3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3472EDD#PBF
Analog Devices · DC-DC Converters · DFN-10-EP(3x3)
LT3472EDD#PBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SWP | output | Switch pin for the positive (boost) channel; connect the boost inductor here. |
| 2 | VIN | power_in | Input supply pin that must be locally bypassed with an X5R or X7R type ceramic capacitor; the operating input range is 2.2V to 16V. |
| 3 | SHDN | input | Shutdown pin that must be connected to 0.8V or higher to enable the device and 0.3V or less to disable it. |
| 4 | SWN | output | Switch pin for the negative (inverter) channel; connect the inverter input inductor and flying capacitor here. |
| 5 | DN | passive | Anode of the internal Schottky diode for the inverter; connect the inverter output inductor and flying capacitor here. |
| 6 | FBN | input | Inverter feedback pin; connect feedback resistor R2 from this pin to VO2 with VO2 = 1.25 • R2/50k, and the pin is at 0V when regulated. |
| 7 | SSN | passive | Inverter soft-start pin, internally connected to 1.25V through a 50k resistor; a capacitor to ground programs the ramp, and leaving it open or pulling it above 1.25V gives a quick start. |
| 8 | FBP | input | Boost feedback pin; connect feedback resistor R1 from this pin to VO1 with VO1 = 1.25 • (1 + R1/50k), and the pin is at 1.25V when regulated. |
| 9 | SSP | passive | Boost soft-start pin, internally connected to 1.25V through a 50k resistor; a capacitor to ground programs the ramp, and leaving it open or pulling it above 1.25V gives a quick start. |
| 10 | VPOS | power_out | Boost output pin; connect the boost output capacitor here, with the switch and output nodes rated to 36V maximum. |
| 11 | GND | power_in | Exposed pad ground pin that must be tied to the ground plane through multiple vias under the package and soldered to the PCB for thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Operation Voltage | 2.2 | V | 2 | ||||
| Maximum Operation Voltage | 16 | V | 2 | ||||
| Supply Current | 2.8 | mA | SHDN = 3V, Not Switching | 2 | |||
| Supply Current | 0.1 | 1 | µA | SHDN = 0V | 2 | ||
| SHDN Voltage High | 0.8 | V | Full operating temperature range (●) | 2 | |||
| SHDN Voltage Low | 0.3 | V | Full operating temperature range (●) | 2 | |||
| SHDN Pin Bias Current | 35 | µA | SHDN = 3V | 2 | |||
| Positive Feedback Voltage | 1.2 | 1.25 | 1.3 | V | Full operating temperature range (●) | 2 | |
| Negative Feedback Voltage | -5 | 0 | 5 | mV | Full operating temperature range (●) | 2 | |
| Positive Feedback Voltage Line Regulation | 0.01 | %/V | 2 | ||||
| Negative Feedback Voltage Line Regulation | 0.008 | mV/V | 2 | ||||
| FBP Current | 24.5 | 25 | 25.3 | µA | FBP = VFBP, Full operating temperature range (●) | 2 | |
| FBN Current | 24.5 | 25 | 25.3 | µA | FBN = VFBN, Full operating temperature range (●) | 2 | |
| FBP to Start Negative Channel | 1.02 | 1.1 | 1.18 | V | 2 | ||
| Switching Frequency | 0.9 | 1.1 | 1.4 | MHz | 2 | ||
| Maximum Duty Cycle (Both Channels) | 88 | 92 | % | Full operating temperature range (●) | 2 | ||
| Positive Channel Switch Current Limit | 250 | 350 | mA | Full operating temperature range (●) | 2 | ||
| Negative Channel Switch Current Limit | 300 | 400 | mA | Full operating temperature range (●) | 2 | ||
| Positive Channel Switch VCESAT | 245 | mV | ISWP = 200mA | 2 | |||
| Negative Channel Switch VCESAT | 400 | mV | ISWN = 200mA | 2 | |||
| Switch Leakage Current (Both Channels) | 0.01 | 5 | µA | VSW = 5V | 2 | ||
| Schottky DP Forward Drop | 700 | 950 | mV | IDP = 150mA | 2 | ||
| Schottky DN Forward Drop | 750 | 1000 | mV | IDN = 150mA | 2 | ||
| Schottky Leakage Current (Both Channels) | 4 | µA | VR = 36V | 2 | |||
| VIN, SHDN Voltage | 16 | V | 2 | ||||
| SWP, SWN, VPOS Voltage | 36 | V | 2 | ||||
| DN Voltage | -36 | V | 2 | ||||
| FBP, FBN, SSP, SSN Voltage | 10 | V | 2 | ||||
| Maximum Junction Temperature | TJMAX | 125 | °C | 2 | |||
| Operating Temperature Range (Extended Commercial) | -40 | 85 | °C | 2 | |||
| Storage Temperature Range | -65 | 125 | °C | 2 | |||
| Thermal Resistance, Junction to Ambient | θJA | 43 | °C/W | 2 | |||
| Thermal Resistance, Junction to Case | θJC | 3 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LT3472EDD#PBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt3472edd-pbf-etched.step/lt3472edd-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3472edd-pbf.step/lt3472edd-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (12 pp, sha256
c9419d0f587a0a49, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).