Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TDA7293V

STMicroelectronics · Audio Amplifiers · MultiwAtt-15

TDA7293V from STMicroelectronics, in a MultiwAtt-15. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 STAND-BY GND power_in Stand-by ground; the stand-by and mute thresholds are referenced to this pin, and its voltage is limited to 90 V referred to -VS.
2 INVERTING INPUT input Inverting input; limited to 90 V referred to -VS and to ±30 V differential against the non-inverting input.
3 NON INVERTING INPUT input Non-inverting input; limited to 90 V referred to -VS, and in slave devices this input is connected to the negative supply.
4 SIGNAL GROUND power_in Signal ground, limited to 90 V referred to -VS; it also sets the slave/master function, where at or below -VS+1 V it selects slave and at or above -VS+3 V it selects master.
5 CLIP AND SHORT CIRCUIT DETECTOR output Clip and short-circuit detector output, limited to 120 V referred to -VS and used with a pull-up resistor (for example 10 kΩ to 5 V).
6 BOOTSTRAP passive Bootstrap capacitor connection (to OUT pin 14 or to bootstrap loader pin 12), limited to 120 V referred to -VS.
7 +VS (SIGNAL) power_in Positive supply for the signal part; supply range is ±12 V to ±50 V.
8 -VS (SIGNAL) power_in Negative supply for the signal part, the reference for the absolute maximum voltages, connected to the tab.
9 STAND-BY input Stand-by control input, CMOS logic compatible, with on threshold of 1.5 V max and off threshold of 3.5 V min referred to pin 1, and limited to 120 V referred to -VS.
10 MUTE input Mute control input, CMOS logic compatible, with on threshold of 1.5 V max and off threshold of 3.5 V min referred to pin 1, and limited to 120 V referred to -VS.
11 BUFFER DRIVER bidirectional Buffer driver pin used only for modular (parallel) connection of devices, limited to 120 V referred to -VS.
12 BOOTSTRAP LOADER passive Bootstrap loader that follows the output voltage up to 100 V and is clamped at 100 V above that, allowing a maximum supply voltage of 120 V when the bootstrap capacitor is connected to pin 6.
13 +VS (POWER) power_in Positive supply for the power stage, which can be bootstrapped in high-efficiency applications; supply range is ±12 V to ±50 V.
14 OUT output Power amplifier output with 10 A peak output current limit and current limiter threshold of 6.5 A typ at VS up to ±40 V.
15 -VS (POWER) power_in Negative supply for the power stage, which can be bootstrapped in high-efficiency applications; supply range is ±12 V to ±50 V.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package MultiwAtt-15
Category Amplifiers/Comparators
Pins 15

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply range VS 12 50 V 5
Quiescent current Iq 50 100 mA 5
Input bias current Ib 0.3 1 µA 5
Input offset voltage VOS -10 10 mV 5
Input offset current IOS 0.2 µA 5
Continuous output power PO 75 80 W d = 1%, RL = 4 Ω, VS = ±29 V 5
Continuous output power PO 90 100 W d = 10%, RL = 4Ω, VS = ±29 V 5
Total harmonic distortion d 0.1 % PO = 0.1 to 50 W, f = 20 Hz to 15 kHz 5
Slew rate SR 5 10 V/µs 5
Closed loop voltage gain GV 29 30 31 dB 5
Total input noise eN 3 10 µV f = 20 Hz to 20 kHz 5
Input resistance Ri 100 kΩ 5
Standby on threshold VST on 1.5 V 5
Standby off threshold VST off 3.5 V 5
Standby attenuation ATTst-by 70 90 dB 5
Quiescent current @ standby Iq st-by 0.5 1 mA 5
Mute on threshold VMon 1.5 V 5
Mute off threshold VMoff 3.5 V 5
Mute attenuation ATTmute 60 80 dB 5
Duty cycle (pin 5) Duty 30 40 50 % d = 10%, RPULLUP = 10 kΩ to 5 V 6
Clip detector leakage current ICLEAK 3 µA PO = 50 W 6
Slave threshold (pin 4, ref. pin 8) VSlave 1 V 6
Master threshold (pin 4, ref. pin 8) VMaster 3 V 6
Supply voltage (no signal) VS -60 60 V no signal 4
VSTANDBY GND voltage referred to -VS (pin 8) V1 90 V 4
Input voltage (inverting) referred to -VS V2 90 V 4
Maximum differential inputs V2 - V3 -30 30 V 4
Input voltage (non inverting) referred to -VS V3 90 V 4
Signal GND voltage referred to -VS V4 90 V 4
Clip detector voltage referred to -VS V5 120 V 4
Bootstrap voltage referred to -VS V6 120 V 4
Standby voltage referred to -VS V9 120 V 4
Mute voltage referred to -VS V10 120 V 4
Buffer voltage referred to -VS V11 120 V 4
Bootstrap loader voltage referred to -VS V12 100 V 4
Output peak current IO 10 A 4
Power dissipation Ptot 50 W Tcase = 70°C 4
Storage and junction temperature Tstg, Tj 150 °C 4
ESD maximum withstanding voltage (HBM) VESD_HBM -1500 1500 V CDF-AEC-Q100-002 human body model 4
Operating ambient temperature range Top 0 70 °C 4
Thermal resistance junction to case Rthj-case 1 1.5 °C/W 4

CAD (Adom-generated)

  • Symbol: TDA7293V
  • Footprint: Adom_Gen:STMicroelectronics_TDA7293
  • 3D model: generated to fit the land (STEP)
  • 3D model files: tda7293v-etched.step / tda7293v-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tda7293v.step / tda7293v.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (21 pp, sha256 fd1710e573ad0bf3, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.

Datasheet PDF