3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownX9511WSIZT1
Intersil(Renesas Electronics) · Digital Potentiometers · SOIC-8
X9511WSIZT1 from Intersil(Renesas Electronics), in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VH/RH | passive | High terminal of the 31-resistor array, equivalent to the fixed high end of a mechanical potentiometer, with a voltage range of -5V to +5V. |
| 2 | PU | input | Debounced push-up input for incrementing the wiper, with an on-chip pull-up holding it HIGH; a LOW (VIL max 0.8V) or switch closure to ground moves the wiper to the next higher tap after debounce. |
| 3 | PD | input | Debounced push-down input for decrementing the wiper, with an on-chip pull-up holding it HIGH; a LOW (VIL max 0.8V) or switch closure to ground moves the wiper to the next lower tap after debounce. |
| 4 | VSS | power_in | Ground reference for the device. |
| 5 | VW/RW | passive | Wiper terminal that outputs the voltage at the currently selected one of the 32 tap points. |
| 6 | VL/RL | passive | Low terminal of the resistor array, equivalent to the fixed low end of a mechanical potentiometer, with a voltage range of -5V to +5V. |
| 7 | ASE | input | AUTOSTORE enable input: VIL enables AUTOSTORE so the wiper position is stored on VCC power-down, while VIH disables it and a LOW-to-HIGH transition starts a manual store (ASE input HIGH level minimum 2V, LOW maximum 0.8V). |
| 8 | VCC | power_in | Supply voltage of 5V ±10% per the recommended operating conditions (ICC active current max 3 mA). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Intersil(Renesas Electronics) |
| Package | SOIC-8 |
| Category | Data Converters |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Temperature under bias | -65 | 135 | °C | 5 | |||
| Storage temperature | -65 | 150 | °C | 5 | |||
| Voltage on PU, PD, and VCC with respect to VSS | -1 | 7 | V | 5 | |||
| Voltage on VH and VL referenced to VSS | -8 | 8 | V | 5 | |||
| Lead temperature | 300 | °C | Soldering 10 seconds | 5 | |||
| Wiper current | 1 | mA | 5 | ||||
| ESD Human Body Model | 2.5 | kV | Per MIL-STD-883 Method 3015.7 | 5 | |||
| ESD Machine Model | 250 | V | Per EIAJ ED-4701 Method C-111 | 5 | |||
| Rated voltage across array, V = /VH - VL/ | 10 | V | X9511W | 5 | |||
| Power rating | 10 | mW | At +25C, X9511W | 5 | |||
| End-to-end resistance tolerance | -20 | 20 | % | 5 | |||
| Absolute linearity | -1 | 1 | MI | Maximum, per note (1) | 5 | ||
| Relative linearity | 0.2 | MI | Per note (3) | 5 | |||
| Wiper position store operations | 100000 | data changes | 5 | ||||
| Typical noise | -120 | dB/Hz | Ref: 1V | 5 | |||
| Operating temperature range (industrial) | -40 | 85 | °C | Industrial (X9511WSI) | 6 | ||
| Supply voltage tolerance | VCC | -10 | 10 | % | X9511 supply voltage 5V +/- 10% | 6 | |
| VCC power-up rate | tR | 0.2 | 50 | V/ms | 6 | ||
| VCC active current | ICC | 1 | 3 | mA | PU or PD held at VIL, the other at VIH | 6 | |
| Standby supply current | ISB | 100 | 500 | µA | PU = PD = VIH | 6 | |
| PU, PD, ASE input leakage current | ILI | 10 | µA | VIN = VSS to VCC | 6 | ||
| PU, PD, ASE input HIGH voltage | VIH | 2 | V | 6 | |||
| PU, PD, ASE input LOW voltage | VIL | 0.8 | V | 6 | |||
| Wiper resistance | RW | 40 | 100 | Ω | Wiper current VCC/RTOT | 6 | |
| VH terminal voltage | VVH | -5 | 5 | V | 6 | ||
| VL terminal voltage | VVL | -5 | 5 | V | 6 | ||
| Time between two separate push button events | tGAP | 50 | µs | 6 | |||
| Debounce time | tDB | 30 | 40 | ms | 6 | ||
| Wiper change on slow mode after debounce | tS SLOW | 100 | 250 | 375 | ms | After debounce | 6 |
| Wiper change on fast mode | tS FAST | 25 | 50 | 90 | ms | 6 | |
| Power-up to wiper stable | tPU | 500 | µs | 6 | |||
| AUTOSTORE cycle time | tASTO | 2 | ms | 6 | |||
| AUTOSTORE threshold voltage | VASTH | 4 | V | 6 | |||
| AUTOSTORE cycle end voltage | VASEND | 3.5 | V | 6 | |||
| End-to-end temperature coefficient (X9511W) | 300 | ppm/°C | -40C to +85C, typical | 5 | |||
| Ratiometric temperature coefficient | 20 | ppm | 5 | ||||
| End-to-end resistance (RTOTAL, X9511W) | RTOTAL | 10 | k | 1 | |||
| Supply voltage VCC (nominal) | VCC | 5 | V | 6 |
CAD (KiCad official)
- Symbol:
X9511WSIZT1 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
x9511wsizt1-etched.step/x9511wsizt1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);x9511wsizt1.step/x9511wsizt1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Intersil(Renesas Electronics) datasheet (9 pp, sha256
1c197dfbdde9eaa3, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).