Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

IS32FL3740-ZLA3-TR

Lumissil Microsystems · LED Drivers · TSSOP-20-EP

IS32FL3740-ZLA3-TR from Lumissil Microsystems, in a TSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 AVCC power_in Power supply for analog circuits (supply range 2.7V to 5.5V).
2 RSET passive Input terminal for an external resistor that regulates the current source DC current value.
3 SYNC bidirectional Synchronize pin used for multi-part synchronized operation (output as master, input as slave, high impedance when disabled); float if not used.
4 SDA bidirectional I2C compatible serial data.
5 SCL input I2C compatible serial clock.
6 ADDR input I2C address setting.
7 INTB output Active-low interrupt output whose function is set by register F0h; can be left floating if the interrupt function is not used.
8 SDB input Shuts down the chip when pulled low.
9 GND power_in Ground connection.
10 SW1 passive Switch pin for LED matrix scanning (SW1).
11 PGND power_in Power ground.
12 SW2 passive Switch pin for LED matrix scanning (SW2).
13 PGND power_in Power ground.
14 SW3 passive Switch pin for LED matrix scanning (SW3).
15 CS1 passive Current source output 1; maximum current is 84mA with REXT=20kΩ.
16 CS2 passive Current source output 2; maximum current is 84mA with REXT=20kΩ.
17 PVCC power_in Power supply for the current sources.
18 CS3 passive Current source output 3; maximum current is 84mA with REXT=20kΩ.
19 CS4 passive Current source output 4; maximum current is 84mA with REXT=20kΩ.
20 VIO power_in Input logic reference voltage.
21 Thermal Pad power_in Exposed thermal pad that needs to be connected to GND pins.

Key specifications

Parameter Value
Manufacturer Lumissil Microsystems
Package TSSOP-20-EP
Category Display Modules / LED Drivers / Display Drivers
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC 2.7 5.5 V 6
Supply voltage (absolute maximum) VCC -0.3 6 V 6
Voltage at any input pin -0.3 6 V -0.3V ~ VCC+0.3V 6
Maximum junction temperature TJMAX 150 °C 6
Storage temperature range TSTG -65 150 °C 6
Operating temperature range TA -40 125 °C 6
Thermal resistance junction to ambient θJA 45.4 °C/W 6
ESD (HBM) -2 2 kV ±2kV 6
ESD (CDM) -750 750 V ±750V 6
Shutdown current ISD 3 µA VSDB=0V 6
Quiescent power supply current ICC 2.17 mA VSDB=VCC, all LEDs off 6
Maximum constant current of CS1~CS4 IOUT 84 mA RSET=20kΩ 6
Average current on each LED ILED 26.3 mA RSET=20kΩ, GCC=255, All PWM = 255 6
Current sink headroom voltage SW1~SW3 VHR 200 mV ISINK=336mA (Note 1, 2) 6
Current source headroom voltage CS1~CS4 VHR 350 mV ISOURCE=84mA (Note 1) 6
Period of scanning tSCAN 128 µs 6
Non-overlap blanking time tNOL 8 µs 6
Logic 0 input voltage VIL 0.2 V VIO=3.6V; max printed as 0.2VIO 6
Logic 1 input voltage VIH 0.75 V VIO=3.6V; min printed as 0.75VIO 6
Input schmitt trigger hysteresis VHYS 0.2 V VIO=3.6V 6
Logic 0 output voltage for SYNC VOL 0.4 V IOL = 8mA 6
Logic 1 output voltage for SYNC VOH 0.75 V IOH = 8mA; min printed as 0.75VIO 6
Logic 0 input current IIL 5 nA VINPUT = 0V (Note 3) 6
Logic 1 input current IIH 5 nA VINPUT = VIO (Note 3) 6
Serial-clock frequency (Fast Mode) fSCL 400 kHz Fast Mode 7
Serial-clock frequency (Fast Mode Plus) fSCL 1000 kHz Fast Mode Plus 7
Bus free time STOP to START (Fast Mode) tBUF 1.3 µs Fast Mode 7
Bus free time STOP to START (Fast Mode Plus) tBUF 0.5 µs Fast Mode Plus 7
Hold time repeated START (Fast Mode) tHD,STA 0.6 µs Fast Mode 7
Hold time repeated START (Fast Mode Plus) tHD,STA 0.26 µs Fast Mode Plus 7
Repeated START setup time (Fast Mode) tSU,STA 0.6 µs Fast Mode 7
Repeated START setup time (Fast Mode Plus) tSU,STA 0.26 µs Fast Mode Plus 7
STOP condition setup time (Fast Mode) tSU,STO 0.6 µs Fast Mode 7
STOP condition setup time (Fast Mode Plus) tSU,STO 0.26 µs Fast Mode Plus 7
Data setup time (Fast Mode) tSU,DAT 100 ns Fast Mode 7
Data setup time (Fast Mode Plus) tSU,DAT 50 ns Fast Mode Plus 7
SCL clock low period (Fast Mode) tLOW 1.3 µs Fast Mode 7
SCL clock low period (Fast Mode Plus) tLOW 0.5 µs Fast Mode Plus 7
SCL clock high period (Fast Mode) tHIGH 0.7 µs Fast Mode 7
SCL clock high period (Fast Mode Plus) tHIGH 0.26 µs Fast Mode Plus 7
Rise time of SDA and SCL (Fast Mode) tR 300 ns Fast Mode, receiving 7
Rise time of SDA and SCL (Fast Mode Plus) tR 120 ns Fast Mode Plus, receiving 7
Fall time of SDA and SCL (Fast Mode) tF 300 ns Fast Mode, receiving 7
Fall time of SDA and SCL (Fast Mode Plus) tF 120 ns Fast Mode Plus, receiving 7

CAD (KiCad official)

  • Symbol: IS32FL3740-ZLA3-TR
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: TSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: is32fl3740-zla3-tr-etched.step / is32fl3740-zla3-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); is32fl3740-zla3-tr.step / is32fl3740-zla3-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Lumissil Microsystems datasheet (31 pp, sha256 ac09b6bc5db26474, retrieved 2026-11-02, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF