Generated by kicad-footprint-generator · KiCad file format 20260206
IS32FL3740-ZLA3-TR
Lumissil Microsystems · LED Drivers · TSSOP-20-EP
IS32FL3740-ZLA3-TR from Lumissil Microsystems, in a TSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVCC | power_in | Power supply for analog circuits (supply range 2.7V to 5.5V). |
| 2 | RSET | passive | Input terminal for an external resistor that regulates the current source DC current value. |
| 3 | SYNC | bidirectional | Synchronize pin used for multi-part synchronized operation (output as master, input as slave, high impedance when disabled); float if not used. |
| 4 | SDA | bidirectional | I2C compatible serial data. |
| 5 | SCL | input | I2C compatible serial clock. |
| 6 | ADDR | input | I2C address setting. |
| 7 | INTB | output | Active-low interrupt output whose function is set by register F0h; can be left floating if the interrupt function is not used. |
| 8 | SDB | input | Shuts down the chip when pulled low. |
| 9 | GND | power_in | Ground connection. |
| 10 | SW1 | passive | Switch pin for LED matrix scanning (SW1). |
| 11 | PGND | power_in | Power ground. |
| 12 | SW2 | passive | Switch pin for LED matrix scanning (SW2). |
| 13 | PGND | power_in | Power ground. |
| 14 | SW3 | passive | Switch pin for LED matrix scanning (SW3). |
| 15 | CS1 | passive | Current source output 1; maximum current is 84mA with REXT=20kΩ. |
| 16 | CS2 | passive | Current source output 2; maximum current is 84mA with REXT=20kΩ. |
| 17 | PVCC | power_in | Power supply for the current sources. |
| 18 | CS3 | passive | Current source output 3; maximum current is 84mA with REXT=20kΩ. |
| 19 | CS4 | passive | Current source output 4; maximum current is 84mA with REXT=20kΩ. |
| 20 | VIO | power_in | Input logic reference voltage. |
| 21 | Thermal Pad | power_in | Exposed thermal pad that needs to be connected to GND pins. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Lumissil Microsystems |
| Package | TSSOP-20-EP |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 2.7 | 5.5 | V | 6 | ||
| Supply voltage (absolute maximum) | VCC | -0.3 | 6 | V | 6 | ||
| Voltage at any input pin | -0.3 | 6 | V | -0.3V ~ VCC+0.3V | 6 | ||
| Maximum junction temperature | TJMAX | 150 | °C | 6 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 6 | ||
| Operating temperature range | TA | -40 | 125 | °C | 6 | ||
| Thermal resistance junction to ambient | θJA | 45.4 | °C/W | 6 | |||
| ESD (HBM) | -2 | 2 | kV | ±2kV | 6 | ||
| ESD (CDM) | -750 | 750 | V | ±750V | 6 | ||
| Shutdown current | ISD | 3 | µA | VSDB=0V | 6 | ||
| Quiescent power supply current | ICC | 2.17 | mA | VSDB=VCC, all LEDs off | 6 | ||
| Maximum constant current of CS1~CS4 | IOUT | 84 | mA | RSET=20kΩ | 6 | ||
| Average current on each LED | ILED | 26.3 | mA | RSET=20kΩ, GCC=255, All PWM = 255 | 6 | ||
| Current sink headroom voltage SW1~SW3 | VHR | 200 | mV | ISINK=336mA (Note 1, 2) | 6 | ||
| Current source headroom voltage CS1~CS4 | VHR | 350 | mV | ISOURCE=84mA (Note 1) | 6 | ||
| Period of scanning | tSCAN | 128 | µs | 6 | |||
| Non-overlap blanking time | tNOL | 8 | µs | 6 | |||
| Logic 0 input voltage | VIL | 0.2 | V | VIO=3.6V; max printed as 0.2VIO | 6 | ||
| Logic 1 input voltage | VIH | 0.75 | V | VIO=3.6V; min printed as 0.75VIO | 6 | ||
| Input schmitt trigger hysteresis | VHYS | 0.2 | V | VIO=3.6V | 6 | ||
| Logic 0 output voltage for SYNC | VOL | 0.4 | V | IOL = 8mA | 6 | ||
| Logic 1 output voltage for SYNC | VOH | 0.75 | V | IOH = 8mA; min printed as 0.75VIO | 6 | ||
| Logic 0 input current | IIL | 5 | nA | VINPUT = 0V (Note 3) | 6 | ||
| Logic 1 input current | IIH | 5 | nA | VINPUT = VIO (Note 3) | 6 | ||
| Serial-clock frequency (Fast Mode) | fSCL | 400 | kHz | Fast Mode | 7 | ||
| Serial-clock frequency (Fast Mode Plus) | fSCL | 1000 | kHz | Fast Mode Plus | 7 | ||
| Bus free time STOP to START (Fast Mode) | tBUF | 1.3 | µs | Fast Mode | 7 | ||
| Bus free time STOP to START (Fast Mode Plus) | tBUF | 0.5 | µs | Fast Mode Plus | 7 | ||
| Hold time repeated START (Fast Mode) | tHD,STA | 0.6 | µs | Fast Mode | 7 | ||
| Hold time repeated START (Fast Mode Plus) | tHD,STA | 0.26 | µs | Fast Mode Plus | 7 | ||
| Repeated START setup time (Fast Mode) | tSU,STA | 0.6 | µs | Fast Mode | 7 | ||
| Repeated START setup time (Fast Mode Plus) | tSU,STA | 0.26 | µs | Fast Mode Plus | 7 | ||
| STOP condition setup time (Fast Mode) | tSU,STO | 0.6 | µs | Fast Mode | 7 | ||
| STOP condition setup time (Fast Mode Plus) | tSU,STO | 0.26 | µs | Fast Mode Plus | 7 | ||
| Data setup time (Fast Mode) | tSU,DAT | 100 | ns | Fast Mode | 7 | ||
| Data setup time (Fast Mode Plus) | tSU,DAT | 50 | ns | Fast Mode Plus | 7 | ||
| SCL clock low period (Fast Mode) | tLOW | 1.3 | µs | Fast Mode | 7 | ||
| SCL clock low period (Fast Mode Plus) | tLOW | 0.5 | µs | Fast Mode Plus | 7 | ||
| SCL clock high period (Fast Mode) | tHIGH | 0.7 | µs | Fast Mode | 7 | ||
| SCL clock high period (Fast Mode Plus) | tHIGH | 0.26 | µs | Fast Mode Plus | 7 | ||
| Rise time of SDA and SCL (Fast Mode) | tR | 300 | ns | Fast Mode, receiving | 7 | ||
| Rise time of SDA and SCL (Fast Mode Plus) | tR | 120 | ns | Fast Mode Plus, receiving | 7 | ||
| Fall time of SDA and SCL (Fast Mode) | tF | 300 | ns | Fast Mode, receiving | 7 | ||
| Fall time of SDA and SCL (Fast Mode Plus) | tF | 120 | ns | Fast Mode Plus, receiving | 7 |
CAD (KiCad official)
- Symbol:
IS32FL3740-ZLA3-TR - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: TSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
is32fl3740-zla3-tr-etched.step/is32fl3740-zla3-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);is32fl3740-zla3-tr.step/is32fl3740-zla3-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Lumissil Microsystems datasheet (31 pp, sha256
ac09b6bc5db26474, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).