main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers isl22316wfu10z: viewers · Ray
isl22316wfu10z-etched.glb Publish 0.1.0 · Ray
isl22316wfu10z-etched.step isl22316wfu10z: factory component page (tier=mfr) · Ray
isl22316wfu10z-hero.glb isl22316wfu10z: hero GLB from the etched model (keeps the MPN mark) · Ray
isl22316wfu10z-hero.overlay.json Publish 0.1.0 · Ray
isl22316wfu10z.glb Publish 0.1.0 · Ray
isl22316wfu10z.kicad_mod Publish 0.1.0 · Ray
isl22316wfu10z.kicad_sym Publish 0.1.0 · Ray
isl22316wfu10z.lbr Publish 0.1.0 · Ray
isl22316wfu10z.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 10 pins · Ray

ISL22316WFU10Z

RENESAS · Digital Potentiometers · MSOP-10

ISL22316WFU10Z from RENESAS, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SCL input Open-drain I2C serial clock input that requires an external pull-up resistor; input high is 0.7VCC min and low is 0.3VCC max, with fSCL up to 400kHz.
2 SDA bidirectional Open-drain bidirectional I2C serial data I/O that requires an external pull-up resistor, with VOL of 0.4V max when sinking 4mA.
3 A1 input Device address input that sets bit 1 of the 7-bit I2C slave address, allowing up to four devices per bus.
4 A0 input Device address input that sets the least significant bit of the I2C slave address, allowing up to four devices per bus.
5 SHDN input Active-low shutdown input that opens RH and shorts RW to RL when pulled low, is ANDed with the ACR SHDN bit, and must remain HIGH for normal operation.
6 GND power_in Device ground pin.
7 RL passive Low terminal of the DCP, with voltage range 0 to VCC and the wiper closest to it at WR=0.
8 RW passive Wiper terminal of the DCP, positioned by the 7-bit Wiper Register, with typical wiper resistance of 70 ohms at VCC=3.3V (200 ohms max).
9 RH passive High terminal of the DCP, with voltage range 0 to VCC and the wiper closest to it at WR=127.
10 VCC power_in Power supply pin, operating range 2.7V to 5.5V (absolute maximum 6V).

Key specifications

Parameter Value
Manufacturer RENESAS
Package MSOP-10
Category Data Converters
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
RH to RL Resistance Tolerance -20 20 % 3
RH to RL Resistance (W option) RTOTAL 10 kΩ W option 3
End-to-End Temperature Coefficient -50 50 ppm/°C W option (Note 18) 3
Wiper Resistance RW 70 200 Ω VCC = 3.3V, wiper current = VCC/RTOTAL 3
VRH and VRL Terminal Voltages VRH, VRL 0 5.5 V VRH and VRL to GND; printed max VCC 3
Leakage on DCP Pins ILkgDCP 0.1 1 µA Voltage at pin from GND to VCC 3
Integral Non-linearity (voltage divider) INL -1 1 LSB Monotonic over all tap positions, W and U option 3
Differential Non-linearity (voltage divider) DNL -0.5 0.5 LSB Monotonic over all tap positions, W and U option 3
Zero-scale Error ZSerror 0 1 5 LSB W option 3
Full-scale Error FSerror -5 -1 0 LSB W option 3
Ratiometric Temperature Coefficient TCV 4 ppm/°C DCP register set to 40 hex for W and U option (Notes 11, 18); printed ±4 3
Integral Non-linearity (resistor mode) RINL -1 1 MI DCP register set between 10 hex and 7F hex; monotonic; W and U option 4
Differential Non-linearity (resistor mode) RDNL -1 1 MI W option 4
Offset (resistor mode) Roffset 0 1 5 MI W option 4
VCC Supply Current (Volatile Write/Read) ICC1 0.5 mA fSCL = 400kHz; SDA = Open 4
VCC Supply Current (Non-volatile Write/Read) ICC2 3 mA fSCL = 400kHz; SDA = Open 4
VCC Current (Standby) ISB 5 µA VCC = +5.5V @ +85°C, I2C interface in standby state 4
VCC Current (Standby) ISB 7 µA VCC = +5.5V @ +125°C, I2C interface in standby state 4
VCC Current (Standby) ISB 3 µA VCC = +3.6V @ +85°C, I2C interface in standby state 4
VCC Current (Shutdown) ISD 3 µA VCC = +5.5V @ +85°C, I2C interface in standby state 4
VCC Current (Shutdown) ISD 5 µA VCC = +5.5V @ +125°C, I2C interface in standby state 4
VCC Current (Shutdown) ISD 2 µA VCC = +3.6V @ +85°C, I2C interface in standby state 4
VCC Current (Shutdown) ISD 4 µA VCC = +3.6V @ +125°C, I2C interface in standby state 4
Leakage Current at Digital Pins ILkgDig -1 1 µA Voltage at pin from GND to VCC, SDA is inactive 4
Power-on Recall Voltage Vpor 2 2.6 V Minimum VCC at which memory recall occurs 4
VCC Ramp Rate VCCRamp 0.2 V/ms 4
Power-up Delay tD 3 ms VCC above Vpor, to DCP IVR recall completed and I2C interface in standby state 4
Non-volatile Write Cycle Time tWC 12 20 ms 5
Input Buffer LOW Voltage VIL -0.3 0.3 V A1, A0, SHDN, SDA, SCL; max printed 0.3*VCC 5
Input Buffer HIGH Voltage VIH 0.7 0.3 V A1, A0, SHDN, SDA, SCL; min printed 0.7*VCC, max VCC + 0.3 5
SDA Output Buffer LOW Voltage VOL 0 0.4 V Sinking 4mA 5
SCL Frequency fSCL 400 kHz 5
Pulse Width Suppression Time tsp 50 ns Any pulse narrower than the max spec is suppressed 5
SCL Falling Edge to SDA Output Data Valid tAA 900 ns SCL falling edge crossing 30% of VCC, until SDA exits the 30% to 70% of VCC window 5
Bus Free Time tBUF 1300 ns SDA crossing 70% of VCC during STOP, to SDA crossing 70% of VCC during following START 5
Clock LOW Time tLOW 1300 ns Measured at the 30% of VCC crossing 5
Clock HIGH Time tHIGH 600 ns Measured at the 70% of VCC crossing 5
START Condition Setup Time tSU:STA 600 ns SCL rising edge to SDA falling edge; both crossing 70% of VCC 5
START Condition Hold Time tHD:STA 600 ns From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC 5
Input Data Setup Time tSU:DAT 100 ns From SDA exiting the 30% to 70% of VCC window, to SCL rising edge crossing 30% of VCC 5
Input Data Hold Time tHD:DAT 0 ns From SCL rising edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window 5
STOP Condition Setup Time tSU:STO 600 ns From SCL rising edge crossing 70% of VCC, to SDA rising edge crossing 30% of VCC 5
STOP Condition Hold Time tHD:STO 1300 ns From SDA rising edge to SCL falling edge; both crossing 70% of VCC 5
Output Data Hold Time tDH 0 ns From SCL falling edge crossing 30% of VCC, until SDA enters the 30% to 70% of VCC window 5
SDA and SCL Rise Time tR 250 ns From 30% to 70% of VCC; min 20 + 0.1*Cb 5
SDA and SCL Fall Time tF 250 ns From 70% to 30% of VCC; min 20 + 0.1*Cb 5
Capacitive Loading of SDA or SCL Cb 10 400 pF Total on-chip and off-chip 5
SDA and SCL Bus Pull-up Resistor Rpu 1 kΩ Off-chip 6
A1 and A0 Setup Time tSU:A 600 ns Before START condition 6
A1 and A0 Hold Time tHD:A 600 ns After STOP condition 6
Storage Temperature -65 150 °C 3
Voltage at any Digital Interface Pin -0.3 0.3 V With respect to GND; max printed VCC+0.3 3
VCC VCC -0.3 6 V 3
Voltage at any DCP Pin -0.3 V With respect to GND; max printed VCC 3
Wiper Current IW (10s) IW -6 6 mA 10s 3
Maximum Junction Temperature 150 °C Plastic package 3
ESD Human Body Model 5 kV 3
ESD Charge Device Model 1 kV 3
Temperature Range (Extended Industrial) -40 125 °C 3
Supply Voltage VCC 2.7 5.5 V 3
Power Rating of each DCP 5 mW 3
Wiper Current of each DCP -3 3 mA 3
Thermal Resistance Junction to Ambient, 10 Lead MSOP θJA 162 °C/W Note 2 3

CAD (KiCad official)

  • Symbol: ISL22316WFU10Z
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: isl22316wfu10z-etched.step / isl22316wfu10z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl22316wfu10z.step / isl22316wfu10z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (16 pp, sha256 db2bf3d39b37b76a, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF