3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS54626PWPR
Texas Instruments · DC-DC Converters · HTSSOP-14-EP
TPS54626PWPR from Texas Instruments, in a HTSSOP-14-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VO | power_out | Connect to output of converter; also used for the output discharge function. |
| 2 | VFB | input | Converter feedback input; connect with a feedback resistor divider from VO. |
| 3 | VREG5 | power_out | 5.5V internal linear regulator output for control circuitry; a typical 1uF capacitor should be connected to GND; not active when EN is low. |
| 4 | SS | passive | Soft-start control pin; an external capacitor connected to GND sets the soft-start ramp time (6uA typical charge current). |
| 5 | GND | power_in | Signal ground pin for the control circuitry. |
| 6 | PG | output | Open-drain power-good output; requires an external pull-up resistor (25k-150kOhm) to VREG5. |
| 7 | EN | input | Enable control input, active high; must be pulled up to enable the device (internal pull-down resistance to GND of 200-800kOhm). |
| 8 | PGND1 | power_in | Ground return for the low-side MOSFET; also serves as an input to the current comparator; connect strongly to GND near the IC. |
| 9 | PGND2 | power_in | Ground return for the low-side MOSFET; also serves as an input to the current comparator; connect strongly to GND near the IC. |
| 10 | SW1 | output | Switch node connection between the high-side and low-side NFETs; also serves as an input to the current comparator. |
| 11 | SW2 | output | Switch node connection between the high-side and low-side NFETs; also serves as an input to the current comparator. |
| 12 | VBST | passive | Supply input for the high-side NFET gate driver (boost terminal); connect a capacitor from this pin to the SW1/SW2 terminals; an internal PN diode connects VREG5 to this pin. |
| 13 | VIN1 | power_in | Power input, connected to the high-side NFET drain. |
| 14 | VIN2 | power_in | Power input, connected to the high-side NFET drain; an additional 0.1uF capacitor from this pin to ground is recommended to improve stability of the over-current limit function. |
| 15 | PowerPAD | power_in | Exposed thermal pad on the package backside, internally connected to PGND; must be soldered to the PCB ground plane to achieve appropriate power dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-14-EP |
| Category | Power Supply Chip |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Absolute max input voltage (VIN1, VIN2, EN) | VIN1, VIN2, EN | -0.3 | 20 | V | 2 | ||
| Absolute max VBST voltage | VBST | -0.3 | 26 | V | 2 | ||
| Absolute max VBST voltage (10 ns transient) | VBST | -0.3 | 28 | V | 10 ns transient | 2 | |
| Absolute max VBST voltage vs Sw1, SW2 | VBST (vs Sw1, SW2) | -0.3 | 6.5 | V | 2 | ||
| Absolute max VFB, VO, SS, PG voltage | VFB, VO, SS, PG | -0.3 | 6.5 | V | 2 | ||
| Absolute max SW1, SW2 voltage | SW1, SW2 | -2 | 20 | V | 2 | ||
| Absolute max SW1, SW2 voltage (10 ns transient) | SW1, SW2 | -3 | 22 | V | 10 ns transient | 2 | |
| Absolute max VREG5 voltage | VREG5 | -0.3 | 6.5 | V | 2 | ||
| Absolute max PGND1, PGND2 voltage | PGND1, PGND2 | -0.3 | 0.3 | V | 2 | ||
| Absolute max voltage from GND to POWERPAD | Vdiff | -0.2 | 0.2 | V | 2 | ||
| ESD rating Human Body Model | 2 | kV | Human Body Model (HBM) | 2 | |||
| ESD rating Charged Device Model | 500 | V | Charged Device Model (CDM) | 2 | |||
| Absolute max operating junction temperature | TJ | -40 | 150 | °C | 2 | ||
| Absolute max storage temperature | Tstg | -55 | 150 | °C | 2 | ||
| Supply input voltage range | VIN | 4.5 | 18 | V | 3 | ||
| Recommended VBST voltage | VBST | -0.1 | 24 | V | 3 | ||
| Recommended VBST voltage (10 ns transient) | VBST | -0.1 | 27 | V | 10 ns transient | 3 | |
| Recommended VBST voltage vs SW | VBST (vs SW) | -0.1 | 6 | V | 3 | ||
| Recommended SS, PG input voltage | SS, PG | -0.1 | 5.7 | V | 3 | ||
| Recommended EN input voltage | EN | -0.1 | 18 | V | 3 | ||
| Recommended VO, VFB voltage | VO, VFB | -0.1 | 5.5 | V | 3 | ||
| Recommended SW1, SW2 voltage | SW1, SW2 | -1.8 | 18 | V | 3 | ||
| Recommended SW1, SW2 voltage (10 ns transient) | SW1, SW2 | -3 | 21 | V | 10 ns transient | 3 | |
| Recommended PGND1, PGND2 voltage | PGND1, PGND2 | -0.1 | 0.1 | V | 3 | ||
| Recommended VREG5 voltage | VREG5 | -0.1 | 5.7 | V | 3 | ||
| Recommended IVREG5 output current | IVREG5 | 0 | 5 | mA | 3 | ||
| Power Good resistor RPG | RPG | 25 | 150 | kΩ | 3 | ||
| Operating free-air temperature | TA | -40 | 85 | °C | 3 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 3 | ||
| VIN operating non-switching supply current | IVIN | 950 | 1400 | μA | TA = 25°C, EN = 5 V, VVFB = 0.8 V | 3 | |
| VIN shutdown supply current | IVINSDN | 3.6 | 10 | μA | TA = 25°C, EN = 0 V | 3 | |
| EN high-level input voltage | VENH | 1.6 | V | 3 | |||
| EN low-level input voltage | VENL | 0.6 | V | 3 | |||
| EN pin resistance to GND | REN | 200 | 400 | 800 | kΩ | VEN = 12 V | 3 |
| VFB threshold voltage (continuous mode, 25°C) | VFBTH | 757 | 765 | 773 | mV | TA = 25°C, VO = 1.05 V, continuous mode | 3 |
| VFB threshold voltage (continuous mode, 0°C to 85°C) | VFBTH | 753 | 777 | mV | TA = 0°C to 85°C, VO = 1.05 V, continuous mode (1) | 3 | |
| VFB threshold voltage (continuous mode, -40°C to 85°C) | VFBTH | 751 | 779 | mV | TA = –40°C to 85°C, VO = 1.05 V, continuous mode (1) | 3 | |
| VFB input current | IVFB | -0.15 | 0 | 0.15 | μA | VVFB = 0.8 V, TA = 25°C | 3 |
| VO discharge resistance | RDischg | 100 | 150 | Ω | VEN = 0 V, VO = 0.5 V, TA = 25°C | 3 | |
| VREG5 output voltage | VVREG5 | 5.2 | 5.5 | 5.7 | V | TA = 25°C, 6 V < VIN < 18 V, 0 < IVREG5 < 5 mA | 3 |
| VREG5 output current | IVREG5 | 20 | mA | VIN = 6 V, VVREG5 = 4 V, TA = 25°C | 3 | ||
| Current limit | Iocl | 7.2 | 8.2 | 9.5 | A | L = 1.5 μH (2) | 4 |
| TOFF(MIN) minimum off time | TOFF(MIN) | 260 | 310 | ns | TA = 25°C, VFB = 0.7 V | 4 | |
| SS charge current | ISSC | 4.2 | 6 | 7.8 | μA | VSS = 1.0 V | 4 |
| SS discharge current | ISSD | 1.5 | 3.3 | mA | VSS = 0.5 V | 4 | |
| PG threshold (VVFB rising, good) | VTHPG | 85 | 90 | 95 | % | VVFB rising (good) | 4 |
| PG sink current | IPG | 2.5 | 5 | mA | VPG = 0.5 V | 4 | |
| Output OVP trip threshold | VOVP | 120 | 125 | 130 | % | OVP detect | 4 |
| Output UVP trip threshold | VUVP | 60 | 65 | 70 | % | UVP detect | 4 |
| UVLO wake up VREG5 voltage | VUVLO | 3.45 | 3.75 | 4.05 | V | Wake up VREG5 voltage | 4 |
| UVLO hysteresis VREG5 voltage | VUVLO | 0.13 | 0.32 | 0.48 | V | Hysteresis | 4 |
| High side switch resistance | Rdsonh | 36 | mΩ | TA = 25°C, VBST-SW1,2 = 5.5V | 3 | ||
| Low side switch resistance | Rdsonl | 28 | mΩ | TA = 25°C | 3 | ||
| On time | TON | 150 | ns | VIN = 12 V, VO = 1.05 V | 4 | ||
| Thermal shutdown threshold | TSDN | 165 | °C | 4 | |||
| Output UVP delay | TUVPDEL | 0.25 | ms | 4 | |||
| Junction-to-ambient thermal resistance | θJA | 40.5 | °C/W | PWP (14 pins) | 2 | ||
| Junction-to-case (top) thermal resistance | θJCtop | 28.7 | °C/W | PWP (14 pins) | 2 | ||
| Junction-to-board thermal resistance | θJB | 24.2 | °C/W | PWP (14 pins) | 2 | ||
| Junction-to-case (bottom) thermal resistance | θJCbot | 2.4 | °C/W | PWP (14 pins) | 2 |
CAD (KiCad official)
- Symbol:
TPS54626PWPR - Footprint:
Package_SO:TSSOP-14-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-14-EP (KiCad packages3D, STEP)
- 3D model files:
tps54626pwpr-etched.step/tps54626pwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps54626pwpr.step/tps54626pwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (23 pp, sha256
6a77b8bc07cb116a, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).