3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMX25U25645GMI00
MXIC(Macronix) · Pre-ordered Products · SOIC-16-300mil
MX25U25645GMI00 from MXIC(Macronix), in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC/SIO3 | bidirectional | No connection, or serial data input and output (SIO3) in 4xI/O read mode when Quad is enabled (depends on part number options). |
| 2 | VCC | power_in | Power supply. |
| 3 | RESET# | input | Hardware reset pin, active low; has an internal pull-up when not physically connected. |
| 4 | NC | unconnected | No connection. |
| 5 | DNU | unconnected | Do not use; it may connect to an internal signal inside the device. |
| 6 | DNU | unconnected | Do not use; it may connect to an internal signal inside the device. |
| 7 | CS# | input | Chip select; enables serial access to the device, and the device is in standby when CS# is high and not in operation. |
| 8 | SO/SIO1 | bidirectional | Serial data output in 1xI/O mode, or serial data input and output in 2xI/O or 4xI/O read mode. |
| 9 | WP#/SIO2 | bidirectional | Write protection, active low, or serial data input and output (SIO2) in 4xI/O read mode; has an internal pull-up when not physically connected. |
| 10 | GND | power_in | Ground. |
| 11 | DNU | unconnected | Do not use; it may connect to an internal signal inside the device. |
| 12 | DNU | unconnected | Do not use; it may connect to an internal signal inside the device. |
| 13 | NC | unconnected | No connection. |
| 14 | NC | unconnected | No connection. |
| 15 | SI/SIO0 | bidirectional | Serial data input in 1xI/O mode, or serial data input and output in 2xI/O or 4xI/O read mode. |
| 16 | SCLK | input | Clock input. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MXIC(Macronix) |
| Package | SOIC-16-300mil |
| Category | Electronic Tools/Instruments/Consumables |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Power Supply | VCC | 1.65 | 2 | V | read, erase, program | 120 | |
| Input Load Current | ILI | -2 | 2 | uA | VCC = VCC Max, VIN = VCC or GND | 115 | |
| Output Leakage Current | ILO | -2 | 2 | uA | VCC = VCC Max, VOUT = VCC or GND | 115 | |
| VCC Standby Current | ISB1 | 20 | 180 | uA | VIN = VCC or GND, CS# = VCC | 115 | |
| Deep Power-down Current | ISB2 | 50 | uA | VIN = VCC or GND, CS# = VCC | 115 | ||
| VCC Read Current | ICC1 | 25 | 35 | mA | f=100MHz (DTR 4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open | 115 | |
| VCC Read Current | ICC1 | 22 | 30 | mA | f=133MHz (4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open | 115 | |
| VCC Read Current | ICC1 | 18 | 25 | mA | f=104MHz (4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open | 115 | |
| VCC Read Current | ICC1 | 13 | 16 | mA | f=84MHz, SCLK=0.1VCC/0.9VCC, SO=Open | 115 | |
| VCC Program Current (PP) | ICC2 | 30 | 40 | mA | Program in Progress, CS# = VCC | 115 | |
| VCC Write Status Register Current | ICC3 | 20 | 40 | mA | Program status register in progress, CS#=VCC | 115 | |
| VCC Sector/Block Erase Current | ICC4 | 30 | 40 | mA | Erase in Progress, CS#=VCC | 115 | |
| VCC Chip Erase Current | ICC5 | 20 | 40 | mA | Erase in Progress, CS#=VCC | 115 | |
| Input Low Voltage (min; max is 0.3VCC) | VIL | -0.4 | V | max printed as 0.3VCC | 115 | ||
| Output Low Voltage | VOL | 0.2 | V | IOL = 100uA | 115 | ||
| Ambient Operating Temperature | -40 | 85 | °C | Industrial grade | 113 | ||
| Storage Temperature | -65 | 150 | °C | 113 | |||
| VCC to Ground Potential | -0.5 | 2.5 | V | 113 | |||
| Applied Input Voltage (min; max is VCC+0.5V) | -0.5 | V | max printed as VCC+0.5V | 113 | |||
| Applied Output Voltage (min; max is VCC+0.5V) | -0.5 | V | max printed as VCC+0.5V | 113 | |||
| Input Capacitance | CIN | 8 | pF | VIN = 0V, TA = 25°C, f = 1.0 MHz | 113 | ||
| Output Capacitance | COUT | 8 | pF | VOUT = 0V, TA = 25°C, f = 1.0 MHz | 113 | ||
| Clock Frequency for all commands (except Read) | fSCLK | 0 | 166 | MHz | min printed as D.C. | 116 | |
| Clock Frequency for READ instructions | fRSCLK | 66 | MHz | 116 | |||
| Clock High Time Normal Read | tCH | 7 | ns | Normal Read (fRSCLK) | 116 | ||
| Clock Low Time Normal Read | tCL | 7 | ns | Normal Read (fRSCLK) | 116 | ||
| Clock Rise Time (peak to peak) | tCLCH | 0.1 | V/ns | 116 | |||
| Clock Fall Time (peak to peak) | tCHCL | 0.1 | V/ns | 116 | |||
| CS# Active Setup Time | tSLCH | 3 | ns | relative to SCLK | 116 | ||
| CS# Not Active Hold Time | tCHSL | 4 | ns | relative to SCLK | 116 | ||
| Data In Setup Time STR | tDVCH | 2 | ns | STR | 116 | ||
| Data In Setup Time DTR | tDVCL | 2 | ns | DTR | 116 | ||
| Data In Hold Time STR | tCHDX | 2 | ns | STR | 116 | ||
| Data In Hold Time DTR | tCLDX | 2 | ns | DTR | 116 | ||
| CS# Active Hold Time | tCHSH | 3 | ns | relative to SCLK | 116 | ||
| CS# Not Active Setup Time | tSHCH | 3 | ns | relative to SCLK | 116 | ||
| CS# Deselect Time Read to Read | tSHSL | 7 | ns | From Read to next Read | 116 | ||
| CS# Deselect Time Write/Erase/Program to Read Status | tSHSL | 30 | ns | From Write/Erase/Program to Read Status Register | 116 | ||
| Output Disable Time | tSHQZ | 8 | ns | 116 | |||
| Clock Low to Output Valid | tCLQV | 5 | ns | 16-SOP, Loading: 30pF | 116 | ||
| Clock Low to Output Valid | tCLQV | 4.5 | ns | 16-SOP, Loading: 15pF | 116 | ||
| Clock Low to Output Valid | tCLQV | 4 | ns | 16-SOP, Loading: 10pF | 116 | ||
| Output Hold Time | tCLQX | 1 | ns | 116 | |||
| Write Protect Setup Time | tWHSL | 20 | ns | 116 | |||
| Write Protect Hold Time | tSHWL | 100 | ns | 116 | |||
| CS# High to Deep Power-down Mode | tDP | 10 | us | 116 | |||
| CS# High to Standby Mode without Electronic Signature Read | tRES1 | 30 | us | 116 | |||
| CS# High to Standby Mode with Electronic Signature Read | tRES2 | 30 | us | 116 | |||
| Write Status/Configuration Register Cycle Time | tW | 40 | ms | 116 | |||
| Write Extended Address Register | tWREAW | 40 | ns | 116 | |||
| Byte-Program Time | tBP | 25 | 60 | us | 116 | ||
| Page Program Cycle Time | tPP | 0.15 | 0.75 | ms | 116 | ||
| Sector Erase Cycle Time | tSE | 25 | 400 | ms | 116 | ||
| Block Erase (32KB) Cycle Time | tBE32 | 150 | 1000 | ms | 116 | ||
| Block Erase (64KB) Cycle Time | tBE | 220 | 1300 | ms | 116 | ||
| Chip Erase Cycle Time | tCE | 75 | 150 | s | 116 | ||
| Erase Suspend Latency | tESL | 25 | us | 117 | |||
| Program Suspend Latency | tPSL | 25 | us | 117 | |||
| Latency between Program Resume and next Suspend | tPRS | 0.3 | 100 | us | 117 | ||
| Latency between Erase Resume and next Suspend | tERS | 0.3 | 400 | us | 117 | ||
| VCC Rise Time | tVR | 500000 | us/V | 118 | |||
| VCC voltage needed to be below VPWD for initialization | VPWD | 0.8 | V | 120 | |||
| Voltage for re-initialization if VDD drops below | V_keep | 1.5 | V | 120 | |||
| Minimum duration for ensuring initialization | tPWD | 300 | us | 120 | |||
| VCC(min.) to device operation | tVSL | 1500 | us | 120 | |||
| Write Inhibit Voltage | VWI | 1 | 1.5 | V | 120 |
CAD (KiCad official)
- Symbol:
MX25U25645GMI00 - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
mx25u25645gmi00-etched.step/mx25u25645gmi00-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mx25u25645gmi00.step/mx25u25645gmi00.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MXIC(Macronix) datasheet (130 pp, sha256
87d9b4345e891239, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).