA, BA 9
Minimum On-Time Ton, min 200 260 320 ns VFB > VREF; CPWMx = Open 9
Low-Line Current Limit Threshold VILIMIT1(LL) 1.33 1.4 1.47 V NCP1681BA 11
High-Line Current Limit Threshold VILIMIT1(HL) 0.8 0.84 0.88 V /VLS1 − VLS2/ = 3; NCP1681BA 11
Threshold for Abnormal Current Detection VILIMIT2 1.995 2.1 2.205 V VILIMIT2 = 1.5 * VILIMIT1(LL); NCP1681BA 11
OTP Fault Threshold VFLT(OTP) 0.38 0.4 0.42 V VFault decreasing 12
OVP Fault Threshold VFLT(OVP) 2.88 3 3.12 V VFault increasing 12
Ratio (soft OVP Threshold) over VREF RsoftOVP 104 105 106 % VFB increasing 11
Ratio (Fast OVP Threshold) over soft OVP Upper Threshold RfastOVP1 102.4 103 103.4 % VFB increasing 11
BUV threshold VBUV 1.95 2 2.05 V VFB decreasing 12
PFCOK voltage in OFF mode VPFCOK(low) 100 mV PFCOK pin sink current = 1 mA 12
PFCOK current IPFCOK 23 25 27 µA VFB = 2.5 V, VPFCOK = 1 V 12
Non-overlap time between falling edge of PWM(d) & rising edge of PWM(1-d) TDT1 90 130 170 ns VZCD = 0.5 V 8
Non-overlap time between falling edge of PWM(1-d) rising edge of PWM(d) TDT2 110 150 190 ns VZCD = 0.5 V 8
PWMx Clamp Voltage VPWMx(high) 4.5 5 5.5 V RPWMx = 10 k 8
VM Pin Source Current Low Line IM1,LL 30.4 35.7 41 µA VFB = 2 V, VCS = 1 V 10
Propagation delay to (1-D) Drive Pulse TZCD(ARM) 45 75 ns Step VZCD 0 V to VZCD(ARM) + 250 mV; Time to PWMx = 2.5 V 10
Threshold Minimum VCS for CCM Detection VCS_CCM−H 325 350 375 mV 10
Minimum Operating Time in CrM Mode after CCM to CrM Transition TCrM(Min) 210 262 314 ms 10
Minimum Current Threshold for THD Enhancer Enable (NCP1681BA) VCS(MIN) 45 70 95 mV VCS increasing 11
VM Threshold Voltage to Enter Skip Mode (NCP1681BA Only) VSKIP(th) 1.2 1.5 1.8 V NCP1681BA Only 12
Supply Voltage Absolute Maximum VCC pin VCC(MAX) -0.3 30 V 5
PGND Maximum Voltage VPGND(MAX) -0.3 0.3 V 5
PWML pin Maximum Voltage VPWML(MAX) -0.3 5.5 V 5
PWML pin Maximum Source Current IPWML(SRC_MAX) -100 mA 5
PWML pin Maximum Sink Current IPWML(SNK_MAX) 160 mA 5
PWMH pin Maximum Voltage VPWMH(MAX) -0.3 5.5 V 5
PWMH pin Maximum Source Current IPWMH(SRC_MAX) -100 mA 5
PWMH pin Maximum Sink Current IPWMH(SNK_MAX) 160 mA 5
SRx, Polarity, INVPOL pin Maximum Voltage VSRx(MAX) -0.3 14 V 5
SRx, Polarity, INVPOL pin Maximum Source Current ISRx(SRC_MAX) -100 mA 5
SRx, Polarity, INVPOL pin Maximum Sink Current ISRx(SNK_MAX) 160 mA 5
AUX pin Input Voltage VAUX -0.3 5.5 V Note 1 5
AUX pin Input Current IAUX -2 5 mA 5
ZCD pin Input Voltage Range VZCD -0.3 5.5 V Note 1 5
ZCD pin Maximum Current IZCD(MAX) -2 5 mA 5
Maximum Input Voltage Other Pins (LVSNS1, LVSNS2, CS, VM, FB, FAULT) VMAX -0.3 5.5 V Note 1 5
Maximum Current Other Pins (LVSNS1, LVSNS2, CS, VM, FB, FAULT) IMAX -2 5 mA 5
Maximum Power Dissipation PD 660 mW TA = 70°C 5
Thermal Resistance Junction-to-Air RJA 121 °C/W 1 Oz Cu, 0.155 Sq Inch Printed Circuit Copper Clad 5
Maximum Junction Temperature TJ(MAX) 150 °C 5
Operating Temperature Range -40 125 °C 5
Storage Temperature Range -60 150 °C 5

CAD (Adom-generated)

  • Symbol: NCP1681BAD2R2G
  • Footprint: Adom_Gen:onsemi_NCP1681_3de34b
  • 3D model: generated to fit the land (STEP)
  • 3D model files: ncp1681bad2r2g-etched.step / ncp1681bad2r2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp1681bad2r2g.step / ncp1681bad2r2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (43 pp, sha256 a6c997b53885e3c5, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.

Datasheet PDF