Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3472EDD#PBF

Analog Devices · DC-DC Converters · DFN-10-EP(3x3)

LT3472EDD#PBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SWP output Switch pin for the positive (boost) channel; connect the boost inductor here.
2 VIN power_in Input supply pin that must be locally bypassed with an X5R or X7R type ceramic capacitor; the operating input range is 2.2V to 16V.
3 SHDN input Shutdown pin that must be connected to 0.8V or higher to enable the device and 0.3V or less to disable it.
4 SWN output Switch pin for the negative (inverter) channel; connect the inverter input inductor and flying capacitor here.
5 DN passive Anode of the internal Schottky diode for the inverter; connect the inverter output inductor and flying capacitor here.
6 FBN input Inverter feedback pin; connect feedback resistor R2 from this pin to VO2 with VO2 = 1.25 • R2/50k, and the pin is at 0V when regulated.
7 SSN passive Inverter soft-start pin, internally connected to 1.25V through a 50k resistor; a capacitor to ground programs the ramp, and leaving it open or pulling it above 1.25V gives a quick start.
8 FBP input Boost feedback pin; connect feedback resistor R1 from this pin to VO1 with VO1 = 1.25 • (1 + R1/50k), and the pin is at 1.25V when regulated.
9 SSP passive Boost soft-start pin, internally connected to 1.25V through a 50k resistor; a capacitor to ground programs the ramp, and leaving it open or pulling it above 1.25V gives a quick start.
10 VPOS power_out Boost output pin; connect the boost output capacitor here, with the switch and output nodes rated to 36V maximum.
11 GND power_in Exposed pad ground pin that must be tied to the ground plane through multiple vias under the package and soldered to the PCB for thermal performance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-10-EP(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Operation Voltage 2.2 V 2
Maximum Operation Voltage 16 V 2
Supply Current 2.8 mA SHDN = 3V, Not Switching 2
Supply Current 0.1 1 µA SHDN = 0V 2
SHDN Voltage High 0.8 V Full operating temperature range (●) 2
SHDN Voltage Low 0.3 V Full operating temperature range (●) 2
SHDN Pin Bias Current 35 µA SHDN = 3V 2
Positive Feedback Voltage 1.2 1.25 1.3 V Full operating temperature range (●) 2
Negative Feedback Voltage -5 0 5 mV Full operating temperature range (●) 2
Positive Feedback Voltage Line Regulation 0.01 %/V 2
Negative Feedback Voltage Line Regulation 0.008 mV/V 2
FBP Current 24.5 25 25.3 µA FBP = VFBP, Full operating temperature range (●) 2
FBN Current 24.5 25 25.3 µA FBN = VFBN, Full operating temperature range (●) 2
FBP to Start Negative Channel 1.02 1.1 1.18 V 2
Switching Frequency 0.9 1.1 1.4 MHz 2
Maximum Duty Cycle (Both Channels) 88 92 % Full operating temperature range (●) 2
Positive Channel Switch Current Limit 250 350 mA Full operating temperature range (●) 2
Negative Channel Switch Current Limit 300 400 mA Full operating temperature range (●) 2
Positive Channel Switch VCESAT 245 mV ISWP = 200mA 2
Negative Channel Switch VCESAT 400 mV ISWN = 200mA 2
Switch Leakage Current (Both Channels) 0.01 5 µA VSW = 5V 2
Schottky DP Forward Drop 700 950 mV IDP = 150mA 2
Schottky DN Forward Drop 750 1000 mV IDN = 150mA 2
Schottky Leakage Current (Both Channels) 4 µA VR = 36V 2
VIN, SHDN Voltage 16 V 2
SWP, SWN, VPOS Voltage 36 V 2
DN Voltage -36 V 2
FBP, FBN, SSP, SSN Voltage 10 V 2
Maximum Junction Temperature TJMAX 125 °C 2
Operating Temperature Range (Extended Commercial) -40 85 °C 2
Storage Temperature Range -65 125 °C 2
Thermal Resistance, Junction to Ambient θJA 43 °C/W 2
Thermal Resistance, Junction to Case θJC 3 °C/W 2

CAD (KiCad official)

  • Symbol: LT3472EDD#PBF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: lt3472edd-pbf-etched.step / lt3472edd-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3472edd-pbf.step / lt3472edd-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (12 pp, sha256 c9419d0f587a0a49, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF