Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

M24C02-DRDW8TP

STMicroelectronics · EEPROM · TSSOP-8

M24C02-DRDW8TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 E0 input Chip enable input that sets bit b1 of the 7-bit device select code; it must be tied to VCC or VSS, and when left floating it is read as low (0).
2 E1 input Chip enable input that sets bit b2 of the 7-bit device select code; it must be tied to VCC or VSS, and when left floating it is read as low (0).
3 E2 input Chip enable input that sets bit b3 of the 7-bit device select code; it must be tied to VCC or VSS, and when left floating it is read as low (0).
4 VSS power_in Ground, the reference for the VCC supply voltage.
5 SDA bidirectional Serial data I/O; an open-drain output that may be wire-OR'ed with other open-drain or open-collector signals, requiring a pull-up resistor between SDA and VCC.
6 SCL input Serial clock input that strobes the data available on SDA in and outputs data on SDA.
7 WC input Write control input; when driven high, write operations to the entire memory array are disabled (device select and address bytes are acknowledged, data bytes are not), and when driven low or left floating writes are enabled.
8 VCC power_in Supply voltage pin, specified from 1.7 V to 5.5 V over the -40 °C to 105 °C ambient range.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Write cycle endurance Ncycle 1.2e+06 TA = 85 °C, 1.7 V < VCC < 5.5 V 28
Write cycle endurance Ncycle 900000 TA = 105 °C, 1.7 V < VCC < 5.5 V 28
Ambient operating temperature -40 130 °C 26
Input or output range VIO -0.5 6.5 V 26
DC output current (SDA = 0) IOL 5 mA SDA = 0 26
Supply voltage VCC -0.5 6.5 V 26
Electrostatic pulse (Human Body model) VESD 4000 V HBM, AEC-Q100-002 26
Supply voltage VCC 1.7 5.5 V voltage range R 27
Ambient operating temperature TA -40 105 °C voltage range R 27
Input capacitance (SDA) CIN 8 pF 28
Input capacitance (other pins) CIN 6 pF 28
Input impedance (WC) ZL 30 kΩ VIN < 0.3 VCC 28
Input impedance (WC) ZH 500 kΩ VIN > 0.7 VCC 28
Input leakage current (SCL, SDA, Ei) ILI -2 2 µA VIN = VSS or VCC, device in Standby mode 29
Output leakage current ILO -2 2 µA SDA in Hi-Z, external voltage applied on SDA: VSS or VCC 29
Supply current (Read) ICC 2 mA fC = 400 kHz, VCC = 5.5 V 29
Supply current (Read) ICC 1 mA fC = 400 kHz, VCC = 1.7 V 29
Supply current (Write) ICC0 2 mA During tW 29
Standby supply current ICC1 1 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 1.7 V 29
Standby supply current ICC1 2 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 2.5 V 29
Standby supply current ICC1 3 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 5.5 V 29
Input low voltage (SCL, SDA, WC, Ei) VIL -0.45 V 29
Input high voltage (SCL, SDA) VIH 6.5 V 29
Output low voltage VOL 0.4 V IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V 29
Output low voltage VOL 0.3 V IOL = 1 mA, VCC = 1.7 V 29
Internal reset threshold voltage VRES 0.5 1.5 V 29
Clock frequency (400 kHz) fC 400 kHz 30
Clock pulse width high (400 kHz) tCHCL 600 ns 30
Clock pulse width low (400 kHz) tCLCH 1300 ns 30
SDA (out) fall time (400 kHz) tQL1QL2 20 120 ns CL = 10 pF 30
Data in setup time (400 kHz) tDXCH 100 ns 30
Data in hold time (400 kHz) tCLDX 0 ns 30
Data out hold time (400 kHz) tCLQX 100 ns 30
Clock low to next data valid (access time) (400 kHz) tCLQV 900 ns Rbus × Cbus within Figure 10 values 30
Start condition setup time (400 kHz) tCHDL 600 ns 30
Start condition hold time (400 kHz) tDLCL 600 ns 30
Stop condition set up time (400 kHz) tCHDH 600 ns 30
Time between Stop and next Start (400 kHz) tDHDL 1300 ns 30
WC set up time (before the Start condition) (400 kHz) tSU:WC 0 µs WC=0 set up time to enable WRITE 30
WC hold time (after the Stop condition) (400 kHz) tHD:WC 1 µs WC=0 hold time to enable WRITE 30
Write time tW 4 ms 30
Clock frequency (1 MHz) fC 0 1 MHz 31
Clock pulse width high (1 MHz) tCHCL 260 ns 31
Clock pulse width low (1 MHz) tCLCH 500 ns 31
SDA (out) fall time (1 MHz) tQL1QL2 20 120 ns 31
Data in setup time (1 MHz) tDXCH 50 ns 31
Data in hold time (1 MHz) tCLDX 0 ns 31
Data out hold time (1 MHz) tCLQX 100 ns 31
Clock low to next data valid (access time) (1 MHz) tCLQV 450 ns Rbus × Cbus within Figure 11 values 31
Start condition setup time (1 MHz) tCHDL 250 ns 31
Start condition hold time (1 MHz) tDLCL 250 ns 31
Stop condition setup time (1 MHz) tCHDH 250 ns 31
Time between Stop and next Start (1 MHz) tDHDL 500 ns 31
WC set up time (before the Start condition) (1 MHz) tSU:WC 0 µs WC=0 set up time to enable WRITE 31
WC hold time (after the Stop condition) (1 MHz) tHD:WC 1 µs WC=0 hold time to enable WRITE 31
Write time tW 4 ms 31

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST 26

CAD (KiCad official)

  • Symbol: M24C02-DRDW8TP
  • Footprint: Package_SO:TSSOP-8_4.4x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: m24c02-drdw8tp-k-etched.step / m24c02-drdw8tp-k-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m24c02-drdw8tp-k.step / m24c02-drdw8tp-k.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (42 pp, sha256 ca15ee09e38f09bf, retrieved 2026-11-10, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF