3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownIPS2200BI1R
RENESAS · Position Sensor · TSSOP-16
IPS2200BI1R from RENESAS, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CSN_IRQN | bidirectional | Digital pin serving as chip-select input for the SPI interface (external pull-up required) or as push/pull interrupt output for the I2C or SPI interface, with programmable options per Table 3. |
| 2 | RX1 | input | Receiver coil 1 (sine) connects between the RX2 and RX1 pins. |
| 3 | RX2 | input | Receiver coil 1 (sine) connects between the RX2 and RX1 pins. |
| 4 | RX3 | input | Receiver coil 2 (cosine) connects between the RX4 and RX3 pins. |
| 5 | RX4 | input | Receiver coil 2 (cosine) connects between the RX4 and RX3 pins. |
| 6 | TX1 | bidirectional | Transmitter coil connects between TX1 and TX2; resonant frequency is set by a parallel capacitor CT or by capacitors CT1 (TX2 to GND) and CT2 (TX1 to GND). |
| 7 | TX2 | bidirectional | Transmitter coil connects between TX1 and TX2; resonant frequency is set by a parallel capacitor CT or by capacitors CT1 (TX2 to GND) and CT2 (TX1 to GND). |
| 8 | VDDA | power_out | Internal analog voltage supply from the internal LDO; a capacitor CVA must be connected to GND, and no external voltage should be applied. |
| 9 | GND | power_in | Common ground connection. |
| 10 | VDD | power_in | External supply voltage (3.3V ±0.3V or 5.0V ±0.5V per Table 6); two parallel capacitors CVD must be connected to GND. |
| 11 | OUT1 | output | Buffered analog or digital output (COSN, REF_COS, or B_N depending on mode); diagnostic state indicates alarm status. |
| 12 | OUT2 | output | Buffered analog or digital output (COS or B depending on mode); diagnostic state indicates alarm status. |
| 13 | OUT3 | output | Buffered analog or digital output (SINN, REF_SIN, or A_N depending on mode); diagnostic state indicates alarm status. |
| 14 | OUT4 | output | Buffered analog or digital output (SIN or A depending on mode); diagnostic state indicates alarm status. |
| 15 | SCK_SCL | input | Clock input for the digital programming and diagnostic interface: SCL (external pull-up mandatory) in I2C mode or SCK (pull-up optional) in SPI mode. |
| 16 | SIO_SDA | bidirectional | Bidirectional data line for the digital programming and diagnostic interface: open-drain SDA with mandatory external pull-up in I2C mode or push-pull SIO with optional pull-up in SPI mode. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TSSOP-16 |
| Category | Sensors |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External supply voltage (continuous) | VVDDmax | -18 | 7.5 | V | Continuous | 7 | |
| Output voltage OUT1-OUT4, IC not supplied | VOUT | -18 | 7.5 | V | IC not supplied, permanent | 7 | |
| Output voltage OUT1-OUT4, IC supplied | VOUT | -15 | 18 | V | IC supplied, permanent | 7 | |
| Receiver coil pin voltage RX1-RX4 | VRX1 | -12 | 12 | V | Receiver coil pin: RX1, RX2, RX3, RX4 | 7 | |
| Digital IO pins voltage SCK_SCL, SIO_SDA, CSN_IRQN | VDIGITAL | -0.3 | 18 | V | Digital IO pins: SCK_SCL, SIO_SDA, CSN_IRQN | 7 | |
| Ambient temperature 16-TSSOP | TAMB_TSSOP | -40 | 125 | ºC | 7 | ||
| Junction temperature | TJ | -40 | 145 | ºC | 7 | ||
| Storage temperature | TSTOR | -55 | 150 | ºC | Unmounted units must be limited to 10 hours at temperatures above 125°C | 7 | |
| Thermal resistance junction to ambient 16-TSSOP | RTHJA_TSSOP | 89 | ºC/W | JEDEC MO-153 | 7 | ||
| Start-up time | tpup | 3 | ms | Power-on reset (POR) to valid output signal | 7 | ||
| Input rotational velocity | VEL | 250000 | rpm | Electrical speed; Sine or cosine periods per minute | 8 | ||
| Power on reset high threshold | VVDDA_TH_H | 2.6 | V | The device is activated when VDDA increases above this threshold | 8 | ||
| Power on reset low threshold | VVDDA_TH_L | 2.1 | V | The device is deactivated when VDDA decreases below this threshold | 8 | ||
| Power-on reset hysteresis | VDDAPOR_HYST | 50 | mV | At VDDA pin | 8 | ||
| VDDA load current limitation | IVDDA | 75 | mA | 8 | |||
| Current consumption without coils | IDD | 8.4 | 12 | mA | Without coils. no load | 8 | |
| Capacitor from VDDA pin to GND | CVA | 100 | nF | 8 | |||
| Capacitor from VDD pin to GND | CVD | 70 | nF | 8 | |||
| Accuracy 3.3V mode, under-voltage alarm level to 3.0V | INLUV3V | -0.3 | 0.3 | % FS | With ideal coil input signals, relative to an output signal of 1.8Vpp | 8 | |
| Accuracy 3.3V mode, VDD 3.0 to 3.6V | INL3V | -0.2 | 0.2 | % FS | 8 | ||
| Accuracy 3.3V mode, VDD 3.6V to over-voltage alarm level | INLOV3V | -0.3 | 0.3 | % FS | 8 | ||
| Accuracy 5V mode, under-voltage alarm level to 4.5V | INLUV5V | -0.3 | 0.3 | % FS | With ideal coil input signals, relative to an output signal of 3.0Vpp | 8 | |
| Accuracy 5.0V mode, VDD 4.5 to 5.5V | INL5V | -0.2 | 0.2 | % FS | 8 | ||
| Accuracy 5.0V mode, VDD 5.5V to over-voltage alarm level | INLOV5V | -0.3 | 0.3 | % FS | 8 | ||
| Supply voltage 3.3V mode | VDD3 | 3 | 3.3 | 3.6 | V | 9 | |
| Analog supply voltage 3.3V mode | VDDA3 | 2.85 | 3 | 3.1 | V | Internally regulated. Connect a CVA = 100nF capacitor from VDDA to GND. | 9 |
| Over-voltage detection VDD rising 3.3V mode | V3OVR | 3.8 | 4.3 | V | An over-voltage alarm is created if VDD rises above these limits. | 9 | |
| Over-voltage detection VDD falling 3.3V mode | V3OVF | 3.5 | 4.1 | V | An over-voltage alarm is cleared if VDD falls below these limits. | 9 | |
| Over-voltage detection hysteresis 3.3V mode | V3OVH | 150 | mV | 9 | |||
| Under-voltage detection VDD falling 3.3V mode | V3UVR | 2.2 | 2.95 | V | An under-voltage alarm is created if VDD falls below these limits. | 9 | |
| Under-voltage detection VDD rising 3.3V mode | V3UVF | 2.6 | 3.1 | V | An under-voltage alarm is cleared if VDD rises above these limits. | 9 | |
| Under-voltage detection hysteresis 3.3V mode | V3UVH | 100 | mV | 9 | |||
| VDDA under-voltage detection falling 3.3V mode | V3VDDAUVF | 2.6 | 2.85 | V | An under-voltage alarm is created if VDDA falls below these limits. | 9 | |
| VDDA under-voltage detection rising 3.3V mode | V3VDDAUVRr | 2.7 | 2.9 | V | An under-voltage alarm is created if VDDA rises above these limits. | 9 | |
| Supply voltage 5.0V mode | VDD5 | 4.5 | 5 | 5.5 | V | 9 | |
| Analog supply voltage 5.0V mode | VDDA5 | 3.9 | 4 | 4.1 | V | Internally regulated. Connect a CVA = 100nF capacitor from VDDA to GND. | 9 |
| Over-voltage detection VDD rising 5V mode | V5OVR | 6.2 | 6.9 | V | An over-voltage alarm is created if VDD rises above these limits. | 9 | |
| Over-voltage detection VDD falling 5V mode | V5OVF | 5.9 | 6.6 | V | An over-voltage alarm is cleared if VDD falls below these limits. | 9 | |
| Over-voltage detection hysteresis 5V mode | V5OVH | 150 | mV | 9 | |||
| Under-voltage detection VDD falling 5V mode | V5UVR | 3.8 | 4.4 | V | An under-voltage alarm is created if VDD falls below these limits. | 9 | |
| Under-voltage detection VDD rising 5V mode | V5UVF | 4 | 4.6 | V | An under-voltage alarm is cleared if VDD rises above these limits. | 9 | |
| Under-voltage detection hysteresis 5V mode | V5UVH | 100 | mV | 9 | |||
| VDDA under-voltage detection falling 5V mode | V5VDDAUVF | 3.45 | 3.9 | V | A VDDA under-voltage alarm is triggered when VDDA falls below these limits. | 9 | |
| VDDA under-voltage detection rising 5V mode | V5VDDAUVRr | 3.5 | 3.9 | V | A VDDA under-voltage alarm is cleared if VDDA rises above these limits. | 9 | |
| Equivalent parallel resistance of the LC resonant circuit | RP,eq | 100 | Ω | See Equation 1 and Equation 2. | 10 | ||
| Excitation frequency | fLC | 1.7 | 5.8 | MHz | LC oscillator; determined by external components L and C. | 10 | |
| Accuracy of transmitter oscillator frequency measurement | FOSC_ACC | -10 | 10 | % | Gated by the internal oscillator. | 10 | |
| LC oscillator lower frequency diagnostics range | fLC_DIAG_L | 0.007 | MHz | Programmable frequency where an out-of-range frequency diagnostics alarm can be enabled. | 10 | ||
| LC oscillator upper frequency diagnostics range | fLC_DIAG_H | 10 | MHz | 10 | |||
| LC oscillator amplitude | VTX_P | 11 | Vpp | Peak-to-peak voltage; pins TX1 vs. TX2; all modes. The coil current is user programmable. | 10 | ||
| Programmable transmitter coil drive current | ILC | 0 | 3 | 20 | mA | Equivalent DC current. Programmable, depending on transmitter coil inductance. | 10 |
| Maximum transmitter coil drive current tolerance | ILCmax | 18 | 20 | 22 | mA | At room temperature | 10 |
| TX series resistor | RTx1,RTx2 | 22 | Ω | For reduced EMC emission, see Figure 13 to Figure 16 | 10 |
CAD (KiCad official)
- Symbol:
IPS2200BI1R - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
ips2200bi1r-etched.step/ips2200bi1r-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ips2200bi1r.step/ips2200bi1r.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (36 pp, sha256
c0c3c59af7fc6d3e, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).