3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownVRB2412LD-15WR3
YLPTEC · Isolated Power Modules · DIP-6
VRB2412LD-15WR3 from YLPTEC, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | -Vin | power_in | Negative input supply terminal for the 24 VDC input family (18-36 VDC operating range, 50 V 1-second surge maximum, undervoltage turn-off 12-16.5 VDC). |
| 2 | +Vin | power_in | Positive input supply terminal; the 24 VDC input version operates from 18-36 VDC with a start-up voltage of 18 VDC maximum. |
| 3 | +Vo | power_out | Positive regulated output, rated 12 VDC at up to 1250 mA maximum for this variant, with output voltage accuracy of ±1% typical and ±3% maximum at 0-100% load. |
| 4 | Trim | input | Output voltage trim pin, adjustable over 90-110 %Vo with the external resistor network shown in the trim circuit of the datasheet. |
| 5 | GND | power_in | Output ground return, the common reference for +Vo and for the CTRL pin. |
| 6 | CTRL | input | Remote on/off control: left floating or driven high at 3.5-12 VDC turns the module on, while connection to GND or a level of 0-1.2 VDC turns it off (4-7 mA input current when off). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | YLPTEC |
| Package | DIP-6 |
| Category | Power Modules |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | Vin | 18 | 24 | 36 | V | 1 | |
| Output current | 0 | 1250 | mA | 1 | |||
| Maximum capacitive load | 1000 | µF | Full load, input voltage range | 1 | |||
| Full load efficiency | 87 | 89 | % | Full load | 1 | ||
| Input current, full load (24 VDC input, other outputs) | 702 | 718 | mA | 24 VDC input, other outputs, full load | 1 | ||
| Input current, no load (24 VDC input, other outputs) | 5 | 10 | mA | 24 VDC input, other outputs, no load | 1 | ||
| Surge voltage (1 s max), 24 VDC input | -0.7 | 50 | VDC | 1 s max, 24 VDC input | 1 | ||
| Start-up voltage, 24 VDC input | 18 | VDC | 24 VDC input | 1 | |||
| Undervoltage shutdown voltage, 24 VDC input | 12 | 16.5 | VDC | 24 VDC input | 1 | ||
| Remote control on voltage (CTRL) | CTRL | 3.5 | 12 | VDC | Module on: CTRL floating or TTL high | 1 | |
| Remote control off voltage (CTRL) | CTRL | 0 | 1.2 | VDC | Module off: CTRL to GND or low level | 2 | |
| Shutdown input current | 4 | 7 | mA | Module shut down | 2 | ||
| Output voltage accuracy | -3 | 1 | 3 | 0%-100% load | 2 | ||
| Line regulation | -0.5 | 0.2 | 0.5 | % | Full load, input voltage low to high | 2 | |
| Load regulation | -1 | 0.5 | 1 | Nominal input voltage | 2 | ||
| Ripple and noise | 50 | 100 | mVp-p | 20 MHz bandwidth, 5%-100% load | 2 | ||
| Transient recovery time | 300 | 500 | μs | 25% load step, nominal input voltage | 2 | ||
| Transient response deviation, other outputs | -5 | 3 | 5 | % | 2 | ||
| Temperature drift coefficient | -0.03 | 0.03 | %/℃ | 2 | |||
| Output voltage trim range | 90 | 110 | %Vo | Input voltage range | 2 | ||
| Overvoltage protection | 110 | 160 | 2 | ||||
| Overcurrent protection | 110 | 190 | %Io | 2 | |||
| Isolation voltage | 1500 | VDC | Input-output, 1 min, leakage current less than 1 mA | 2 | |||
| Insulation resistance | 1000 | MΩ | Input-output, 500 VDC insulation voltage | 2 | |||
| Mean time between failures | 1000 | K Hours | MIL-HDBK-217F @25℃ | 2 | |||
| Operating temperature | -40 | 85 | ℃ | See Figure 1 | 2 | ||
| Storage temperature | -55 | 125 | ℃ | 2 | |||
| Storage humidity | 5 | 95 | %RH | Non-condensing | 2 | ||
| Lead soldering temperature | 300 | ℃ | 1.5 mm from case, 10 s | 2 |
CAD (Adom-generated)
- Symbol:
VRB2412LD-15WR3 - Footprint:
Adom_Gen:YLPTEC_VRB2412_2d2373 - 3D model: generated to fit the land (STEP)
- 3D model files:
vrb2412ld-15wr3-etched.step/vrb2412ld-15wr3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);vrb2412ld-15wr3.step/vrb2412ld-15wr3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: YLPTEC datasheet (5 pp, sha256
0538c58af128bd54, retrieved 2026-11-12, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: YLPTEC prints pin positions and pin diameter but no hole or pad size. Pin dia. 1.00 (lateral view) with the sheet's unmarked pin-diameter tolerance +/-0.10, so 1.10 max; drill 1.3 (max lead + 0.2) and 2.2 round pads (1.3 + 2 x 0.45 annular ring) are mine. Closest pins are 1 and 2 at 5.08, so 2.88 between pad edges.