Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PIC16F84-04

Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOIC-18-300mil

PIC16F84-04 from Microchip Tech, in a SOIC-18-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RA2 bidirectional PORTA bidirectional I/O pin with TTL input levels and full CMOS output drivers; direction is set by TRISA<2>.
2 RA3 bidirectional PORTA bidirectional I/O pin with TTL input levels and full CMOS output drivers; direction is set by TRISA<3>.
3 RA4/T0CKI bidirectional PORTA bidirectional I/O pin with Schmitt Trigger input that can also serve as the TMR0 clock input; the output is open drain.
4 MCLR input Active-low master clear (reset) input with Schmitt Trigger buffer, which also receives the programming voltage VIHH during programming.
5 VSS power_in Ground reference for logic and I/O pins.
6 RB0/INT bidirectional PORTB bidirectional I/O pin with TTL input (Schmitt Trigger when used as external interrupt INT) and software-programmable weak pull-up.
7 RB1 bidirectional PORTB bidirectional I/O pin with TTL input levels and software-programmable weak pull-up.
8 RB2 bidirectional PORTB bidirectional I/O pin with TTL input levels and software-programmable weak pull-up.
9 RB3 bidirectional PORTB bidirectional I/O pin with TTL input levels and software-programmable weak pull-up.
10 RB4 bidirectional PORTB bidirectional I/O pin with TTL input levels, software-programmable weak pull-up, and interrupt-on-change capability.
11 RB5 bidirectional PORTB bidirectional I/O pin with TTL input levels, software-programmable weak pull-up, and interrupt-on-change capability.
12 RB6 bidirectional PORTB bidirectional I/O pin with interrupt-on-change capability; it is the serial programming clock with Schmitt Trigger input in programming mode.
13 RB7 bidirectional PORTB bidirectional I/O pin with interrupt-on-change capability; it is the serial programming data pin with Schmitt Trigger input in programming mode.
14 VDD power_in Positive supply for logic and I/O pins; 4.0 V to 6.0 V for XT, RC and LP oscillator configurations and 4.5 V to 5.5 V for HS (PIC16F84 standard range).
15 OSC2/CLKOUT output Oscillator crystal output connecting to the crystal or resonator in crystal mode; in RC mode it outputs CLKOUT at 1/4 the OSC1 frequency.
16 OSC1/CLKIN input Oscillator crystal input or external clock source input; Schmitt Trigger input in RC mode and CMOS input otherwise.
17 RA0 bidirectional PORTA bidirectional I/O pin with TTL input levels and full CMOS output drivers; direction is set by TRISA<0>.
18 RA1 bidirectional PORTA bidirectional I/O pin with TTL input levels and full CMOS output drivers; direction is set by TRISA<1>.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-18-300mil
Category Single Chip Microcomputer/Microcontroller
Pins 18

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient temperature under bias -55 125 °C 75
Storage temperature -65 150 °C 75
Voltage on VDD with respect to VSS VDD -0.3 7.5 V 75
Voltage on MCLR with respect to VSS -0.3 14 V Note 2 75
Voltage on any pin with respect to VSS (except VDD and MCLR) -0.6 V Maximum printed as VDD + 0.6V; not numeric 75
Maximum current out of VSS pin 150 mA 75
Maximum current into VDD pin 100 mA 75
Input clamp current IIK 20 mA VI < 0 or VI > VDD 75
Output clamp current IOK 20 mA VO < 0 or VO > VDD 75
Maximum output current sourced by any I/O pin 20 mA 75
Maximum current sunk by PORTA 80 mA 75
Maximum current sourced by PORTA 50 mA 75
Maximum current sunk by PORTB 150 mA 75
Maximum current sourced by PORTB 100 mA 75
Operating temperature range (commercial) TA 0 70 °C Commercial 77
VDD supply voltage VDD 4 6 V XT, RC and LP osc configuration 77
VDD supply voltage (HS) VDD 4.5 5.5 V HS osc configuration 77
RAM data retention voltage VDR 1.5 V Device in SLEEP mode 77
VDD rise rate to ensure internal Power-on Reset signal SVDD 0.05 V/ms See section on Power-on Reset for details 77
Supply current (IDD) IDD 1.8 4.5 mA RC and XT osc configuration; FOSC = 4.0 MHz, VDD = 5.5V 77
Supply current during Flash programming IDD 7.3 10 mA FOSC = 4.0 MHz, VDD = 5.5V (during Flash programming) 77
Power-down current (IPD) IPD 1 14 µA VDD = 4.0V, WDT disabled, commercial 77
Input low voltage, I/O ports with TTL buffer VIL 0.8 V 4.5 V ≤ VDD ≤ 5.5 V 79
Input high voltage, I/O ports with TTL buffer VIH 2.4 V 4.5 V ≤ VDD ≤ 5.5 V 79
PORTB weak pull-up current IPURB 50 250 400 µA AVDD = 5.0V, VPIN = VSS 79
Input leakage current, I/O ports IIL 1 µA VSS ≤ VPIN ≤ VDD, pin at hi-impedance 79
Input leakage current, MCLR and RA4/T0CKI IIL 5 µA VSS ≤ VPIN ≤ VDD 79
Input leakage current, OSC1 IIL 5 µA VSS ≤ VPIN ≤ VDD, XT, HS and LP osc configuration 79
Output low voltage, I/O ports VOL 0.6 V IOL = 8.5 mA, VDD = 4.5V 79
Output low voltage, OSC2/CLKOUT VOL 0.6 V IOL = 1.6 mA, VDD = 4.5V 79
Capacitive loading on OSC2 pin COSC2 15 pF XT, HS and LP modes when external clock is used to drive OSC1 80
Capacitive loading on all I/O pins and OSC2 (RC mode) CIO 50 pF 80
Data EEPROM endurance ED 1 10 M E/W 25°C at 5V 80
VDD for data EEPROM read/write VDRW 6 V VMIN = Minimum operating voltage 80
Data EEPROM erase/write cycle time TDEW 10 20 ms 80
Program Flash endurance EP 100 1000 E/W 80
VDD for Flash read VPR 6 V VMIN = Minimum operating voltage 80
VDD for Flash erase/write VPEW 4.5 5.5 V 80
External CLKIN frequency FOSC 4 MHz XT, RC osc PIC16F8X-04 82
Oscillator frequency (RC) FOSC 4 MHz RC osc PIC16F8X-04 82
Oscillator frequency (XT) FOSC 0.1 4 MHz XT osc PIC16F8X-04 82
External CLKIN period Tosc 250 ns XT, RC osc PIC16F8X-04 82
Oscillator period (RC) Tosc 250 ns RC osc PIC16F8X-04 82
Oscillator period (XT) Tosc 250 10000 ns XT osc PIC16F8X-04 82
Instruction cycle time 2TCY 0.4 µs Note 1 82
Clock in (OSC1) high or low time TosL, TosH 50 ns XT osc PIC16F8X-04 82
Clock in (OSC1) rise or fall time TosR, TosF 25 ns XT osc PIC16F8X-04 82
OSC1 to CLKOUT (falling) TosH2ckL 15 30 ns PIC16F8X; Note 1 (RC mode) 83
OSC1 to CLKOUT (rising) TosH2ckH 15 30 ns PIC16F8X; Note 1 (RC mode) 83
CLKOUT rise time TckR 15 30 ns PIC16F8X; Note 1 83
CLKOUT fall time TckF 15 30 ns PIC16F8X; Note 1 83
Port in hold after CLKOUT TckH2ioI 0 ns Note 1 83
OSC1 (Q1 cycle) to port out valid TosH2ioV 125 ns PIC16F8X 83
OSC1 (Q2 cycle) to port input invalid (I/O in hold time) TosH2ioI 10 ns PIC16F8X 83
Port input valid to OSC1 (I/O in setup time) TioV2osH -75 ns PIC16F8X 83
Port output rise time TioR 10 35 ns PIC16F8X 83
Port output fall time TioF 10 35 ns PIC16F8X 83
INT pin high or low time Tinp 20 ns PIC16F8X 83

CAD (KiCad official)

  • Symbol: PIC16F84-04
  • Footprint: Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm
  • 3D model: SOIC-18-300mil (KiCad packages3D, STEP)
  • 3D model files: pic16f84-04-so-etched.step / pic16f84-04-so-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pic16f84-04-so.step / pic16f84-04-so.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (128 pp, sha256 d8643281e8b7d47e, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF