3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPIC16F84-04
Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOIC-18-300mil
PIC16F84-04 from Microchip Tech, in a SOIC-18-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RA2 | bidirectional | PORTA bidirectional I/O pin with TTL input levels and full CMOS output drivers; direction is set by TRISA<2>. |
| 2 | RA3 | bidirectional | PORTA bidirectional I/O pin with TTL input levels and full CMOS output drivers; direction is set by TRISA<3>. |
| 3 | RA4/T0CKI | bidirectional | PORTA bidirectional I/O pin with Schmitt Trigger input that can also serve as the TMR0 clock input; the output is open drain. |
| 4 | MCLR | input | Active-low master clear (reset) input with Schmitt Trigger buffer, which also receives the programming voltage VIHH during programming. |
| 5 | VSS | power_in | Ground reference for logic and I/O pins. |
| 6 | RB0/INT | bidirectional | PORTB bidirectional I/O pin with TTL input (Schmitt Trigger when used as external interrupt INT) and software-programmable weak pull-up. |
| 7 | RB1 | bidirectional | PORTB bidirectional I/O pin with TTL input levels and software-programmable weak pull-up. |
| 8 | RB2 | bidirectional | PORTB bidirectional I/O pin with TTL input levels and software-programmable weak pull-up. |
| 9 | RB3 | bidirectional | PORTB bidirectional I/O pin with TTL input levels and software-programmable weak pull-up. |
| 10 | RB4 | bidirectional | PORTB bidirectional I/O pin with TTL input levels, software-programmable weak pull-up, and interrupt-on-change capability. |
| 11 | RB5 | bidirectional | PORTB bidirectional I/O pin with TTL input levels, software-programmable weak pull-up, and interrupt-on-change capability. |
| 12 | RB6 | bidirectional | PORTB bidirectional I/O pin with interrupt-on-change capability; it is the serial programming clock with Schmitt Trigger input in programming mode. |
| 13 | RB7 | bidirectional | PORTB bidirectional I/O pin with interrupt-on-change capability; it is the serial programming data pin with Schmitt Trigger input in programming mode. |
| 14 | VDD | power_in | Positive supply for logic and I/O pins; 4.0 V to 6.0 V for XT, RC and LP oscillator configurations and 4.5 V to 5.5 V for HS (PIC16F84 standard range). |
| 15 | OSC2/CLKOUT | output | Oscillator crystal output connecting to the crystal or resonator in crystal mode; in RC mode it outputs CLKOUT at 1/4 the OSC1 frequency. |
| 16 | OSC1/CLKIN | input | Oscillator crystal input or external clock source input; Schmitt Trigger input in RC mode and CMOS input otherwise. |
| 17 | RA0 | bidirectional | PORTA bidirectional I/O pin with TTL input levels and full CMOS output drivers; direction is set by TRISA<0>. |
| 18 | RA1 | bidirectional | PORTA bidirectional I/O pin with TTL input levels and full CMOS output drivers; direction is set by TRISA<1>. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-18-300mil |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 18 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient temperature under bias | -55 | 125 | °C | 75 | |||
| Storage temperature | -65 | 150 | °C | 75 | |||
| Voltage on VDD with respect to VSS | VDD | -0.3 | 7.5 | V | 75 | ||
| Voltage on MCLR with respect to VSS | -0.3 | 14 | V | Note 2 | 75 | ||
| Voltage on any pin with respect to VSS (except VDD and MCLR) | -0.6 | V | Maximum printed as VDD + 0.6V; not numeric | 75 | |||
| Maximum current out of VSS pin | 150 | mA | 75 | ||||
| Maximum current into VDD pin | 100 | mA | 75 | ||||
| Input clamp current | IIK | 20 | mA | VI < 0 or VI > VDD | 75 | ||
| Output clamp current | IOK | 20 | mA | VO < 0 or VO > VDD | 75 | ||
| Maximum output current sourced by any I/O pin | 20 | mA | 75 | ||||
| Maximum current sunk by PORTA | 80 | mA | 75 | ||||
| Maximum current sourced by PORTA | 50 | mA | 75 | ||||
| Maximum current sunk by PORTB | 150 | mA | 75 | ||||
| Maximum current sourced by PORTB | 100 | mA | 75 | ||||
| Operating temperature range (commercial) | TA | 0 | 70 | °C | Commercial | 77 | |
| VDD supply voltage | VDD | 4 | 6 | V | XT, RC and LP osc configuration | 77 | |
| VDD supply voltage (HS) | VDD | 4.5 | 5.5 | V | HS osc configuration | 77 | |
| RAM data retention voltage | VDR | 1.5 | V | Device in SLEEP mode | 77 | ||
| VDD rise rate to ensure internal Power-on Reset signal | SVDD | 0.05 | V/ms | See section on Power-on Reset for details | 77 | ||
| Supply current (IDD) | IDD | 1.8 | 4.5 | mA | RC and XT osc configuration; FOSC = 4.0 MHz, VDD = 5.5V | 77 | |
| Supply current during Flash programming | IDD | 7.3 | 10 | mA | FOSC = 4.0 MHz, VDD = 5.5V (during Flash programming) | 77 | |
| Power-down current (IPD) | IPD | 1 | 14 | µA | VDD = 4.0V, WDT disabled, commercial | 77 | |
| Input low voltage, I/O ports with TTL buffer | VIL | 0.8 | V | 4.5 V ≤ VDD ≤ 5.5 V | 79 | ||
| Input high voltage, I/O ports with TTL buffer | VIH | 2.4 | V | 4.5 V ≤ VDD ≤ 5.5 V | 79 | ||
| PORTB weak pull-up current | IPURB | 50 | 250 | 400 | µA | AVDD = 5.0V, VPIN = VSS | 79 |
| Input leakage current, I/O ports | IIL | 1 | µA | VSS ≤ VPIN ≤ VDD, pin at hi-impedance | 79 | ||
| Input leakage current, MCLR and RA4/T0CKI | IIL | 5 | µA | VSS ≤ VPIN ≤ VDD | 79 | ||
| Input leakage current, OSC1 | IIL | 5 | µA | VSS ≤ VPIN ≤ VDD, XT, HS and LP osc configuration | 79 | ||
| Output low voltage, I/O ports | VOL | 0.6 | V | IOL = 8.5 mA, VDD = 4.5V | 79 | ||
| Output low voltage, OSC2/CLKOUT | VOL | 0.6 | V | IOL = 1.6 mA, VDD = 4.5V | 79 | ||
| Capacitive loading on OSC2 pin | COSC2 | 15 | pF | XT, HS and LP modes when external clock is used to drive OSC1 | 80 | ||
| Capacitive loading on all I/O pins and OSC2 (RC mode) | CIO | 50 | pF | 80 | |||
| Data EEPROM endurance | ED | 1 | 10 | M E/W | 25°C at 5V | 80 | |
| VDD for data EEPROM read/write | VDRW | 6 | V | VMIN = Minimum operating voltage | 80 | ||
| Data EEPROM erase/write cycle time | TDEW | 10 | 20 | ms | 80 | ||
| Program Flash endurance | EP | 100 | 1000 | E/W | 80 | ||
| VDD for Flash read | VPR | 6 | V | VMIN = Minimum operating voltage | 80 | ||
| VDD for Flash erase/write | VPEW | 4.5 | 5.5 | V | 80 | ||
| External CLKIN frequency | FOSC | 4 | MHz | XT, RC osc PIC16F8X-04 | 82 | ||
| Oscillator frequency (RC) | FOSC | 4 | MHz | RC osc PIC16F8X-04 | 82 | ||
| Oscillator frequency (XT) | FOSC | 0.1 | 4 | MHz | XT osc PIC16F8X-04 | 82 | |
| External CLKIN period | Tosc | 250 | ns | XT, RC osc PIC16F8X-04 | 82 | ||
| Oscillator period (RC) | Tosc | 250 | ns | RC osc PIC16F8X-04 | 82 | ||
| Oscillator period (XT) | Tosc | 250 | 10000 | ns | XT osc PIC16F8X-04 | 82 | |
| Instruction cycle time | 2TCY | 0.4 | µs | Note 1 | 82 | ||
| Clock in (OSC1) high or low time | TosL, TosH | 50 | ns | XT osc PIC16F8X-04 | 82 | ||
| Clock in (OSC1) rise or fall time | TosR, TosF | 25 | ns | XT osc PIC16F8X-04 | 82 | ||
| OSC1 to CLKOUT (falling) | TosH2ckL | 15 | 30 | ns | PIC16F8X; Note 1 (RC mode) | 83 | |
| OSC1 to CLKOUT (rising) | TosH2ckH | 15 | 30 | ns | PIC16F8X; Note 1 (RC mode) | 83 | |
| CLKOUT rise time | TckR | 15 | 30 | ns | PIC16F8X; Note 1 | 83 | |
| CLKOUT fall time | TckF | 15 | 30 | ns | PIC16F8X; Note 1 | 83 | |
| Port in hold after CLKOUT | TckH2ioI | 0 | ns | Note 1 | 83 | ||
| OSC1 (Q1 cycle) to port out valid | TosH2ioV | 125 | ns | PIC16F8X | 83 | ||
| OSC1 (Q2 cycle) to port input invalid (I/O in hold time) | TosH2ioI | 10 | ns | PIC16F8X | 83 | ||
| Port input valid to OSC1 (I/O in setup time) | TioV2osH | -75 | ns | PIC16F8X | 83 | ||
| Port output rise time | TioR | 10 | 35 | ns | PIC16F8X | 83 | |
| Port output fall time | TioF | 10 | 35 | ns | PIC16F8X | 83 | |
| INT pin high or low time | Tinp | 20 | ns | PIC16F8X | 83 |
CAD (KiCad official)
- Symbol:
PIC16F84-04 - Footprint:
Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm - 3D model: SOIC-18-300mil (KiCad packages3D, STEP)
- 3D model files:
pic16f84-04-so-etched.step/pic16f84-04-so-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic16f84-04-so.step/pic16f84-04-so.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (128 pp, sha256
d8643281e8b7d47e, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).