Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MP6543CGL-Z

Monolithic Power Systems · Motor Driver ICs · QFN-24(3x4)

MP6543CGL-Z from Monolithic Power Systems, in a QFN-24(3x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 ENB input Phase B enable input; when low the phase B outputs are Hi-Z and PWMB is ignored, with an internal weak pull-down.
2 ENC input Phase C enable input; when low the phase C outputs are Hi-Z and PWMC is ignored, with an internal weak pull-down.
3 PWMA input Phase A pulse-width modulation (PWM) input that sets SA to VIN when high and GND when low while ENA is high.
4 PWMB input Phase B PWM input that sets SB to VIN when high and GND when low while ENB is high.
5 PWMC input Phase C PWM input that sets SC to VIN when high and GND when low while ENC is high.
6 VIN power_in Input supply voltage, 3V to 22V operating (25V absolute maximum), needing a bypass capacitor on each VIN pin.
7 SA output Phase A half-bridge output.
8 LSSA passive Phase A low-side MOSFET (LS-FET) source connection, which can go to an external shunt resistor (-0.3V to +0.3V relative to GND).
9 SB output Phase B half-bridge output.
10 LSSB passive Phase B LS-FET source connection, which can go to an external shunt resistor (-0.3V to +0.3V relative to GND).
11 SC output Phase C half-bridge output.
12 LSSC passive Phase C LS-FET source connection, which can go to an external shunt resistor (-0.3V to +0.3V relative to GND).
13 VIN power_in Input supply voltage, 3V to 22V operating (25V absolute maximum), needing a bypass capacitor on each VIN pin.
14 VCP power_out Charge pump output; connect VCP to VIN with a 1µF, 16V X7R ceramic capacitor (typically VIN + 3.3V).
15 GND power_in Ground.
16 VIN_LDO power_in LDO input, 3V to 22V.
17 OC_ADJ input Over-current protection (OCP) configurable current limit pin; the OCP threshold is typically 5A with ROCP = 0 and 7A when floating.
18 V3P3 power_out 3.3V regulator output (100mA) and LS-FET gate driver supply voltage; bypass to GND with a 4.7µF capacitor.
19 nFAULT output Open-drain fault indicator that is logic low when a fault occurs and needs an external pull-up resistor.
20 SOC output Phase C current-sense output that sources or sinks a current of 1/4000 of the phase C LS-FET current.
21 SOB output Phase B current-sense output that sources or sinks a current of 1/4000 of the phase B LS-FET current.
22 SOA output Phase A current-sense output that sources or sinks a current of 1/4000 of the phase A LS-FET current.
23 nSLEEP input Sleep mode input; pull low to enter low-power sleep mode and high to exit, with an internal pull-down resistor.
24 ENA input Phase A enable input; when low the phase A outputs are Hi-Z and PWMA is ignored, with an internal weak pull-down.
25 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package QFN-24(3x4)
Category Power Management
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN 3 22 V 5
LDO input voltage VIN_LDO 3 22 V 5
Quiescent current IQ 2.5 3.2 mA nSLEEP = 1, ENx = 0 5
Sleep current ISLEEP 45 60 µA nSLEEP = 0 5
Input logic low threshold VIN_LOW 0.4 V 5
Input logic high threshold VIN_HIGH 1.5 V 5
Logic input current high IIN_HIGH -20 20 µA V = 3.3V 5
Logic input current low IIN_LOW -20 20 µA V = 0V 5
LDO output V3P3 3.2 3.32 3.45 V IOUT = 0mA to 80mA 5
UVLO threshold VUVLO 2.5 2.7 2.9 V VIN rising 5
OCP threshold IOCP 4 5 6.5 A ROCP = 0 5
OCP threshold IOCP 4.8 7 8.8 A ROCP is floating 5
CS output current 225 250 275 µA ILS-FET = 1A 5
CS output current -275 -250 -225 µA ILS-FET = -1A 5
CS output current 22.5 25 27.5 µA ILS-FET = 100mA 5
CS output current -27.5 -25 -22.5 µA ILS-FET = -100mA 5
Positive-to-negative ratio 95 105 % ILS-FET = ±1A, ±100mA 5
Phase-to-phase ratio 95 105 % ILS-FET = ±1A, ±100mA 5
CS output voltage swing 0 3.6 V ILS-FET = ±0.25A 5
HS-FET on resistance RDS(ON)_HS 90 115 135 mΩ IOUT = 1A 5
LS-FET on resistance RDS(ON)_LS 85 110 125 mΩ IOUT = 1A 5
Start-up delay tDELAY_SU 1.5 ms VIN is rising or VnSLEEP is rising 5
Internal pull-down resistance RPD 500 kΩ All logic inputs 5
nFAULT pull-down resistance RDS(ON)_nFAULT 15 Ω 5
UVLO hysteresis ∆VUVLO 150 mV 5
OCP deglitch time tOCP 1 µs 5
Thermal shutdown TTSD 160 °C TJ rising; not tested in production 5
Thermal shutdown hysteresis ∆TTSD 25 °C Not tested in production 5
Output rise time 25 ns RLOAD = 50Ω; not tested in production 5
Output fall time 25 ns RLOAD = 50Ω; not tested in production 5
Dead time 40 ns RLOAD = 50Ω; not tested in production 5
PWMx to Sx delay time rising 70 ns Not tested in production 6
PWMx to Sx delay time falling 70 ns Not tested in production 6
Supply voltage (VIN, VIN_LDO) -0.3 25 V 4
LSSx to GND -0.3 0.3 V 4
All other pins -0.3 5 V 4
Continuous power dissipation 2.6 W TA = 25°C, QFN-24 (3mmx4mm) 4
Junction temperature TJ 150 °C 4
Storage temperature -65 150 °C 4
ESD HBM -2 2 kV Human body model 4
ESD CDM -2 2 kV Charged device model 4
Supply voltage VIN 3 22 V 4
Output current IOUT 1.2 A Continuous current depends on PCB layout and ambient temperature 4
Operating junction temperature TJ -40 125 °C 4
Thermal resistance junction-to-case θJC 10 °C/W QFN-24 (3mmx4mm), JESD51-7 4-layer PCB 4

CAD (KiCad official)

  • Symbol: MP6543CGL-Z
  • Footprint: Package_DFN_QFN:QFN-24-1EP_3x4mm_P0.4mm_EP1.65x2.65mm
  • 3D model: QFN-24(3x4) (KiCad packages3D, STEP)
  • 3D model files: mp6543cgl-z-etched.step / mp6543cgl-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mp6543cgl-z.step / mp6543cgl-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (19 pp, sha256 a30f8d3f01afa1c5, retrieved 2026-10-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF