3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownISL22316WFU10Z
RENESAS · Digital Potentiometers · MSOP-10
ISL22316WFU10Z from RENESAS, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | Open-drain I2C serial clock input that requires an external pull-up resistor; input high is 0.7VCC min and low is 0.3VCC max, with fSCL up to 400kHz. |
| 2 | SDA | bidirectional | Open-drain bidirectional I2C serial data I/O that requires an external pull-up resistor, with VOL of 0.4V max when sinking 4mA. |
| 3 | A1 | input | Device address input that sets bit 1 of the 7-bit I2C slave address, allowing up to four devices per bus. |
| 4 | A0 | input | Device address input that sets the least significant bit of the I2C slave address, allowing up to four devices per bus. |
| 5 | SHDN | input | Active-low shutdown input that opens RH and shorts RW to RL when pulled low, is ANDed with the ACR SHDN bit, and must remain HIGH for normal operation. |
| 6 | GND | power_in | Device ground pin. |
| 7 | RL | passive | Low terminal of the DCP, with voltage range 0 to VCC and the wiper closest to it at WR=0. |
| 8 | RW | passive | Wiper terminal of the DCP, positioned by the 7-bit Wiper Register, with typical wiper resistance of 70 ohms at VCC=3.3V (200 ohms max). |
| 9 | RH | passive | High terminal of the DCP, with voltage range 0 to VCC and the wiper closest to it at WR=127. |
| 10 | VCC | power_in | Power supply pin, operating range 2.7V to 5.5V (absolute maximum 6V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | MSOP-10 |
| Category | Data Converters |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| RH to RL Resistance Tolerance | -20 | 20 | % | 3 | |||
| RH to RL Resistance (W option) | RTOTAL | 10 | kΩ | W option | 3 | ||
| End-to-End Temperature Coefficient | -50 | 50 | ppm/°C | W option (Note 18) | 3 | ||
| Wiper Resistance | RW | 70 | 200 | Ω | VCC = 3.3V, wiper current = VCC/RTOTAL | 3 | |
| VRH and VRL Terminal Voltages | VRH, VRL | 0 | 5.5 | V | VRH and VRL to GND; printed max VCC | 3 | |
| Leakage on DCP Pins | ILkgDCP | 0.1 | 1 | µA | Voltage at pin from GND to VCC | 3 | |
| Integral Non-linearity (voltage divider) | INL | -1 | 1 | LSB | Monotonic over all tap positions, W and U option | 3 | |
| Differential Non-linearity (voltage divider) | DNL | -0.5 | 0.5 | LSB | Monotonic over all tap positions, W and U option | 3 | |
| Zero-scale Error | ZSerror | 0 | 1 | 5 | LSB | W option | 3 |
| Full-scale Error | FSerror | -5 | -1 | 0 | LSB | W option | 3 |
| Ratiometric Temperature Coefficient | TCV | 4 | ppm/°C | DCP register set to 40 hex for W and U option (Notes 11, 18); printed ±4 | 3 | ||
| Integral Non-linearity (resistor mode) | RINL | -1 | 1 | MI | DCP register set between 10 hex and 7F hex; monotonic; W and U option | 4 | |
| Differential Non-linearity (resistor mode) | RDNL | -1 | 1 | MI | W option | 4 | |
| Offset (resistor mode) | Roffset | 0 | 1 | 5 | MI | W option | 4 |
| VCC Supply Current (Volatile Write/Read) | ICC1 | 0.5 | mA | fSCL = 400kHz; SDA = Open | 4 | ||
| VCC Supply Current (Non-volatile Write/Read) | ICC2 | 3 | mA | fSCL = 400kHz; SDA = Open | 4 | ||
| VCC Current (Standby) | ISB | 5 | µA | VCC = +5.5V @ +85°C, I2C interface in standby state | 4 | ||
| VCC Current (Standby) | ISB | 7 | µA | VCC = +5.5V @ +125°C, I2C interface in standby state | 4 | ||
| VCC Current (Standby) | ISB | 3 | µA | VCC = +3.6V @ +85°C, I2C interface in standby state | 4 | ||
| VCC Current (Shutdown) | ISD | 3 | µA | VCC = +5.5V @ +85°C, I2C interface in standby state | 4 | ||
| VCC Current (Shutdown) | ISD | 5 | µA | VCC = +5.5V @ +125°C, I2C interface in standby state | 4 | ||
| VCC Current (Shutdown) | ISD | 2 | µA | VCC = +3.6V @ +85°C, I2C interface in standby state | 4 | ||
| VCC Current (Shutdown) | ISD | 4 | µA | VCC = +3.6V @ +125°C, I2C interface in standby state | 4 | ||
| Leakage Current at Digital Pins | ILkgDig | -1 | 1 | µA | Voltage at pin from GND to VCC, SDA is inactive | 4 | |
| Power-on Recall Voltage | Vpor | 2 | 2.6 | V | Minimum VCC at which memory recall occurs | 4 | |
| VCC Ramp Rate | VCCRamp | 0.2 | V/ms | 4 | |||
| Power-up Delay | tD | 3 | ms | VCC above Vpor, to DCP IVR recall completed and I2C interface in standby state | 4 | ||
| Non-volatile Write Cycle Time | tWC | 12 | 20 | ms | 5 | ||
| Input Buffer LOW Voltage | VIL | -0.3 | 0.3 | V | A1, A0, SHDN, SDA, SCL; max printed 0.3*VCC | 5 | |
| Input Buffer HIGH Voltage | VIH | 0.7 | 0.3 | V | A1, A0, SHDN, SDA, SCL; min printed 0.7*VCC, max VCC + 0.3 | 5 | |
| SDA Output Buffer LOW Voltage | VOL | 0 | 0.4 | V | Sinking 4mA | 5 | |
| SCL Frequency | fSCL | 400 | kHz | 5 | |||
| Pulse Width Suppression Time | tsp | 50 | ns | Any pulse narrower than the max spec is suppressed | 5 | ||
| SCL Falling Edge to SDA Output Data Valid | tAA | 900 | ns | SCL falling edge crossing 30% of VCC, until SDA exits the 30% to 70% of VCC window | 5 | ||
| Bus Free Time | tBUF | 1300 | ns | SDA crossing 70% of VCC during STOP, to SDA crossing 70% of VCC during following START | 5 | ||
| Clock LOW Time | tLOW | 1300 | ns | Measured at the 30% of VCC crossing | 5 | ||
| Clock HIGH Time | tHIGH | 600 | ns | Measured at the 70% of VCC crossing | 5 | ||
| START Condition Setup Time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge; both crossing 70% of VCC | 5 | ||
| START Condition Hold Time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC | 5 | ||
| Input Data Setup Time | tSU:DAT | 100 | ns | From SDA exiting the 30% to 70% of VCC window, to SCL rising edge crossing 30% of VCC | 5 | ||
| Input Data Hold Time | tHD:DAT | 0 | ns | From SCL rising edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window | 5 | ||
| STOP Condition Setup Time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VCC, to SDA rising edge crossing 30% of VCC | 5 | ||
| STOP Condition Hold Time | tHD:STO | 1300 | ns | From SDA rising edge to SCL falling edge; both crossing 70% of VCC | 5 | ||
| Output Data Hold Time | tDH | 0 | ns | From SCL falling edge crossing 30% of VCC, until SDA enters the 30% to 70% of VCC window | 5 | ||
| SDA and SCL Rise Time | tR | 250 | ns | From 30% to 70% of VCC; min 20 + 0.1*Cb | 5 | ||
| SDA and SCL Fall Time | tF | 250 | ns | From 70% to 30% of VCC; min 20 + 0.1*Cb | 5 | ||
| Capacitive Loading of SDA or SCL | Cb | 10 | 400 | pF | Total on-chip and off-chip | 5 | |
| SDA and SCL Bus Pull-up Resistor | Rpu | 1 | kΩ | Off-chip | 6 | ||
| A1 and A0 Setup Time | tSU:A | 600 | ns | Before START condition | 6 | ||
| A1 and A0 Hold Time | tHD:A | 600 | ns | After STOP condition | 6 | ||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Voltage at any Digital Interface Pin | -0.3 | 0.3 | V | With respect to GND; max printed VCC+0.3 | 3 | ||
| VCC | VCC | -0.3 | 6 | V | 3 | ||
| Voltage at any DCP Pin | -0.3 | V | With respect to GND; max printed VCC | 3 | |||
| Wiper Current IW (10s) | IW | -6 | 6 | mA | 10s | 3 | |
| Maximum Junction Temperature | 150 | °C | Plastic package | 3 | |||
| ESD Human Body Model | 5 | kV | 3 | ||||
| ESD Charge Device Model | 1 | kV | 3 | ||||
| Temperature Range (Extended Industrial) | -40 | 125 | °C | 3 | |||
| Supply Voltage | VCC | 2.7 | 5.5 | V | 3 | ||
| Power Rating of each DCP | 5 | mW | 3 | ||||
| Wiper Current of each DCP | -3 | 3 | mA | 3 | |||
| Thermal Resistance Junction to Ambient, 10 Lead MSOP | θJA | 162 | °C/W | Note 2 | 3 |
CAD (KiCad official)
- Symbol:
ISL22316WFU10Z - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
isl22316wfu10z-etched.step/isl22316wfu10z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl22316wfu10z.step/isl22316wfu10z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (16 pp, sha256
db2bf3d39b37b76a, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).