Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

X9511WSIZT1

Intersil(Renesas Electronics) · Digital Potentiometers · SOIC-8

X9511WSIZT1 from Intersil(Renesas Electronics), in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VH/RH passive High terminal of the 31-resistor array, equivalent to the fixed high end of a mechanical potentiometer, with a voltage range of -5V to +5V.
2 PU input Debounced push-up input for incrementing the wiper, with an on-chip pull-up holding it HIGH; a LOW (VIL max 0.8V) or switch closure to ground moves the wiper to the next higher tap after debounce.
3 PD input Debounced push-down input for decrementing the wiper, with an on-chip pull-up holding it HIGH; a LOW (VIL max 0.8V) or switch closure to ground moves the wiper to the next lower tap after debounce.
4 VSS power_in Ground reference for the device.
5 VW/RW passive Wiper terminal that outputs the voltage at the currently selected one of the 32 tap points.
6 VL/RL passive Low terminal of the resistor array, equivalent to the fixed low end of a mechanical potentiometer, with a voltage range of -5V to +5V.
7 ASE input AUTOSTORE enable input: VIL enables AUTOSTORE so the wiper position is stored on VCC power-down, while VIH disables it and a LOW-to-HIGH transition starts a manual store (ASE input HIGH level minimum 2V, LOW maximum 0.8V).
8 VCC power_in Supply voltage of 5V ±10% per the recommended operating conditions (ICC active current max 3 mA).

Key specifications

Parameter Value
Manufacturer Intersil(Renesas Electronics)
Package SOIC-8
Category Data Converters
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Temperature under bias -65 135 °C 5
Storage temperature -65 150 °C 5
Voltage on PU, PD, and VCC with respect to VSS -1 7 V 5
Voltage on VH and VL referenced to VSS -8 8 V 5
Lead temperature 300 °C Soldering 10 seconds 5
Wiper current 1 mA 5
ESD Human Body Model 2.5 kV Per MIL-STD-883 Method 3015.7 5
ESD Machine Model 250 V Per EIAJ ED-4701 Method C-111 5
Rated voltage across array, V = /VH - VL/ 10 V X9511W 5
Power rating 10 mW At +25C, X9511W 5
End-to-end resistance tolerance -20 20 % 5
Absolute linearity -1 1 MI Maximum, per note (1) 5
Relative linearity 0.2 MI Per note (3) 5
Wiper position store operations 100000 data changes 5
Typical noise -120 dB/Hz Ref: 1V 5
Operating temperature range (industrial) -40 85 °C Industrial (X9511WSI) 6
Supply voltage tolerance VCC -10 10 % X9511 supply voltage 5V +/- 10% 6
VCC power-up rate tR 0.2 50 V/ms 6
VCC active current ICC 1 3 mA PU or PD held at VIL, the other at VIH 6
Standby supply current ISB 100 500 µA PU = PD = VIH 6
PU, PD, ASE input leakage current ILI 10 µA VIN = VSS to VCC 6
PU, PD, ASE input HIGH voltage VIH 2 V 6
PU, PD, ASE input LOW voltage VIL 0.8 V 6
Wiper resistance RW 40 100 Ω Wiper current VCC/RTOT 6
VH terminal voltage VVH -5 5 V 6
VL terminal voltage VVL -5 5 V 6
Time between two separate push button events tGAP 50 µs 6
Debounce time tDB 30 40 ms 6
Wiper change on slow mode after debounce tS SLOW 100 250 375 ms After debounce 6
Wiper change on fast mode tS FAST 25 50 90 ms 6
Power-up to wiper stable tPU 500 µs 6
AUTOSTORE cycle time tASTO 2 ms 6
AUTOSTORE threshold voltage VASTH 4 V 6
AUTOSTORE cycle end voltage VASEND 3.5 V 6
End-to-end temperature coefficient (X9511W) 300 ppm/°C -40C to +85C, typical 5
Ratiometric temperature coefficient 20 ppm 5
End-to-end resistance (RTOTAL, X9511W) RTOTAL 10 k 1
Supply voltage VCC (nominal) VCC 5 V 6

CAD (KiCad official)

  • Symbol: X9511WSIZT1
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: x9511wsizt1-etched.step / x9511wsizt1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); x9511wsizt1.step / x9511wsizt1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Intersil(Renesas Electronics) datasheet (9 pp, sha256 1c197dfbdde9eaa3, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF