Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

EL5160IWZ-T7

RENESAS · Pre-ordered Chips · SOT-23-6

EL5160IWZ-T7 from RENESAS, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 OUT output Amplifier output; the device has no internal current limiting, so a shorted output can exceed the absolute maximum output current (50mA maximum continuous) or power dissipation and destroy the device.
2 VS- power_in Negative supply; the part operates over a total supply span of 5V to 10V (for example ±2.5V to ±5V on dual supplies), and the absolute maximum supply voltage between VS+ and VS- is 13.2V.
3 IN+ input Non-inverting input; the input range extends to within 2V of either supply (±3V common-mode range on ±5V supplies).
4 IN- input Inverting input; stray capacitance at this node should be kept to a minimum and a ground plane is not recommended around this pin.
5 CE input Chip enable; the amplifier is disabled when CE is pulled to within 1V of the positive supply and is enabled when CE is floating or pulled at least 3V below the positive supply.
6 VS+ power_in Positive supply; the part operates over a total supply span of 5V to 10V, and the absolute maximum supply voltage between VS+ and VS- is 13.2V.

Key specifications

Parameter Value
Manufacturer RENESAS
Package SOT-23-6
Category Interface ICs
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Slew Rate (EL5160, EL5161 rows) SR 900 1700 2500 V/µs VO = -2.5V to +2.5V, AV = +2, RF = RG = 1kΩ, RL = 100Ω 3
Input Offset Voltage VOS -5 1.6 5 mV 3
Open Loop Transimpedance Gain ROL 800 2000 kΩ ±2.5VOUT into 150Ω 3
Common Mode Input Range CMIR 3 3.3 V Guaranteed by CMRR test 3
Common Mode Rejection Ratio CMRR 50 62 75 dB VIN = ±3V 3
Input Current Common Mode Rejection -ICMR -1 1 µA/V 3
Input Current +IIN -4 4 µA 3
Input Current -IIN -5 5 µA 3
Input Resistance RIN 1.5 4 15 MΩ 3
Output Voltage Swing VO 3.1 3.4 3.8 V RL = 150Ω to GND 4
Output Voltage Swing VO 3.8 4 4.2 V RL = 1kΩ to GND 4
Output Current IOUT 40 70 140 mA RL = 10Ω to GND 4
Supply Current - Enabled, per Amplifier ISON 0.6 0.75 0.85 mA No load, VIN = 0V (EL5160, EL5161, EL5260, EL5261) 4
Supply Current - Disabled, per Amplifier ISOFF+ 0 10 25 µA No load, VIN = 0V, Only EL5160, EL5260, EL5360 4
Supply Current - Disabled, per Amplifier ISOFF- -25 -14 0 µA 4
Power Supply Rejection Ratio PSRR 65 74 dB DC, VS = ±4.75V to ±5.25V 4
Input Current Power Supply Rejection -IPSR -0.5 0.1 0.5 µA/V DC, VS = ±4.75V to ±5.25V 4
CE Pin Input High Current ICE, H 1 5 25 µA CE = VS+ 4
CE Pin Input Low Current ICE, L -1 0 1 µA CE = (VS+) - 5V 4
Supply Voltage between VS+ and VS- 13.2 V 3
Maximum Continuous Output Current 50 mA 3
Slew Rate of VS+ to VS- 1 V/µs 3
Maximum Operating Junction Temperature 125 °C 3
Maximum Storage Temperature Range -65 150 °C 3
Ambient Operating Temperature Range -40 85 °C 3
Supply Voltage Span (single or dual supply) 5 10 V VS+ to VS-, single or dual supply 1
Thermal Resistance, junction-to-ambient, SOT23-5/6 JA 110 °C/W JEDEC JESD51-7 high effective thermal conductivity test board 7
Thermal Resistance, junction-to-ambient, SOT23-5/6 JA 256 °C/W JEDEC JESD51-3 low effective thermal conductivity test board 7

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: EL5160IWZ-T7
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: el5160iwz-t7-etched.step / el5160iwz-t7-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); el5160iwz-t7.step / el5160iwz-t7.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (17 pp, sha256 503f6fa837fc069d, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF