3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLMP7300MMX
Texas Instruments · Comparators · VSSOP-8
LMP7300MMX from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | +IN | input | Noninverting comparator input with a common-mode range from 1 V above the negative rail to, and including, the positive rail; internal ESD diodes clamp the input to a safe level if it exceeds the rails. |
| 2 | -IN | input | Inverting comparator input with a common-mode range from 1 V above the negative rail to, and including, the positive rail; internal ESD diodes clamp the input to a safe level if it exceeds the rails. |
| 3 | GND | power_in | Ground pin that may be connected to a negative DC supply for dual-supply operation (decouple with a 0.1-µF ceramic capacitor to ground in that case); the internal reference output is referenced to this pin. |
| 4 | OUT | output | Open-collector comparator output that may be pulled up to a maximum of +12 V with respect to the ground pin, irrespective of supply voltage. |
| 5 | HYSTN | input | Negative hysteresis pin that sets the lower trip voltage VIL, with a common-mode range from 1 V above the negative rail to VCC; the input must fall below VIL for the output to switch from high to low. |
| 6 | HYSTP | input | Positive hysteresis pin that sets the upper trip voltage VIH, with a common-mode range from 1 V above the negative rail to VCC; the input must rise above VIH for the output to switch from low to high. |
| 7 | REF | output | Reference voltage output of the 2.048-V band-gap precision reference. |
| 8 | V+ | power_in | Positive supply terminal with a supply voltage range of 2.7 V to 12 V; decouple with a 0.1-µF ceramic capacitor to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Operational Amplifier/Comparator |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Temperature (operating free-air) | -40 | 125 | °C | Over operating free-air temperature range | 4 | ||
| Supply Voltage (VS = V+, V−) | VS | 2.7 | 12 | V | VS = V+, V− | 4 | |
| Supply voltage (VS = V+, V−) | VS | 13.6 | V | 4 | |||
| Infrared or convection soldering temperature | 235 | °C | 20 s | 4 | |||
| Wave soldering lead temperature | 260 | °C | 10 s | 4 | |||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Supply Current | IS | 9 | 12 | µA | 2.7-V table: TA = 25°C, RPULLUP = Open | 5 | |
| Supply Current | IS | 17 | µA | 2.7-V table: TJ = TA, RPULLUP = Open | 5 | ||
| Input Offset Voltage (VSSOP) | VOS | -1 | 0.07 | 1 | mV | 2.7-V table: TA = 25°C, VCM = V+/2, VSSOP | 5 |
| Input Offset Voltage (VSSOP) | VOS | -2.2 | 2.2 | mV | 2.7-V table: TJ = TA, VCM = V+/2, VSSOP | 5 | |
| Input Bias Current | IB | 3 | nA | 2.7-V table: /VID/ < 2.5 V, TA = 25°C | 5 | ||
| Input Bias Current | IB | 4 | nA | 2.7-V table: /VID/ < 2.5 V, TJ = TA | 5 | ||
| Input Offset Current | IOS | 0.15 | 0.5 | nA | 2.7-V table | 5 | |
| Common Mode Rejection Ratio | CMRR | 80 | 100 | dB | 2.7-V table: 1 V < VCM < 2.7 V | 5 | |
| Power Supply Rejection Ratio | PSRR | 80 | 100 | dB | 2.7-V table: V+ = 2.7 V to 12 V | 5 | |
| Output Voltage Low | VOL | 0.25 | 0.4 | V | 2.7-V table: ILOAD = 10 mA, TA = 25°C | 5 | |
| Output Voltage Low | VOL | 0.5 | V | 2.7-V table: ILOAD = 10 mA, TJ = TA | 5 | ||
| Hysteresis Leakage Current | IHYS | 1.2 | 3 | nA | 2.7-V table: TA = 25°C | 5 | |
| Hysteresis Leakage Current | IHYS | 4 | nA | 2.7-V table: TJ = TA | 5 | ||
| Propagation Delay (High to Low) | TPD | 12 | 17 | µs | 2.7-V table: Overdrive = 10 mV, CL = 10 pF | 5 | |
| Propagation Delay (High to Low) | TPD | 4.5 | 7.6 | µs | 2.7-V table: Overdrive = 100 mV, CL = 10 pF | 5 | |
| Reference Voltage (VSSOP) | VO | 2.043 | 2.048 | 2.056 | V | 2.7-V table: VSSOP | 5 |
| Line Regulation | 14 | 80 | µV/V | VCC = 2.7 V to 12 V | 5 | ||
| Load Regulation | 0.2 | 0.5 | mV/mA | 2.7-V table: IOUT = 0 to 1 mA | 5 | ||
| Supply Current | IS | 10 | 13 | µA | 5-V table: TA = 25°C, RPULLUP = Open | 6 | |
| Supply Current | IS | 18 | µA | 5-V table: TJ = TA, RPULLUP = Open | 6 | ||
| Input Offset Voltage (VSSOP) | VOS | -1 | 0.07 | 1 | mV | 5-V table: TA = 25°C, VCM = V+/2, VSSOP | 6 |
| Input Offset Voltage (VSSOP) | VOS | -2.2 | 2.2 | mV | 5-V table: TJ = TA, VCM = V+/2, VSSOP | 6 | |
| Input Bias Current | IB | 1.2 | 3 | nA | 5-V table: /VID/ < 2.5 V, TA = 25°C | 6 | |
| Input Bias Current | IB | 4 | nA | 5-V table: /VID/ < 2.5 V, TJ = TA | 6 | ||
| Input Offset Current | IOS | 0.15 | 0.5 | nA | 5-V table | 6 | |
| Common Mode Rejection Ratio | CMRR | 80 | 100 | dB | 5-V table: 1 ≤ VCM ≤ 5 V | 6 | |
| Power Supply Rejection Ratio | PSRR | 80 | 100 | dB | 5-V table: V+ = 2.7 V to 12 V | 6 | |
| Output Voltage Low | VOL | 0.25 | 0.4 | V | 5-V table: ILOAD = 10 mA | 6 | |
| Hysteresis Leakage Current | IHYS | 1.2 | 3 | nA | 5-V table: TA = 25°C | 6 | |
| Hysteresis Leakage Current | IHYS | 4 | nA | 5-V table: TJ = TA | 6 | ||
| Propagation Delay (High to Low) | TPD | 12 | 15 | µs | 5-V table: Overdrive = 10 mV, CL = 10 pF | 6 | |
| Propagation Delay (High to Low) | TPD | 4 | 7 | µs | 5-V table: Overdrive = 100 mV, CL = 10 pF | 6 | |
| Reference Voltage (VSSOP) | VO | 2.043 | 2.048 | 2.056 | V | 5-V table: VSSOP | 6 |
| Line Regulation | 14 | 80 | µV/V | VCC = 2.7 V to 12 V | 6 | ||
| Load Regulation | 0.2 | 0.5 | mV/mA | 5-V table: IOUT = 0 to 1 mA | 6 | ||
| Supply Current | IS | 11 | 14 | µA | 12-V table: TA = 25°C, RPULLUP = Open | 7 | |
| Supply Current | IS | 20 | µA | 12-V table: TJ = TA, RPULLUP = Open | 7 | ||
| Input Offset Voltage (VSSOP) | VOS | -1 | 0.08 | 1 | mV | 12-V table: TA = 25°C, VCM = V+/2, VSSOP | 7 |
| Input Offset Voltage (VSSOP) | VOS | -2.2 | 2.2 | mV | 12-V table: TJ = TA, VCM = V+/2, VSSOP | 7 | |
| Input Bias Current | IB | 1.2 | 3 | nA | 12-V table: /VID/ > 2.5 V, TA = 25°C | 7 | |
| Input Bias Current | IB | 4 | nA | 12-V table: /VID/ > 2.5 V, TJ = TA | 7 | ||
| Input Offset Current | IOS | 0.15 | 0.5 | nA | 12-V table | 7 | |
| Common Mode Rejection Ratio | CMRR | 80 | 100 | dB | 12-V table: 1 V ≤ VCM ≤ 12 V | 7 | |
| Power Supply Rejection Ratio | PSRR | 80 | 100 | dB | 12-V table: V+ = 2.7 V to 12 V | 7 | |
| Output Voltage Low | VOL | 0.25 | 0.4 | V | 12-V table: ILOAD = 10 mA | 7 | |
| Hysteresis Leakage Current | IHYS | 1.2 | 3 | nA | 12-V table: TA = 25°C | 7 | |
| Hysteresis Leakage Current | IHYS | 4 | nA | 12-V table: TJ = TA | 7 | ||
| Propagation Delay (High to Low) | TPD | 11 | 15 | µs | 12-V table: Overdrive = 10 mV, CL = 10 pF | 7 | |
| Propagation Delay (High to Low) | TPD | 3.5 | 6.8 | µs | 12-V table: Overdrive = 100 mV, CL = 10 pF | 7 | |
| Reference Voltage (VSSOP) | VO | 2.043 | 2.048 | 2.056 | V | 12-V table: TJ = 25°C, VSSOP | 7 |
| Line Regulation | 14 | 80 | µV/V | VCC = 2.7 V to 12 V | 7 | ||
| Load Regulation | 0.2 | 0.5 | mV/mA | 12-V table: IOUT = 0 to 1 mA | 7 | ||
| Junction-to-ambient thermal resistance (DGK VSSOP, 8 pins) | RθJA | 175.5 | °C/W | DGK (VSSOP) 8 pins, soldered to PC board | 4 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
LMP7300MMX - Footprint:
Package_SO:VSSOP-8_3x3mm_P0.65mm - 3D model: VSSOP-8, generated on the KiCad land (body 3 x 3 mm, terminals on the pads, 1.1 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lmp7300mmx-etched.step/lmp7300mmx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmp7300mmx.step/lmp7300mmx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (34 pp, sha256
9cfc88c9102c0010, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).