component
TDA7293V
Public Made by Adomby adom
STMicroelectronics Audio Amplifiers, MultiwAtt-15. Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.
Generated by adom_assets · KiCad file format 20240108
TDA7293V
STMicroelectronics · Audio Amplifiers · MultiwAtt-15
TDA7293V from STMicroelectronics, in a MultiwAtt-15. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | STAND-BY GND | power_in | Stand-by ground; the stand-by and mute thresholds are referenced to this pin, and its voltage is limited to 90 V referred to -VS. |
| 2 | INVERTING INPUT | input | Inverting input; limited to 90 V referred to -VS and to ±30 V differential against the non-inverting input. |
| 3 | NON INVERTING INPUT | input | Non-inverting input; limited to 90 V referred to -VS, and in slave devices this input is connected to the negative supply. |
| 4 | SIGNAL GROUND | power_in | Signal ground, limited to 90 V referred to -VS; it also sets the slave/master function, where at or below -VS+1 V it selects slave and at or above -VS+3 V it selects master. |
| 5 | CLIP AND SHORT CIRCUIT DETECTOR | output | Clip and short-circuit detector output, limited to 120 V referred to -VS and used with a pull-up resistor (for example 10 kΩ to 5 V). |
| 6 | BOOTSTRAP | passive | Bootstrap capacitor connection (to OUT pin 14 or to bootstrap loader pin 12), limited to 120 V referred to -VS. |
| 7 | +VS (SIGNAL) | power_in | Positive supply for the signal part; supply range is ±12 V to ±50 V. |
| 8 | -VS (SIGNAL) | power_in | Negative supply for the signal part, the reference for the absolute maximum voltages, connected to the tab. |
| 9 | STAND-BY | input | Stand-by control input, CMOS logic compatible, with on threshold of 1.5 V max and off threshold of 3.5 V min referred to pin 1, and limited to 120 V referred to -VS. |
| 10 | MUTE | input | Mute control input, CMOS logic compatible, with on threshold of 1.5 V max and off threshold of 3.5 V min referred to pin 1, and limited to 120 V referred to -VS. |
| 11 | BUFFER DRIVER | bidirectional | Buffer driver pin used only for modular (parallel) connection of devices, limited to 120 V referred to -VS. |
| 12 | BOOTSTRAP LOADER | passive | Bootstrap loader that follows the output voltage up to 100 V and is clamped at 100 V above that, allowing a maximum supply voltage of 120 V when the bootstrap capacitor is connected to pin 6. |
| 13 | +VS (POWER) | power_in | Positive supply for the power stage, which can be bootstrapped in high-efficiency applications; supply range is ±12 V to ±50 V. |
| 14 | OUT | output | Power amplifier output with 10 A peak output current limit and current limiter threshold of 6.5 A typ at VS up to ±40 V. |
| 15 | -VS (POWER) | power_in | Negative supply for the power stage, which can be bootstrapped in high-efficiency applications; supply range is ±12 V to ±50 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | MultiwAtt-15 |
| Category | Amplifiers/Comparators |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply range | VS | 12 | 50 | V | 5 | ||
| Quiescent current | Iq | 50 | 100 | mA | 5 | ||
| Input bias current | Ib | 0.3 | 1 | µA | 5 | ||
| Input offset voltage | VOS | -10 | 10 | mV | 5 | ||
| Input offset current | IOS | 0.2 | µA | 5 | |||
| Continuous output power | PO | 75 | 80 | W | d = 1%, RL = 4 Ω, VS = ±29 V | 5 | |
| Continuous output power | PO | 90 | 100 | W | d = 10%, RL = 4Ω, VS = ±29 V | 5 | |
| Total harmonic distortion | d | 0.1 | % | PO = 0.1 to 50 W, f = 20 Hz to 15 kHz | 5 | ||
| Slew rate | SR | 5 | 10 | V/µs | 5 | ||
| Closed loop voltage gain | GV | 29 | 30 | 31 | dB | 5 | |
| Total input noise | eN | 3 | 10 | µV | f = 20 Hz to 20 kHz | 5 | |
| Input resistance | Ri | 100 | kΩ | 5 | |||
| Standby on threshold | VST on | 1.5 | V | 5 | |||
| Standby off threshold | VST off | 3.5 | V | 5 | |||
| Standby attenuation | ATTst-by | 70 | 90 | dB | 5 | ||
| Quiescent current @ standby | Iq st-by | 0.5 | 1 | mA | 5 | ||
| Mute on threshold | VMon | 1.5 | V | 5 | |||
| Mute off threshold | VMoff | 3.5 | V | 5 | |||
| Mute attenuation | ATTmute | 60 | 80 | dB | 5 | ||
| Duty cycle (pin 5) | Duty | 30 | 40 | 50 | % | d = 10%, RPULLUP = 10 kΩ to 5 V | 6 |
| Clip detector leakage current | ICLEAK | 3 | µA | PO = 50 W | 6 | ||
| Slave threshold (pin 4, ref. pin 8) | VSlave | 1 | V | 6 | |||
| Master threshold (pin 4, ref. pin 8) | VMaster | 3 | V | 6 | |||
| Supply voltage (no signal) | VS | -60 | 60 | V | no signal | 4 | |
| VSTANDBY GND voltage referred to -VS (pin 8) | V1 | 90 | V | 4 | |||
| Input voltage (inverting) referred to -VS | V2 | 90 | V | 4 | |||
| Maximum differential inputs | V2 - V3 | -30 | 30 | V | 4 | ||
| Input voltage (non inverting) referred to -VS | V3 | 90 | V | 4 | |||
| Signal GND voltage referred to -VS | V4 | 90 | V | 4 | |||
| Clip detector voltage referred to -VS | V5 | 120 | V | 4 | |||
| Bootstrap voltage referred to -VS | V6 | 120 | V | 4 | |||
| Standby voltage referred to -VS | V9 | 120 | V | 4 | |||
| Mute voltage referred to -VS | V10 | 120 | V | 4 | |||
| Buffer voltage referred to -VS | V11 | 120 | V | 4 | |||
| Bootstrap loader voltage referred to -VS | V12 | 100 | V | 4 | |||
| Output peak current | IO | 10 | A | 4 | |||
| Power dissipation | Ptot | 50 | W | Tcase = 70°C | 4 | ||
| Storage and junction temperature | Tstg, Tj | 150 | °C | 4 | |||
| ESD maximum withstanding voltage (HBM) | VESD_HBM | -1500 | 1500 | V | CDF-AEC-Q100-002 human body model | 4 | |
| Operating ambient temperature range | Top | 0 | 70 | °C | 4 | ||
| Thermal resistance junction to case | Rthj-case | 1 | 1.5 | °C/W | 4 |
CAD (Adom-generated)
- Symbol:
TDA7293V - Footprint:
Adom_Gen:STMicroelectronics_TDA7293 - 3D model: generated to fit the land (STEP)
- 3D model files:
tda7293v-etched.step/tda7293v-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tda7293v.step/tda7293v.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (21 pp, sha256
fd1710e573ad0bf3, retrieved 2026-11-05, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.