Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PTD08A015WAD

Texas Instruments · DC-DC Power Modules · DIP-12

PTD08A015WAD from Texas Instruments, in a DIP-12. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VI power_in The positive input voltage power node to the module, referenced to common GND, with an input range of 4.75 V to 14 V.
2 GND power_in This is the common ground connection for the VI and VO power connections.
3 GND power_in This is the common ground connection for the VI and VO power connections.
4 VO power_out The regulated positive power output with respect to GND, adjustable from 0.7 V to 3.6 V.
5 TEMP output Temperature sense output whose voltage level represents the module temperature.
6 IOUT output Current sense output whose voltage level represents the average output current of the module.
7 AGND power_in Analog ground return that is the 0 Vdc reference for the control inputs.
8 INH input Negative-logic inhibit input referenced to AGND; a low level disables the module and turns off the output, and a 10 kΩ pull-up to 3.3 V or 5 V is required if INH is not used.
9 FAULT output Current-limit flag that is a 3.3 V digital output, latched high after an over-current condition and reset after two complete PWM cycles without an over-current condition.
10 SRE input High-impedance digital input accepting 3.3 V or 5 V logic that enables the synchronous rectifier; when high the module sources and sinks output current, and when low it only sources current.
11 PWM input High-impedance digital PWM input that accepts 3.3 V or 5 V logic levels up to 1 MHz.
12 VBIAS power_in Bias voltage supply required to power the internal circuitry, which should be connected to VI for optimal performance (bias range 4.75 V to 14 V).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package DIP-12
Category Power Modules
Pins 12

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output current IO 0 15 A Over VO range; 25°C, natural convection 4
Input voltage range VI 4.75 14 V Over IO range; max duty-cycle limited per footnote (1) 4
Output voltage adjust range VOADJ 0.7 3.6 V Over IO range 4
Bias voltage VB 4.75 14 V 4
Bias voltage under voltage lockout (rising) VB 4.25 4.5 4.75 V VB increasing 4
Bias voltage under voltage lockout (falling) VB 4 4.25 4.5 V VB decreasing 4
High-level input voltage VIH 2 5.5 V SRE, INH, & PWM input levels 4
PWM input frequency range 300 1000 kHz PWM input 4
TEMP output range -40 125 °C TEMP output 4
TEMP output accuracy -4 6 °C -40°C ≤ TA ≤ 85°C 4
FAULT high-level output voltage VOH 2.7 3.3 V IFAULT = 4mA 4
FAULT low-level output voltage VOL 0 0.6 V IFAULT = 4mA 4
IOUT output range 0.15 3.5 V IOUT output 4
IOUT output gain 60 85 110 mV/A IOUT output 4
IOUT output offset 0.44 0.6 0.76 V IO = 0A, VO = 1.2V 4
IOUT output impedance 10 15 21 kΩ 4
External output capacitance, nonceramic (maximum) CO 5000 µF Nonceramic; calculated max for 1 V/ms output rise time (footnote 4) 4
Equivalent series resistance, nonceramic output capacitance (minimum) ESR 1 mΩ Non-ceramic output capacitance; minimum ESR per footnote (5) 4
Input voltage VI 16 V Voltages with respect to GND 3
Bias voltage VB 16 V Voltages with respect to GND 3
Operating temperature range TA -40 85 °C Over VI range 3
Storage temperature Tstg -55 125 °C 3
Wave soldering temperature Twave 260 °C Surface temperature of module body or pins for 5 seconds 3

CAD (KiCad official)

  • Symbol: PTD08A015WAD
  • Footprint: Package_DIP:DIP-12_W7.62mm
  • 3D model: DIP-12 (KiCad packages3D, STEP)
  • 3D model files: ptd08a015wad-etched.step / ptd08a015wad-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ptd08a015wad.step / ptd08a015wad.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (15 pp, sha256 a37198b1e8d850bf, retrieved 2026-10-11, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF