3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSLMi332CG-DG
Sillumin · Gate Drive ICs · SOP-16-300mil
SLMi332CG-DG from Sillumin, in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VS | power_in | Input-side ground reference for VCC1 and the FAULT output, and the reference for the VCC1 supply range of 3 V to 18 V. |
| 2 | VCC1 | power_in | Positive input-side supply, recommended 3 V to 18 V relative to VS (absolute maximum 20 V), and UVLO on this pin only disables the FAULT pin function below about 2.7 V rising. |
| 3 | FAULT | output | Isolated fault output on the input side, open drain and active low, pulled low when DESAT detects an IGBT fault and not reset automatically (absolute maximum 20 V relative to VS). |
| 4 | VS | power_in | Input-side ground, internally tied to pin 1 as printed, and the common input ground reference for the isolator. |
| 5 | CATHODE | input | Cathode of the input LED; the input forward current when on is recommended at 7 mA to 16 mA and reverse voltage is limited to 30 V. |
| 6 | ANODE | input | Anode of the input LED; recommended anode-to-cathode voltage when off is -30 V to 0.9 V. |
| 7 | ANODE | input | Anode of the input LED (second anode pin, internally tied to pin 6 as printed); same limits as pin 6. |
| 8 | CATHODE | input | Cathode of the input LED (second cathode pin, internally tied to pin 5 as printed); same limits as pin 5. |
| 9 | VEE | power_in | Negative output-side supply, the reference for VCC2 (14 V to 40 V) and the clamp-low level of the gate drive output. |
| 10 | VCLAMP | input | Miller clamp sense pin, which activates the clamp when it falls below about 2 V relative to VEE and must be connected to VOUT to use the soft turn-off feature (absolute maximum 45 V). |
| 11 | VOUT | output | Gate drive output that sources and sinks up to 2.5 A peak to drive the IGBT gate, with output voltage limited between VEE and VCC2. |
| 12 | VEE | power_in | Negative output-side supply (second VEE pin, internally tied to pin 9 as printed), used as the output-stage ground reference. |
| 13 | VCC2 | power_in | Positive output-side supply, recommended 14 V to 40 V relative to VEE, with UVLO that forces VOUT low when below about 10.3 V falling. |
| 14 | DESAT | input | Desaturation voltage input monitoring IGBT VCE, with a trip threshold of 6.5 V (no suffix H) or 9 V (suffix H) and to be connected to VE if not used. |
| 15 | VLED | passive | For internal test only; the datasheet suggests connecting it to VEE. |
| 16 | VE | power_in | Common IGBT emitter output-side reference, with VE to VEE recommended at 0 V to 15 V and the DESAT absolute maximum referenced to this pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sillumin |
| Package | SOP-16-300mil |
| Category | Power Management |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Average Input Current | IF(AVG) | 25 | mA | 6 | |||
| Reverse Input Voltage | VR | 30 | V | 6 | |||
| Input Side Supply Voltage | VCC1 -VS | -0.5 | 20 | V | 6 | ||
| Output Supply Voltage | VCC2 -VEE | -0.5 | 45 | V | 6 | ||
| Negative Output Supply Voltage | VE -VEE | -0.5 | 20 | V | 6 | ||
| Positive Output Supply Voltage (max is 45-(VE-VEE), expression not converted) | VCC2 -VE | -0.5 | V | 6 | |||
| Miller Clamping Voltage | VCLAMP - VEE | -0.5 | 45 | V | 6 | ||
| Fault pin Voltage | VFAULT - VS | -0.5 | 20 | V | 6 | ||
| Junction Temperature | TJ | -40 | 150 | °C | 6 | ||
| Storage Temperature | TS | -55 | 150 | °C | 6 | ||
| Input Side Supply Voltage (recommended) | VCC1 -VS | 3 | 18 | V | 6 | ||
| Output Supply Voltage (recommended) | VCC2 -VEE | 14 | 40 | V | 6 | ||
| Negative Output Supply Voltage (recommended) | VE-VEE | 0 | 15 | V | 6 | ||
| Positive Output Supply Voltage (recommended; max is 40-(VE-VEE), expression not converted) | VCC2 -VE | 14 | V | 6 | |||
| Input Diode Forward Current (Diode ON) | IF(ON) | 7 | 16 | mA | 6 | ||
| Anode Voltage - Cathode Voltage (Diode OFF) | VF(OFF) | -30 | 0.9 | V | 6 | ||
| Junction Temperature (recommended) | TJ | -40 | 150 | °C | 6 | ||
| Ambient Temperature | TA | -40 | 125 | °C | 6 | ||
| Under Voltage Lockout Rising on VCC2 | VUVLO2_R | 10.5 | 11.6 | 12.5 | V | 10 | |
| Under Voltage Lockout Falling on VCC2 | VUVLO2_F | 9.2 | 10.3 | 11.1 | V | 10 | |
| Propagation delay, Low to High | tPLH | 80 | 120 | ns | CLOAD=1nF, fsw=20kHz, (50% Duty Cycle), VCC2=15V | 11 | |
| Propagation delay, High to Low | tPHL | 80 | 120 | ns | 11 | ||
| Output High Level Common Mode Transient Immunity | CMTIH | 150 | kV/us | IF=10mA, VCM=1000V, VCC2=15V, TA=25°C | 11 | ||
| Output Low Level Common Mode Transient Immunity | CMTIL | 150 | kV/us | VF=0V, VCM=1000V, VCC2= 15V, TA=25°C | 11 | ||
| Junction to ambient thermal resistance | RθJA | 100 | °C/W | JESD51-3 low effective thermal conductivity test board | 6 | ||
| Junction to case (top) thermal resistance | RθJC(TOP) | 40 | °C/W | JESD51-3 low effective thermal conductivity test board | 6 | ||
| Input Forward Threshold Current Low to High | IFLH | 2.2 | mA | 9 | |||
| Input Forward Voltage | VF | 2.2 | V | IF=10mA | 9 | ||
| Temp Coefficient of Input Forward Voltage | VF/T | 0.5 | mV/°C | IF=10mA | 9 | ||
| Input Reverse Breakdown Voltage | VR | 30 | V | IR=10uA | 9 | ||
| Clamp Pin Threshold Voltage | VCLAMP | 2 | V | 9 | |||
| DESAT Threshold | VDESAT | 6.5 | V | Without suffix H | 9 | ||
| DESAT Blank Charging Current | ICHG | 0.22 | mA | VDESAT=2V | 9 | ||
| DESAT Blank Discharging Current | IDSCHG | 33 | mA | VDESAT=7V | 9 | ||
| FAULT Output Low Voltage | VFT_LOW | 0.1 | V | IFAULT=1mA, VCC1=5V | 9 | ||
| FAULT Pin Leakage Current | IFT_LK | 0.1 | uA | VFAULT=5V, VCC1=5V | 9 | ||
| High Level Peak Output Current | IOH | 2.5 | A | IF=10mA, CVCC2=10uF, CLOAD=220nF | 9 | ||
| Low Level Peak Output Current | IOL | 2.5 | A | IF=10mA, CVCC2=10uF, CLOAD=220nF | 9 | ||
| Clamp Low Sink Current | ICL | 1.67 | A | 9 | |||
| Low Level Output Current During Fault Condition | IOLF | 0.19 | A | 9 | |||
| High Level Output Voltage | VOH | 60 | mV | IF=10mA, IO=-20mA | 9 | ||
| Low Level Output Voltage | VOL | 30 | mV | VF=0V, IO=20mA | 9 | ||
| Under Voltage Lockout Rising on VCC1 | VUVLO1_R | 2.7 | V | 9 | |||
| Under Voltage Lockout Falling on VCC1 | VUVLO1_F | 2.5 | V | 9 | |||
| Under Voltage Lockout Hysteresis on VCC1 | VUVLO1_HYS | 0.2 | V | 10 | |||
| Under Voltage Lockout Hysteresis on VCC2 | VUVLO2_HYS | 1.3 | V | 10 | |||
| Turn on rise time | tr | 28 | ns | 11 | |||
| Turn off fall time | tf | 25 | ns | 11 | |||
| Pulse Width Distortion | tPWD | 35 | ns | 11 | |||
| UVLO Recovery Delay | tUVLO_REC | 30 | us | VCC2 Rising from 0V to 15V | 11 | ||
| DESAT to 90% VOUT Delay | tDESAT(90%) | 0.15 | us | CBLANK=100pF, CLOAD=10nF | 11 | ||
| DESAT to 10% VOUT Delay | tDESAT(10%) | 0.5 | us | 11 | |||
| DESAT Input Mute | tDESAT(MUTE) | 8 | us | 11 | |||
| DESAT to DESAT Low Propagation Delay | tDESAT(LOW) | 0.2 | us | 11 | |||
| DESAT to FAULT Low Delay | tDESAT(FAULT) | 0.3 | us | 11 | |||
| RESET to High Level FAULT Signal Delay | tRESET(FAULT) | 1 | us | 11 | |||
| Capacitance (Input Side to Output Side) | CIO | 1.6 | pF | 7 | |||
| Input Capacitance | CIN | 30 | pF | 7 |
CAD (KiCad official)
- Symbol:
SLMi332CG-DG - Footprint:
Package_SO:SOIC-16W_7.5x12.8mm_P1.27mm - 3D model: SOP-16-300mil (KiCad packages3D, STEP)
- 3D model files:
slmi332cg-dg-etched.step/slmi332cg-dg-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);slmi332cg-dg.step/slmi332cg-dg.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Sillumin datasheet (16 pp, sha256
a0818e7c2d1c6da6, retrieved 2026-11-13, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).