3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMP6543CGL-Z
Monolithic Power Systems · Motor Driver ICs · QFN-24(3x4)
MP6543CGL-Z from Monolithic Power Systems, in a QFN-24(3x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ENB | input | Phase B enable input; when low the phase B outputs are Hi-Z and PWMB is ignored, with an internal weak pull-down. |
| 2 | ENC | input | Phase C enable input; when low the phase C outputs are Hi-Z and PWMC is ignored, with an internal weak pull-down. |
| 3 | PWMA | input | Phase A pulse-width modulation (PWM) input that sets SA to VIN when high and GND when low while ENA is high. |
| 4 | PWMB | input | Phase B PWM input that sets SB to VIN when high and GND when low while ENB is high. |
| 5 | PWMC | input | Phase C PWM input that sets SC to VIN when high and GND when low while ENC is high. |
| 6 | VIN | power_in | Input supply voltage, 3V to 22V operating (25V absolute maximum), needing a bypass capacitor on each VIN pin. |
| 7 | SA | output | Phase A half-bridge output. |
| 8 | LSSA | passive | Phase A low-side MOSFET (LS-FET) source connection, which can go to an external shunt resistor (-0.3V to +0.3V relative to GND). |
| 9 | SB | output | Phase B half-bridge output. |
| 10 | LSSB | passive | Phase B LS-FET source connection, which can go to an external shunt resistor (-0.3V to +0.3V relative to GND). |
| 11 | SC | output | Phase C half-bridge output. |
| 12 | LSSC | passive | Phase C LS-FET source connection, which can go to an external shunt resistor (-0.3V to +0.3V relative to GND). |
| 13 | VIN | power_in | Input supply voltage, 3V to 22V operating (25V absolute maximum), needing a bypass capacitor on each VIN pin. |
| 14 | VCP | power_out | Charge pump output; connect VCP to VIN with a 1µF, 16V X7R ceramic capacitor (typically VIN + 3.3V). |
| 15 | GND | power_in | Ground. |
| 16 | VIN_LDO | power_in | LDO input, 3V to 22V. |
| 17 | OC_ADJ | input | Over-current protection (OCP) configurable current limit pin; the OCP threshold is typically 5A with ROCP = 0 and 7A when floating. |
| 18 | V3P3 | power_out | 3.3V regulator output (100mA) and LS-FET gate driver supply voltage; bypass to GND with a 4.7µF capacitor. |
| 19 | nFAULT | output | Open-drain fault indicator that is logic low when a fault occurs and needs an external pull-up resistor. |
| 20 | SOC | output | Phase C current-sense output that sources or sinks a current of 1/4000 of the phase C LS-FET current. |
| 21 | SOB | output | Phase B current-sense output that sources or sinks a current of 1/4000 of the phase B LS-FET current. |
| 22 | SOA | output | Phase A current-sense output that sources or sinks a current of 1/4000 of the phase A LS-FET current. |
| 23 | nSLEEP | input | Sleep mode input; pull low to enter low-power sleep mode and high to exit, with an internal pull-down resistor. |
| 24 | ENA | input | Phase A enable input; when low the phase A outputs are Hi-Z and PWMA is ignored, with an internal weak pull-down. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-24(3x4) |
| Category | Power Management |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 3 | 22 | V | 5 | ||
| LDO input voltage | VIN_LDO | 3 | 22 | V | 5 | ||
| Quiescent current | IQ | 2.5 | 3.2 | mA | nSLEEP = 1, ENx = 0 | 5 | |
| Sleep current | ISLEEP | 45 | 60 | µA | nSLEEP = 0 | 5 | |
| Input logic low threshold | VIN_LOW | 0.4 | V | 5 | |||
| Input logic high threshold | VIN_HIGH | 1.5 | V | 5 | |||
| Logic input current high | IIN_HIGH | -20 | 20 | µA | V = 3.3V | 5 | |
| Logic input current low | IIN_LOW | -20 | 20 | µA | V = 0V | 5 | |
| LDO output | V3P3 | 3.2 | 3.32 | 3.45 | V | IOUT = 0mA to 80mA | 5 |
| UVLO threshold | VUVLO | 2.5 | 2.7 | 2.9 | V | VIN rising | 5 |
| OCP threshold | IOCP | 4 | 5 | 6.5 | A | ROCP = 0 | 5 |
| OCP threshold | IOCP | 4.8 | 7 | 8.8 | A | ROCP is floating | 5 |
| CS output current | 225 | 250 | 275 | µA | ILS-FET = 1A | 5 | |
| CS output current | -275 | -250 | -225 | µA | ILS-FET = -1A | 5 | |
| CS output current | 22.5 | 25 | 27.5 | µA | ILS-FET = 100mA | 5 | |
| CS output current | -27.5 | -25 | -22.5 | µA | ILS-FET = -100mA | 5 | |
| Positive-to-negative ratio | 95 | 105 | % | ILS-FET = ±1A, ±100mA | 5 | ||
| Phase-to-phase ratio | 95 | 105 | % | ILS-FET = ±1A, ±100mA | 5 | ||
| CS output voltage swing | 0 | 3.6 | V | ILS-FET = ±0.25A | 5 | ||
| HS-FET on resistance | RDS(ON)_HS | 90 | 115 | 135 | mΩ | IOUT = 1A | 5 |
| LS-FET on resistance | RDS(ON)_LS | 85 | 110 | 125 | mΩ | IOUT = 1A | 5 |
| Start-up delay | tDELAY_SU | 1.5 | ms | VIN is rising or VnSLEEP is rising | 5 | ||
| Internal pull-down resistance | RPD | 500 | kΩ | All logic inputs | 5 | ||
| nFAULT pull-down resistance | RDS(ON)_nFAULT | 15 | Ω | 5 | |||
| UVLO hysteresis | ∆VUVLO | 150 | mV | 5 | |||
| OCP deglitch time | tOCP | 1 | µs | 5 | |||
| Thermal shutdown | TTSD | 160 | °C | TJ rising; not tested in production | 5 | ||
| Thermal shutdown hysteresis | ∆TTSD | 25 | °C | Not tested in production | 5 | ||
| Output rise time | 25 | ns | RLOAD = 50Ω; not tested in production | 5 | |||
| Output fall time | 25 | ns | RLOAD = 50Ω; not tested in production | 5 | |||
| Dead time | 40 | ns | RLOAD = 50Ω; not tested in production | 5 | |||
| PWMx to Sx delay time rising | 70 | ns | Not tested in production | 6 | |||
| PWMx to Sx delay time falling | 70 | ns | Not tested in production | 6 | |||
| Supply voltage (VIN, VIN_LDO) | -0.3 | 25 | V | 4 | |||
| LSSx to GND | -0.3 | 0.3 | V | 4 | |||
| All other pins | -0.3 | 5 | V | 4 | |||
| Continuous power dissipation | 2.6 | W | TA = 25°C, QFN-24 (3mmx4mm) | 4 | |||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Storage temperature | -65 | 150 | °C | 4 | |||
| ESD HBM | -2 | 2 | kV | Human body model | 4 | ||
| ESD CDM | -2 | 2 | kV | Charged device model | 4 | ||
| Supply voltage | VIN | 3 | 22 | V | 4 | ||
| Output current | IOUT | 1.2 | A | Continuous current depends on PCB layout and ambient temperature | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Thermal resistance junction-to-case | θJC | 10 | °C/W | QFN-24 (3mmx4mm), JESD51-7 4-layer PCB | 4 |
CAD (KiCad official)
- Symbol:
MP6543CGL-Z - Footprint:
Package_DFN_QFN:QFN-24-1EP_3x4mm_P0.4mm_EP1.65x2.65mm - 3D model: QFN-24(3x4) (KiCad packages3D, STEP)
- 3D model files:
mp6543cgl-z-etched.step/mp6543cgl-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp6543cgl-z.step/mp6543cgl-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (19 pp, sha256
a30f8d3f01afa1c5, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).