Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

IPS2200BI1R

RENESAS · Position Sensor · TSSOP-16

IPS2200BI1R from RENESAS, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CSN_IRQN bidirectional Digital pin serving as chip-select input for the SPI interface (external pull-up required) or as push/pull interrupt output for the I2C or SPI interface, with programmable options per Table 3.
2 RX1 input Receiver coil 1 (sine) connects between the RX2 and RX1 pins.
3 RX2 input Receiver coil 1 (sine) connects between the RX2 and RX1 pins.
4 RX3 input Receiver coil 2 (cosine) connects between the RX4 and RX3 pins.
5 RX4 input Receiver coil 2 (cosine) connects between the RX4 and RX3 pins.
6 TX1 bidirectional Transmitter coil connects between TX1 and TX2; resonant frequency is set by a parallel capacitor CT or by capacitors CT1 (TX2 to GND) and CT2 (TX1 to GND).
7 TX2 bidirectional Transmitter coil connects between TX1 and TX2; resonant frequency is set by a parallel capacitor CT or by capacitors CT1 (TX2 to GND) and CT2 (TX1 to GND).
8 VDDA power_out Internal analog voltage supply from the internal LDO; a capacitor CVA must be connected to GND, and no external voltage should be applied.
9 GND power_in Common ground connection.
10 VDD power_in External supply voltage (3.3V ±0.3V or 5.0V ±0.5V per Table 6); two parallel capacitors CVD must be connected to GND.
11 OUT1 output Buffered analog or digital output (COSN, REF_COS, or B_N depending on mode); diagnostic state indicates alarm status.
12 OUT2 output Buffered analog or digital output (COS or B depending on mode); diagnostic state indicates alarm status.
13 OUT3 output Buffered analog or digital output (SINN, REF_SIN, or A_N depending on mode); diagnostic state indicates alarm status.
14 OUT4 output Buffered analog or digital output (SIN or A depending on mode); diagnostic state indicates alarm status.
15 SCK_SCL input Clock input for the digital programming and diagnostic interface: SCL (external pull-up mandatory) in I2C mode or SCK (pull-up optional) in SPI mode.
16 SIO_SDA bidirectional Bidirectional data line for the digital programming and diagnostic interface: open-drain SDA with mandatory external pull-up in I2C mode or push-pull SIO with optional pull-up in SPI mode.

Key specifications

Parameter Value
Manufacturer RENESAS
Package TSSOP-16
Category Sensors
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External supply voltage (continuous) VVDDmax -18 7.5 V Continuous 7
Output voltage OUT1-OUT4, IC not supplied VOUT -18 7.5 V IC not supplied, permanent 7
Output voltage OUT1-OUT4, IC supplied VOUT -15 18 V IC supplied, permanent 7
Receiver coil pin voltage RX1-RX4 VRX1 -12 12 V Receiver coil pin: RX1, RX2, RX3, RX4 7
Digital IO pins voltage SCK_SCL, SIO_SDA, CSN_IRQN VDIGITAL -0.3 18 V Digital IO pins: SCK_SCL, SIO_SDA, CSN_IRQN 7
Ambient temperature 16-TSSOP TAMB_TSSOP -40 125 ºC 7
Junction temperature TJ -40 145 ºC 7
Storage temperature TSTOR -55 150 ºC Unmounted units must be limited to 10 hours at temperatures above 125°C 7
Thermal resistance junction to ambient 16-TSSOP RTHJA_TSSOP 89 ºC/W JEDEC MO-153 7
Start-up time tpup 3 ms Power-on reset (POR) to valid output signal 7
Input rotational velocity VEL 250000 rpm Electrical speed; Sine or cosine periods per minute 8
Power on reset high threshold VVDDA_TH_H 2.6 V The device is activated when VDDA increases above this threshold 8
Power on reset low threshold VVDDA_TH_L 2.1 V The device is deactivated when VDDA decreases below this threshold 8
Power-on reset hysteresis VDDAPOR_HYST 50 mV At VDDA pin 8
VDDA load current limitation IVDDA 75 mA 8
Current consumption without coils IDD 8.4 12 mA Without coils. no load 8
Capacitor from VDDA pin to GND CVA 100 nF 8
Capacitor from VDD pin to GND CVD 70 nF 8
Accuracy 3.3V mode, under-voltage alarm level to 3.0V INLUV3V -0.3 0.3 % FS With ideal coil input signals, relative to an output signal of 1.8Vpp 8
Accuracy 3.3V mode, VDD 3.0 to 3.6V INL3V -0.2 0.2 % FS 8
Accuracy 3.3V mode, VDD 3.6V to over-voltage alarm level INLOV3V -0.3 0.3 % FS 8
Accuracy 5V mode, under-voltage alarm level to 4.5V INLUV5V -0.3 0.3 % FS With ideal coil input signals, relative to an output signal of 3.0Vpp 8
Accuracy 5.0V mode, VDD 4.5 to 5.5V INL5V -0.2 0.2 % FS 8
Accuracy 5.0V mode, VDD 5.5V to over-voltage alarm level INLOV5V -0.3 0.3 % FS 8
Supply voltage 3.3V mode VDD3 3 3.3 3.6 V 9
Analog supply voltage 3.3V mode VDDA3 2.85 3 3.1 V Internally regulated. Connect a CVA = 100nF capacitor from VDDA to GND. 9
Over-voltage detection VDD rising 3.3V mode V3OVR 3.8 4.3 V An over-voltage alarm is created if VDD rises above these limits. 9
Over-voltage detection VDD falling 3.3V mode V3OVF 3.5 4.1 V An over-voltage alarm is cleared if VDD falls below these limits. 9
Over-voltage detection hysteresis 3.3V mode V3OVH 150 mV 9
Under-voltage detection VDD falling 3.3V mode V3UVR 2.2 2.95 V An under-voltage alarm is created if VDD falls below these limits. 9
Under-voltage detection VDD rising 3.3V mode V3UVF 2.6 3.1 V An under-voltage alarm is cleared if VDD rises above these limits. 9
Under-voltage detection hysteresis 3.3V mode V3UVH 100 mV 9
VDDA under-voltage detection falling 3.3V mode V3VDDAUVF 2.6 2.85 V An under-voltage alarm is created if VDDA falls below these limits. 9
VDDA under-voltage detection rising 3.3V mode V3VDDAUVRr 2.7 2.9 V An under-voltage alarm is created if VDDA rises above these limits. 9
Supply voltage 5.0V mode VDD5 4.5 5 5.5 V 9
Analog supply voltage 5.0V mode VDDA5 3.9 4 4.1 V Internally regulated. Connect a CVA = 100nF capacitor from VDDA to GND. 9
Over-voltage detection VDD rising 5V mode V5OVR 6.2 6.9 V An over-voltage alarm is created if VDD rises above these limits. 9
Over-voltage detection VDD falling 5V mode V5OVF 5.9 6.6 V An over-voltage alarm is cleared if VDD falls below these limits. 9
Over-voltage detection hysteresis 5V mode V5OVH 150 mV 9
Under-voltage detection VDD falling 5V mode V5UVR 3.8 4.4 V An under-voltage alarm is created if VDD falls below these limits. 9
Under-voltage detection VDD rising 5V mode V5UVF 4 4.6 V An under-voltage alarm is cleared if VDD rises above these limits. 9
Under-voltage detection hysteresis 5V mode V5UVH 100 mV 9
VDDA under-voltage detection falling 5V mode V5VDDAUVF 3.45 3.9 V A VDDA under-voltage alarm is triggered when VDDA falls below these limits. 9
VDDA under-voltage detection rising 5V mode V5VDDAUVRr 3.5 3.9 V A VDDA under-voltage alarm is cleared if VDDA rises above these limits. 9
Equivalent parallel resistance of the LC resonant circuit RP,eq 100 Ω See Equation 1 and Equation 2. 10
Excitation frequency fLC 1.7 5.8 MHz LC oscillator; determined by external components L and C. 10
Accuracy of transmitter oscillator frequency measurement FOSC_ACC -10 10 % Gated by the internal oscillator. 10
LC oscillator lower frequency diagnostics range fLC_DIAG_L 0.007 MHz Programmable frequency where an out-of-range frequency diagnostics alarm can be enabled. 10
LC oscillator upper frequency diagnostics range fLC_DIAG_H 10 MHz 10
LC oscillator amplitude VTX_P 11 Vpp Peak-to-peak voltage; pins TX1 vs. TX2; all modes. The coil current is user programmable. 10
Programmable transmitter coil drive current ILC 0 3 20 mA Equivalent DC current. Programmable, depending on transmitter coil inductance. 10
Maximum transmitter coil drive current tolerance ILCmax 18 20 22 mA At room temperature 10
TX series resistor RTx1,RTx2 22 Ω For reduced EMC emission, see Figure 13 to Figure 16 10

CAD (KiCad official)

  • Symbol: IPS2200BI1R
  • Footprint: Package_SO:TSSOP-16_4.4x5mm_P0.65mm
  • 3D model: TSSOP-16 (KiCad packages3D, STEP)
  • 3D model files: ips2200bi1r-etched.step / ips2200bi1r-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ips2200bi1r.step / ips2200bi1r.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (36 pp, sha256 c0c3c59af7fc6d3e, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF