3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXL9555D
XINLUDA · I/O Expanders · SOP-24-300mil
XL9555D from XINLUDA, in a SOP-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | INT | output | Open-drain active-LOW interrupt output that must be connected to VCC through a pull-up resistor. |
| 2 | A1 | input | Address input 1 that must be connected directly to VCC or ground and must not change while the device is powered. |
| 3 | A2 | input | Address input 2 that must be connected directly to VCC or ground and must not change while the device is powered. |
| 4 | P00 | bidirectional | Port 0 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 5 | P01 | bidirectional | Port 0 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 6 | P02 | bidirectional | Port 0 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 7 | P03 | bidirectional | Port 0 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 8 | P04 | bidirectional | Port 0 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 9 | P05 | bidirectional | Port 0 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 10 | P06 | bidirectional | Port 0 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 11 | P07 | bidirectional | Port 0 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 12 | GND | power_in | Supply ground that must be connected to system ground for proper device operation. |
| 13 | P10 | bidirectional | Port 1 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 14 | P11 | bidirectional | Port 1 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 15 | P12 | bidirectional | Port 1 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 16 | P13 | bidirectional | Port 1 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 17 | P14 | bidirectional | Port 1 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 18 | P15 | bidirectional | Port 1 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 19 | P16 | bidirectional | Port 1 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 20 | P17 | bidirectional | Port 1 push-pull (totem-pole) I/O that powers up as an input; each I/O is limited to 25 mA maximum and the input may be raised to 5.5 V. |
| 21 | A0 | input | Address input 0 that must be connected directly to VCC or ground and must not change while the device is powered. |
| 22 | SCL | input | I2C-bus serial clock line that must be connected to VCC through a pull-up resistor; supports up to 400 kHz fast-mode. |
| 23 | SDA | bidirectional | I2C-bus serial data line that must be connected to VCC through a pull-up resistor. |
| 24 | VCC | power_in | Supply voltage with a recommended operating range of 2.3 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | SOP-24-300mil |
| Category | Interface |
| Pins | 24 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage range | VCC | -0.5 | 6 | V | 4 | ||
| Input pin voltage range | VIN | -0.5 | 6 | V | 4 | ||
| Output pin voltage range | VO | -0.5 | 6 | V | 4 | ||
| Input clamp current | IIK | -20 | mA | VIN<0 | 4 | ||
| Output clamp current | IOK | -20 | mA | VO<0 | 4 | ||
| Input/output clamp current | IIOK | -20 | 20 | mA | VO<0 or VO>VCC | 4 | |
| Continuous output low current | IOL | 50 | mA | VO = 0 to VCC | 4 | ||
| Continuous output high current | IOH | -50 | mA | VO = 0 to VCC | 4 | ||
| Continuous current through GND | ICC | -250 | mA | 4 | |||
| Continuous current through VCC | 160 | mA | 4 | ||||
| Total power dissipation | Ptot | 200 | mW | 4 | |||
| Storage temperature range | Tstg | -65 | 150 | ℃ | 4 | ||
| Ambient temperature range | Tamb | -40 | 85 | ℃ | Operating | 4 | |
| Supply voltage | VCC | 2.3 | 5.5 | V | VCC(MAX) = 5.5V | 5 | |
| Low-level input voltage, SCL/SDA (min; max 0.3×VCC not numeric) | VIL | -0.5 | V | SCL, SDA | 5 | ||
| Low-level input voltage, A2-A0/P07-P00/P17-P10 (min; max 0.3×VCC not numeric) | VIL | -0.5 | V | A2-A0, P07-P00, P17-P10 | 5 | ||
| High-level output current | IOH | -10 | mA | P07-P00, P17-P10 | 5 | ||
| Low-level output current | IOL | 25 | mA | P07-P00, P17-P10 | 5 | ||
| Operating free-air temperature | TA | -40 | 85 | ℃ | 5 | ||
| Supply current, operating mode (XL9555) | ICC | 135 | 200 | μA | I/O = inputs, fSCL = 100 kHz, IO = 0, No load; VCC 5.5 V | 5 | |
| Standby current, standby mode, VIN=GND (XL9555) | ISTB | 1.1 | 1.5 | mA | VIN = GND, I/O = inputs, fSCL = 0 kHz, IO = 0, No load; VCC 5.5 V | 6 | |
| Standby current, standby mode, VIN=VCC (XL9555) | ISTB | 0.25 | 1 | μA | VIN = VCC, I/O = inputs, fSCL = 0 kHz, IO = 0, No load; VCC 5.5 V | 6 | |
| Additional current in standby mode (XL9555) | ΔICC | 1.5 | mA | One input at VCC - 0.6 V, Other inputs at VCC or GND; VCC 2.3 V to 5.5 V | 6 | ||
| Power-on reset voltage, VCC rising | VPORR | 1.7 | 2.2 | V | VIN = VCC or GND, IO = 0, no load | 6 | |
| Power-on reset voltage, VCC falling | VPORF | 0.7 | 1 | V | VIN = VCC or GND, IO = 0, no load | 6 | |
| LOW-level input voltage, SCL/SDA (min; max 0.3×VCC not numeric) | VIL | -0.5 | V | 2.3 V to 5.5 V | 6 | ||
| HIGH-level input voltage, SCL/SDA (max) | VIH | 5.5 | V | 2.3 V to 5.5 V | 6 | ||
| LOW-level output current, SCL/SDA | IOL | 3 | mA | VOL = 0.4 V; 2.3 V to 5.5 V | 6 | ||
| Leakage current, SCL/SDA | IL | -1 | 1 | μA | VIN = VCC or GND; 2.3 V to 5.5 V | 6 | |
| Input capacitance, SCL/SDA | CI | 6 | 10 | pF | VIN = GND; 2.3 V to 5.5 V | 6 | |
| LOW-level input voltage, I/Os (min; max 0.3×VCC not numeric) | VIL | -0.5 | V | 2.3 V to 5.5 V | 6 | ||
| HIGH-level input voltage, I/Os (max) | VIH | 5.5 | V | 2.3 V to 5.5 V | 6 | ||
| LOW-level output current, I/Os (XL9555) | IOL | 8 | mA | VOL = 0.5 V; 2.3 V to 5.5 V | 6 | ||
| LOW-level output current, I/Os (XL9555) | IOL | 10 | mA | VOL = 0.7 V; 2.3 V to 5.5 V | 6 | ||
| HIGH-level output voltage | VOH | 1.8 | V | IOH = -8 mA, VCC = 2.3 V | 6 | ||
| HIGH-level output voltage | VOH | 2.6 | V | IOH = -8 mA, VCC = 3 V | 6 | ||
| HIGH-level output voltage | VOH | 4.1 | V | IOH = -8 mA, VCC = 4.75 V | 6 | ||
| HIGH-level output voltage | VOH | 1.7 | V | IOH = -10 mA, VCC = 2.3 V | 6 | ||
| HIGH-level output voltage | VOH | 2.5 | V | IOH = -10 mA, VCC = 3 V | 6 | ||
| HIGH-level output voltage | VOH | 4 | V | IOH = -10 mA, VCC = 4.75 V | 6 | ||
| HIGH-level input leakage current | ILIH | 1 | μA | VIN = VCC; 5.5 V | 6 | ||
| LOW-level input leakage current (XL9555) | ILIL | -100 | μA | VIN = GND; 5.5 V | 6 | ||
| Input capacitance, I/Os | CI | 3.7 | 5 | pF | VCC 2.3 V to 5.5 V | 6 | |
| Output capacitance, I/Os | CO | 3.7 | 5 | pF | VCC 2.3 V to 5.5 V | 6 | |
| Interrupt LOW-level output current | IOL | 3 | mA | VOL = 0.4 V; 2.3 V to 5.5 V | 6 | ||
| Output capacitance, INT | CO | 3.7 | 5 | pF | VCC 2.3 V to 5.5 V | 6 | |
| LOW-level input voltage, A2-A0 (min; max 0.3×VCC not numeric) | VIL | -0.5 | V | 2.3 V to 5.5 V | 7 | ||
| HIGH-level input voltage, A2-A0 (max) | VIH | 5.5 | V | 2.3 V to 5.5 V | 7 | ||
| Leakage current, A2-A0 | IL | -1 | 1 | μA | VIN = VCC or GND; 2.3 V to 5.5 V | 7 | |
| Input capacitance, A2-A0 | CI | 2.5 | 5 | pF | 2.3 V to 5.5 V | 7 | |
| SCL clock frequency, standard mode | fSCL | 0 | 100 | kHz | Standard-mode | 7 | |
| SCL clock frequency, fast mode | fSCL | 0 | 400 | kHz | Fast-mode | 7 | |
| Data set-up time, standard mode | tSU:DAT | 250 | ns | Standard-mode | 7 | ||
| Data set-up time, fast mode | tSU:DAT | 100 | ns | Fast-mode | 7 | ||
| Data valid time, standard mode | tVD:DAT | 300 | ns | Standard-mode; minimum time for SDA data out valid following SCL LOW | 7 | ||
| Data valid time, fast mode | tVD:DAT | 50 | ns | Fast-mode; minimum time for SDA data out valid following SCL LOW | 7 | ||
| Interrupt valid time, standard mode | tiv(INT_N) | 4 | μs | Standard-mode | 7 | ||
| Interrupt valid time, fast mode | tiv(INT_N) | 4 | μs | Fast-mode | 7 | ||
| Thermal resistance, junction-to-ambient, SOP24 | RθJA | 108.8 | ℃/W | Measured with minimum pad spacing on FR4 PCB, 10 mm by 1 inch, 2 oz copper trace, no air flow | 5 |
CAD (KiCad official)
- Symbol:
XL9555D - Footprint:
Package_SO:SOP-24_7.5x15.4mm_P1.27mm - 3D model: SOP-24-300mil, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 2.65 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
xl9555d-etched.step/xl9555d-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xl9555d.step/xl9555d.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XINLUDA datasheet (25 pp, sha256
8d6805fbf1e452d6, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).