3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownKSZ8864CNXCA
Microchip Tech · Ethernet ICs · QFN-64(8x8)
KSZ8864CNXCA from Microchip Tech, in a QFN-64(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RXP1 | input | Port 1 physical receive signal + (differential). |
| 2 | RXM1 | input | Port 1 physical receive signal - (differential). |
| 3 | TXP1 | output | Port 1 physical transmit signal + (differential). |
| 4 | TXM1 | output | Port 1 physical transmit signal - (differential). |
| 5 | VDDA12 | power_in | 1.2V analog power supply. |
| 6 | GND | power_in | Ground, with all grounding of die bottom. |
| 7 | ISET | passive | Sets physical transmit output current; pull down with a 12.4 kΩ 1% resistor. |
| 8 | VDDAT | power_in | 3.3V analog VDD. |
| 9 | RXP2 | input | Port 2 physical receive signal + (differential). |
| 10 | RXM2 | input | Port 2 physical receive signal - (differential). |
| 11 | TXP2 | output | Port 2 physical transmit signal + (differential). |
| 12 | TXM2 | output | Port 2 physical transmit signal - (differential). |
| 13 | VDDAT | power_in | 3.3V analog VDD. |
| 14 | INTR_N | output | Interrupt, open-drain output pin. |
| 15 | VDDC | power_in | 1.2V digital core VDD. |
| 16 | SM3TXEN | input | MAC3 switch MII/RMII transmit enable (internal pull-down). |
| 17 | SM3TXD3 | input | MAC3 switch MII transmit bit 3 (internal pull-down). |
| 18 | SM3TXD2 | input | MAC3 switch MII transmit bit 2 (internal pull-down). |
| 19 | SM3TXD1 | input | MAC3 switch MII/RMII transmit bit 1 (internal pull-down). |
| 20 | SM3TXD0 | input | MAC3 switch MII/RMII transmit bit 0 (internal pull-down). |
| 21 | SM3TXC/SM3REFCLK | bidirectional | MAC3 MII transmit clock: input in SW3-MII MAC mode, output in PHY mode, input as SW3-RMII reference clock. |
| 22 | VDDIO | power_in | 3.3V, 2.5V, or 1.8V digital VDD for digital I/O circuitry. |
| 23 | SM3RXC | bidirectional | MAC3 MII receive clock: input in SW3-MII MAC mode, output in PHY mode, output as SW3-RMII reference clock; unused RMII clock can be pulled down or disabled by Register 87. |
| 24 | SM3RXDV/SM3CRSDV | bidirectional | SM3RXDV: MAC3 SW3-MII receive data valid; SM3CRSDV: SW3-RMII carrier sense/receive data valid. |
| 25 | SM3RXD3 | bidirectional | MAC3 MII receive bit 3; strap: PD (default) = enable flow control, PU = disable flow control. |
| 26 | SM3RXD2 | bidirectional | MAC3 MII receive bit 2; strap: PD (default) = disable back pressure, PU = enable back pressure. |
| 27 | SM3RXD1 | bidirectional | MAC3 MII/RMII receive bit 1; strap: PD (default) = drop excessive collision packets, PU = do not drop them. |
| 28 | SM3RXD0 | bidirectional | MAC3 MII/RMII receive bit 0; strap: PD (default) = disable aggressive back-off in half-duplex, PU = enable for performance enhancement. |
| 29 | SM3CRS | bidirectional | MAC3 switch MII carrier sense. |
| 30 | GND | power_in | Ground, with all grounding of die bottom. |
| 31 | SM3COL | bidirectional | MAC3 switch MII collision detect. |
| 32 | SM4TXEN | input | MAC4 switch MII/RMII transmit enable (internal pull-down). |
| 33 | SM4TXD3 | input | MAC4 switch MII transmit bit 3 (internal pull-down). |
| 34 | SM4TXD2 | input | MAC4 switch MII transmit bit 2 (internal pull-down). |
| 35 | SM4TXD1 | input | MAC4 switch MII/RMII transmit bit 1 (internal pull-down). |
| 36 | SM4TXD0 | input | MAC4 switch MII/RMII transmit bit 0 (internal pull-down). |
| 37 | SM4TXC/SM4REFCLK | bidirectional | MAC4 MII transmit clock: input in SW4-MII MAC mode, output in PHY mode, input as SW4-RMII reference clock (clock/normal mode set by strap P1LED1). |
| 38 | VDDIO | power_in | 3.3V, 2.5V, or 1.8V digital VDD for digital I/O circuitry. |
| 39 | SM4RXC | bidirectional | MAC4 MII receive clock: input in MAC mode, output in PHY mode, output as SW4-RMII 50 MHz reference clock (disable by Register 87 in normal mode). |
| 40 | SM4RXDV/SM4CRSDV | bidirectional | SM4RXDV: MAC4 SW4-MII receive data valid; SM4CRSDV: SW4-RMII carrier sense/receive data valid. |
| 41 | SM4RXD3 | bidirectional | MAC4 MII receive bit 3; strap: PD (default) = disable switch MII/RMII full-duplex flow control, PU = enable. |
| 42 | SM4RXD2 | bidirectional | MAC4 MII receive bit 2; strap: PD (default) = full-duplex, PU = half-duplex. |
| 43 | SM4RXD1 | bidirectional | MAC4 MII/RMII receive bit 1; strap: PD (default) = 100 Mbps mode, PU = 10 Mbps mode. |
| 44 | SM4RXD0 | bidirectional | MAC4 MII/RMII receive bit 0; strap LED mode: PD (default) = mode 0, PU = mode 1. |
| 45 | SM4COL | bidirectional | MAC4 MII collision detect: input in SW4-MII MAC mode, output in PHY mode. |
| 46 | SM4CRS | bidirectional | MAC4 MII carrier sense: input in SW4-MII MAC mode, output in PHY mode. |
| 47 | SCONF1 | input | With SCONF0 selects port 4 mode: 00 (default) SW4-MII PHY mode, 01 disable ports 3 and 4, 10 disable port 4 only, 11 MAC mode (internal pull-down). |
| 48 | SCONF0 | input | Strap pin configured together with SCONF1 (pin 47) for port 4 MII PHY/MAC mode selection (internal pull-down). |
| 49 | P2LED1 | bidirectional | Port 2 LED indicator; must be pulled down by a 1 kΩ resistor for this device. |
| 50 | P2LED0 | bidirectional | Port 2 LED indicator; strap for MAC3: PU (default) = MII, PD = RMII. |
| 51 | P1LED1 | bidirectional | Port 1 LED indicator; strap for RMII: PU (default) = clock mode from 25 MHz crystal, PD = normal mode with 50 MHz input on SM4TXC. |
| 52 | P1LED0 | bidirectional | Port 1 LED indicator; strap for MAC4: PU (default) = MII, PD = RMII. |
| 53 | MDC | input | MII management (SMI) interface clock (internal pull-up). |
| 54 | MDIO | bidirectional | MII management (SMI) data I/O; needs external pull-up when driven. |
| 55 | SPIQ | bidirectional | SPI serial data output in SPI slave mode; needs external pull-up when driven. |
| 56 | SPIC/SCL | bidirectional | Input clock up to 25 MHz in SPI slave mode; output clock at 61 kHz in I2C master mode; needs external pull-up when driven. |
| 57 | SPID/SDA | bidirectional | Serial data input in SPI slave mode; data input/output in I2C master mode; needs external pull-up when driven. |
| 58 | SPIS_N | input | Active-low SPI slave select/transfer start (high deselects and holds SPIQ high-impedance); not used in I2C master mode. |
| 59 | PS1 | input | Serial bus configuration with PS0: 00 I2C master for EEPROM, 01 SMI, 10 SPI slave, 11 factory test (BIST). |
| 60 | PS0 | input | Serial bus configuration pin, used with PS1 (internal pull-down). |
| 61 | RST_N | input | Active-low device reset (internal pull-up). |
| 62 | VDDC | power_in | 1.2V digital core VDD. |
| 63 | X1 | input | 25 MHz crystal connection or 3.3V oscillator input; tolerance ≤ ±50 ppm. |
| 64 | X2 | output | 25 MHz crystal clock connection. |
| 65 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-64(8x8) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 65 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage VDDAR, VDDC | -0.5 | 2.4 | V | VDDAR, VDDC | 78 | ||
| Supply Voltage VDDAT, VDDIO | -0.5 | 4 | V | VDDAT, VDDIO | 78 | ||
| Input Voltage | -0.5 | 4 | V | 78 | |||
| Output Voltage | -0.5 | 4 | V | 78 | |||
| Lead Temperature | 260 | °C | soldering, 10s | 78 | |||
| Storage Temperature | TS | -55 | 150 | °C | 78 | ||
| HBM ESD Rating | 5 | kV | Human body model, 1.5 kΩ in series with 100 pF | 78 | |||
| Operating Supply Voltage VDDAR, VDDC | 1.14 | 1.26 | V | VDDAR, VDDC | 78 | ||
| Operating Supply Voltage VDDAT | 3.135 | 3.465 | V | VDDAT | 78 | ||
| Operating Supply Voltage VDDIO @ 3.3V | 3.135 | 3.465 | V | VDDIO @ 3.3V | 78 | ||
| Operating Supply Voltage VDDIO @ 2.5V | 2.375 | 2.625 | V | VDDIO @ 2.5V | 78 | ||
| Operating Supply Voltage VDDIO @ 1.8V | 1.71 | 1.89 | V | VDDIO @ 1.8V | 78 | ||
| Ambient Temperature Commercial | TA | 0 | 70 | °C | Commercial | 78 | |
| Maximum Junction Temperature | TJ max | 125 | °C | 78 | |||
| Thermal Resistance Junction to Ambient | ΘJA | 31.96 | °C/W | No heat spreader, air velocity 0 m/s | 78 | ||
| Thermal Resistance Junction to Case | ΘJC | 13.54 | °C/W | No heat spreader, air velocity 0 m/s | 78 | ||
| Input High Voltage | VIH | 2 | V | VDDIO = 3.3V (printed 2.0/1.8/1.3 for 3.3/2.5/1.8V) | 79 | ||
| Input Low Voltage | VIL | 0.8 | V | VDDIO = 3.3V (printed 0.8/0.7/0.5 for 3.3/2.5/1.8V) | 79 | ||
| Input Current (Excluding Pull-Up/Pull-Down) | IIN | -10 | 10 | µA | VIN = GND ~ VDDIO | 79 | |
| Output High Voltage | VOH | 2.4 | V | IOH = -8 mA; VDDIO = 3.3V (printed 2.4/2.0/1.5 for 3.3/2.5/1.8V) | 79 | ||
| Output Low Voltage | VOL | 0.4 | V | IOL = 8 mA; VDDIO = 3.3V (printed 0.4/0.4/0.3 for 3.3/2.5/1.8V) | 80 | ||
| Output Tri-State Leakage | IOZ | 10 | µA | VIN = GND ~ VDDIO | 80 | ||
| 100BASE-TX Peak Differential Output Voltage | VO | 0.95 | 1.05 | V | 100Ω termination on the differential output | 80 | |
| 100BASE-TX Output Voltage Imbalance | VIMB | 2 | % | 100Ω termination on the differential output | 80 | ||
| 100BASE-TX Rise/Fall Time | tr/tf | 3 | 5 | ns | 80 | ||
| 100BASE-TX Rise/Fall Time Imbalance | 0 | 0.5 | ns | 80 | |||
| 100BASE-TX Duty Cycle Distortion | -0.5 | 0.5 | ns | 80 | |||
| 100BASE-TX Overshoot | 5 | % | 80 | ||||
| 100BASE-TX Output Jitters | 0 | 0.75 | 1.4 | ns | Peak-to-Peak | 80 | |
| 10BASE-T Receive Squelch Threshold | VSQ | 300 | 400 | 585 | mV | 5 MHz square wave | 80 |
| 10BASE-T Transmit Peak Differential Output Voltage | VP | 2.2 | 2.5 | 2.8 | V | 100Ω termination on the differential output | 80 |
| 10BASE-T Transmit Output Jitters | 1.4 | 3.5 | ns | Peak-to-Peak | 80 | ||
| 10BASE-T Transmit Rise/Fall Times | 28 | 30 | ns | 80 | |||
| EEPROM Setup time | tS1 | 20 | ns | 81 | |||
| EEPROM Hold time | tH1 | 20 | ns | 81 | |||
| EEPROM Output valid | tOV1 | 4096 | 4112 | 4128 | ns | 81 | |
| EEPROM Clock cycle | tCYC1 | 16384 | ns | 81 | |||
| 100BASE-TX 3.3V Analog Current | IDX | 38 | mA | VDDAT; 100% utilization all ports | 79 | ||
| 100BASE-TX 1.2V Analog Current | IDda | 13 | mA | VDDAR | 79 | ||
| 100BASE-TX 1.2V Digital Current | IDDc | 41 | mA | VDDC | 79 | ||
| 100BASE-TX Digital IO 3.3V Current | IDDIO | 27 | mA | VDDIO (SW3/4-MII/RMII) | 79 | ||
| 10BASE-T 3.3V Analog Current | IDX | 48 | mA | VDDAT; 100% utilization all ports | 79 | ||
| 10BASE-T 1.2V Analog Current | IDda | 8 | mA | VDDAR | 79 | ||
| 10BASE-T 1.2V Digital Current | IDDc | 41 | mA | VDDC | 79 | ||
| 10BASE-T Digital IO 3.3V Current | IDDIO | 28 | mA | VDDIO (SW3/4-MII/RMII) | 79 | ||
| Auto-Negotiation 3.3V Analog Current | IDX | 25 | mA | VDDAT | 79 | ||
| Auto-Negotiation 1.2V Analog Current | IDda | 13 | mA | VDDAR | 79 | ||
| Auto-Negotiation 1.2V Digital Current | IEDM | 42 | mA | VDDC | 79 | ||
| Auto-Negotiation Digital IO 3.3V Current | IDDIO | 28 | mA | VDDIO (SW3/4-MII/RMII) | 79 | ||
| Power-Saving mode 3.3V Current | IPSM1 | 45 | mA | VDDAT + VDDIO | 79 | ||
| Power-Saving mode 1.2V Current | IPSM2 | 49 | mA | VDDAR + VDDC | 79 | ||
| Soft Power-Down mode 3.3V Current | ISPDM1 | 15 | mA | VDDAT + VDDIO | 79 | ||
| Soft Power-Down mode 1.2V Current | ISPDM2 | 1 | mA | VDDAR + VDDC | 79 | ||
| Energy-Detect mode + PLL Off 3.3V Current | IEDM1 | 35 | mA | VDDAT + VDDIO | 79 | ||
| Energy-Detect mode + PLL Off 1.2V Current | IEDM2 | 44 | mA | VDDAR + VDDC | 79 | ||
| Crystal Frequency | 25 | MHz | Reference crystal, tolerance ≤ ±50 ppm | 90 |
CAD (KiCad official)
- Symbol:
KSZ8864CNXCA - Footprint:
Package_DFN_QFN:QFN-64-1EP_8x8mm_P0.4mm_EP6.5x6.5mm - 3D model: QFN-64(8x8) (KiCad packages3D, STEP)
- 3D model files:
ksz8864cnxca-etched.step/ksz8864cnxca-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ksz8864cnxca.step/ksz8864cnxca.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (98 pp, sha256
00c8886e1e293e06, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).