3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownM24C02-DRDW8TP
STMicroelectronics · EEPROM · TSSOP-8
M24C02-DRDW8TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | E0 | input | Chip enable input that sets bit b1 of the 7-bit device select code; it must be tied to VCC or VSS, and when left floating it is read as low (0). |
| 2 | E1 | input | Chip enable input that sets bit b2 of the 7-bit device select code; it must be tied to VCC or VSS, and when left floating it is read as low (0). |
| 3 | E2 | input | Chip enable input that sets bit b3 of the 7-bit device select code; it must be tied to VCC or VSS, and when left floating it is read as low (0). |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage. |
| 5 | SDA | bidirectional | Serial data I/O; an open-drain output that may be wire-OR'ed with other open-drain or open-collector signals, requiring a pull-up resistor between SDA and VCC. |
| 6 | SCL | input | Serial clock input that strobes the data available on SDA in and outputs data on SDA. |
| 7 | WC | input | Write control input; when driven high, write operations to the entire memory array are disabled (device select and address bytes are acknowledged, data bytes are not), and when driven low or left floating writes are enabled. |
| 8 | VCC | power_in | Supply voltage pin, specified from 1.7 V to 5.5 V over the -40 °C to 105 °C ambient range. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Write cycle endurance | Ncycle | 1.2e+06 | TA = 85 °C, 1.7 V < VCC < 5.5 V | 28 | |||
| Write cycle endurance | Ncycle | 900000 | TA = 105 °C, 1.7 V < VCC < 5.5 V | 28 | |||
| Ambient operating temperature | -40 | 130 | °C | 26 | |||
| Input or output range | VIO | -0.5 | 6.5 | V | 26 | ||
| DC output current (SDA = 0) | IOL | 5 | mA | SDA = 0 | 26 | ||
| Supply voltage | VCC | -0.5 | 6.5 | V | 26 | ||
| Electrostatic pulse (Human Body model) | VESD | 4000 | V | HBM, AEC-Q100-002 | 26 | ||
| Supply voltage | VCC | 1.7 | 5.5 | V | voltage range R | 27 | |
| Ambient operating temperature | TA | -40 | 105 | °C | voltage range R | 27 | |
| Input capacitance (SDA) | CIN | 8 | pF | 28 | |||
| Input capacitance (other pins) | CIN | 6 | pF | 28 | |||
| Input impedance (WC) | ZL | 30 | kΩ | VIN < 0.3 VCC | 28 | ||
| Input impedance (WC) | ZH | 500 | kΩ | VIN > 0.7 VCC | 28 | ||
| Input leakage current (SCL, SDA, Ei) | ILI | -2 | 2 | µA | VIN = VSS or VCC, device in Standby mode | 29 | |
| Output leakage current | ILO | -2 | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 29 | |
| Supply current (Read) | ICC | 2 | mA | fC = 400 kHz, VCC = 5.5 V | 29 | ||
| Supply current (Read) | ICC | 1 | mA | fC = 400 kHz, VCC = 1.7 V | 29 | ||
| Supply current (Write) | ICC0 | 2 | mA | During tW | 29 | ||
| Standby supply current | ICC1 | 1 | µA | Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 1.7 V | 29 | ||
| Standby supply current | ICC1 | 2 | µA | Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 2.5 V | 29 | ||
| Standby supply current | ICC1 | 3 | µA | Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 5.5 V | 29 | ||
| Input low voltage (SCL, SDA, WC, Ei) | VIL | -0.45 | V | 29 | |||
| Input high voltage (SCL, SDA) | VIH | 6.5 | V | 29 | |||
| Output low voltage | VOL | 0.4 | V | IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V | 29 | ||
| Output low voltage | VOL | 0.3 | V | IOL = 1 mA, VCC = 1.7 V | 29 | ||
| Internal reset threshold voltage | VRES | 0.5 | 1.5 | V | 29 | ||
| Clock frequency (400 kHz) | fC | 400 | kHz | 30 | |||
| Clock pulse width high (400 kHz) | tCHCL | 600 | ns | 30 | |||
| Clock pulse width low (400 kHz) | tCLCH | 1300 | ns | 30 | |||
| SDA (out) fall time (400 kHz) | tQL1QL2 | 20 | 120 | ns | CL = 10 pF | 30 | |
| Data in setup time (400 kHz) | tDXCH | 100 | ns | 30 | |||
| Data in hold time (400 kHz) | tCLDX | 0 | ns | 30 | |||
| Data out hold time (400 kHz) | tCLQX | 100 | ns | 30 | |||
| Clock low to next data valid (access time) (400 kHz) | tCLQV | 900 | ns | Rbus × Cbus within Figure 10 values | 30 | ||
| Start condition setup time (400 kHz) | tCHDL | 600 | ns | 30 | |||
| Start condition hold time (400 kHz) | tDLCL | 600 | ns | 30 | |||
| Stop condition set up time (400 kHz) | tCHDH | 600 | ns | 30 | |||
| Time between Stop and next Start (400 kHz) | tDHDL | 1300 | ns | 30 | |||
| WC set up time (before the Start condition) (400 kHz) | tSU:WC | 0 | µs | WC=0 set up time to enable WRITE | 30 | ||
| WC hold time (after the Stop condition) (400 kHz) | tHD:WC | 1 | µs | WC=0 hold time to enable WRITE | 30 | ||
| Write time | tW | 4 | ms | 30 | |||
| Clock frequency (1 MHz) | fC | 0 | 1 | MHz | 31 | ||
| Clock pulse width high (1 MHz) | tCHCL | 260 | ns | 31 | |||
| Clock pulse width low (1 MHz) | tCLCH | 500 | ns | 31 | |||
| SDA (out) fall time (1 MHz) | tQL1QL2 | 20 | 120 | ns | 31 | ||
| Data in setup time (1 MHz) | tDXCH | 50 | ns | 31 | |||
| Data in hold time (1 MHz) | tCLDX | 0 | ns | 31 | |||
| Data out hold time (1 MHz) | tCLQX | 100 | ns | 31 | |||
| Clock low to next data valid (access time) (1 MHz) | tCLQV | 450 | ns | Rbus × Cbus within Figure 11 values | 31 | ||
| Start condition setup time (1 MHz) | tCHDL | 250 | ns | 31 | |||
| Start condition hold time (1 MHz) | tDLCL | 250 | ns | 31 | |||
| Stop condition setup time (1 MHz) | tCHDH | 250 | ns | 31 | |||
| Time between Stop and next Start (1 MHz) | tDHDL | 500 | ns | 31 | |||
| WC set up time (before the Start condition) (1 MHz) | tSU:WC | 0 | µs | WC=0 set up time to enable WRITE | 31 | ||
| WC hold time (after the Stop condition) (1 MHz) | tHD:WC | 1 | µs | WC=0 hold time to enable WRITE | 31 | ||
| Write time | tW | 4 | ms | 31 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST | 26 |
CAD (KiCad official)
- Symbol:
M24C02-DRDW8TP - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m24c02-drdw8tp-k-etched.step/m24c02-drdw8tp-k-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m24c02-drdw8tp-k.step/m24c02-drdw8tp-k.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (42 pp, sha256
ca15ee09e38f09bf, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).