Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SI4468-A2A-IMR

SILICON LABS · RF Transceiver ICs · QFN-20-EP(4x4)

SI4468-A2A-IMR from SILICON LABS, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SDN input Shutdown input (0-VDD V digital); SDN must be 0 in all modes except Shutdown, and SDN = 1 fully shuts the chip down and loses register contents.
2 RXp input Differential RF input pin of the LNA; use the application schematic for the example matching network.
3 RXn input Differential RF input pin of the LNA; use the application schematic for the example matching network.
4 TX output PA output is an open-drain connection, so the L-C match must supply VDD (+3.3 VDC nominal) to this pin.
5 NC unconnected Not connected internally to any circuitry; datasheet recommends connecting to GND per the reference design schematic.
6 VDD power_in Supply input to the internal regulators, +1.8 to +3.8 V; recommended supply is +3.3 V.
7 TXRAMP output Programmable bias output with ramp capability for an external FET PA (see Section 5.4, Transmitter).
8 VDD power_in Supply input to the internal regulators, +1.8 to +3.8 V; recommended supply is +3.3 V.
9 GPIO0 bidirectional General-purpose digital I/O configurable for functions such as MCU clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control.
10 GPIO1 bidirectional General-purpose digital I/O configurable for functions such as MCU clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control.
11 nIRQ output General microcontroller interrupt status output that goes low when any interrupt event occurs; no external pull-up is required, though one may be desirable with multiple interrupt lines.
12 SCLK input Serial clock input (0-VDD V digital) for the 4-line serial bus; data is clocked into the device on positive edge transitions.
13 SDO output Serial readback output (0-VDD V digital) that provides readback of the internal control registers.
14 SDI input Serial data input (0-VDD V digital) providing the serial data stream for the 4-line serial bus.
15 nSEL input Serial interface select input (0-VDD V digital) providing the Select/Enable function for the 4-line serial bus.
16 XOUT output Crystal oscillator output; connect to an external 25 to 32 MHz crystal, or leave floating when driving with an external source on XIN.
17 XIN input Crystal oscillator input; connect to an external 25 to 32 MHz crystal or to an external source.
18 GND power_in When using a crystal leave floating per the reference design; when using a TCXO connect to TCXO GND, which should be separate from the board's reference ground plane.
19 GPIO2 bidirectional General-purpose digital I/O configurable for functions such as MCU clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control.
20 GPIO3 bidirectional General-purpose digital I/O configurable for functions such as MCU clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control.
21 PADDLE_GND passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer SILICON LABS
Package QFN-20-EP(4x4)
Category RF & Radio
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage Range VDD 1.8 3.3 3.8 V 4
Shutdown Current IShutdown 30 1300 nA RC Oscillator, Main Digital Regulator, and Low Power Digital Regulator OFF 4
Standby Current IStandby 40 2900 nA Register values maintained and RC oscillator/WUT OFF 4
Sleep Current (RC) ISleepRC 740 3800 nA RC Oscillator/WUT ON and all register values maintained, and all other blocks OFF 4
RX Mode Current (High Performance Mode) IRXH 13.7 22 mA High Performance Mode; measured at 915 MHz and 40 kbps 4
TX Mode Current (Si4468), +20 dBm ITX_+20 88 108 mA +20 dBm output power, Class-E match, 915 MHz, 3.3 V 4
TX Mode Current (Si4468), +20 dBm ITX_+20 68.5 80 mA +20 dBm output power, square-wave match, 169 MHz, 3.3 V 4
TX Mode Current (Si4468), +13 dBm ITX_+13 44.5 60 mA +13 dBm output power, Class-E match, 915 MHz, 3.3 V 4
Synthesizer Frequency Range (850-1050 MHz band) FSYN 850 1050 MHz 5
Synthesizer Frequency Range (350-525 MHz band) FSYN 350 525 MHz 5
Synthesizer Frequency Range (284-350 MHz band) FSYN 284 350 MHz 5
Synthesizer Frequency Range (142-175 MHz band) FSYN 142 175 MHz 5
RX Sensitivity 169 MHz (BER < 0.1%) PRX_40 -110 -108 dBm 40 kbps, GFSK, BT = 0.5, f= 20 kHz 6
RX Sensitivity 169 MHz (BER < 0.1%) PRX_100 -106 -104 dBm 100 kbps, GFSK, BT = 0.5, f= 50 kHz 6
RX Sensitivity 169 MHz (BER < 0.1%) PRX_500 -98 -96 dBm 500 kbps, GFSK, BT = 0.5, f= 250 kHz 6
RX Sensitivity 169 MHz (BER < 0.1%) PRX_OOK -110 -107 dBm BER < 0.1%, 4.8 kbps, 350 kHz BW, OOK, PN15 data 6
RX Sensitivity 169 MHz (BER < 0.1%) PRX_OOK -103 -100 dBm BER < 0.1%, 40 kbps, 350 kHz BW, OOK, PN15 data 6
RX Sensitivity 169 MHz (BER < 0.1%) PRX_OOK -97 -93 dBm BER < 0.1%, 120 kbps, 350 kHz BW, OOK, PN15 data 6
RX Sensitivity 915/868 MHz (BER < 0.1%) PRX_40 -109 -107 dBm 40 kbps, GFSK, BT = 0.5, f= 20 kHz 7
RX Sensitivity 915/868 MHz (BER < 0.1%) PRX_100 -104 -102 dBm 100 kbps, GFSK, BT = 0.5, f= 50 kHz 7
RX Sensitivity 915/868 MHz (BER < 0.1%) PRX_500 -97 -92 dBm 500 kbps, GFSK, BT = 0.5, f= 250 kHz 7
RX Sensitivity 915/868 MHz (BER < 0.1%) PRX_OOK -108 -104 dBm BER < 0.1%, 4.8 kbps, 350 kHz BW, OOK, PN15 data 7
RX Sensitivity 915/868 MHz (BER < 0.1%) PRX_OOK -101 -97 dBm BER < 0.1%, 40 kbps, 350 kHz BW, OOK, PN15 data 7
RX Sensitivity 915/868 MHz (BER < 0.1%) PRX_OOK -96 -91 dBm BER < 0.1%, 120 kbps, 350 kHz BW, OOK, PN15 data 7
RX Channel Bandwidth BW 0.2 850 kHz 7
1-Ch Offset Selectivity 169 MHz C/I1-CH -69 -59 dB Desired 3 dB above sensitivity, BER < 0.1%, CW interferer 7
1-Ch Offset Selectivity 450 MHz C/I1-CH -60 -50 dB Desired 3 dB above sensitivity, BER < 0.1%, CW interferer 7
1-Ch Offset Selectivity 868/915 MHz C/I1-CH -55 -45 dB Desired 3 dB above sensitivity, BER < 0.1%, CW interferer 7
Blocking 1 MHz Offset 1MBLOCK -79 -68 dB Desired 3 dB above sensitivity, BER = 0.1%, CW interferer 7
Blocking 8 MHz Offset 8MBLOCK -86 -75 dB Desired 3 dB above sensitivity, BER = 0.1%, CW interferer 7
Image Rejection (IF = 468.75 kHz), no calibration ImREJ 30 40 dB No image rejection calibration; RF = 460 MHz 8
Image Rejection (IF = 468.75 kHz), with calibration ImREJ 40 55 dB With image rejection calibration; RF = 460 MHz 8
Image Rejection (IF = 468.75 kHz), no calibration ImREJ 30 45 dB No image rejection calibration; RF = 915 MHz 8
Image Rejection (IF = 468.75 kHz), with calibration ImREJ 40 52 dB With image rejection calibration; RF = 915 MHz 8
Image Rejection (IF = 468.75 kHz), no calibration ImREJ 35 45 dB No image rejection calibration; RF = 169 MHz 8
Image Rejection (IF = 468.75 kHz), with calibration ImREJ 45 60 dB With image rejection calibration; RF = 169 MHz 8
(G)FSK Data Rate DRFSK 0.1 500 kbps 9
4(G)FSK Data Rate DR4FSK 0.2 1000 kbps 9
OOK Data Rate DROOK 0.1 120 kbps 9
Output Power Range (Si4468) PTX68 -20 20 dBm Typical range at 3.3 V 9
Output Power Variation (Si4468), 915 MHz 19 20 21 dBm At 20 dBm PA power setting, 915 MHz, Class E match, 3.3 V, 25 °C 9
Output Power Variation (Si4468), 169 MHz 18.5 20 21 dBm At 20 dBm PA power setting, 169 MHz, Square Wave match, 3.3 V, 25 °C 10
TX RF Output Steps PRF_OUT 0.25 0.4 dB Within 6 dB of max power, switched current or CLE match 10
TX RF Output Level Variation vs. Temperature PRF_TEMP 2.3 3 dB -40 to +85 C 10
TX RF Output Level Variation vs. Frequency PRF_FREQ 0.6 1.7 dB Measured across 902-928 MHz 10
Microcontroller Clock Output Frequency Range FMC 32.768 kHz Configurable to Fxtal or Fxtal divided by 2, 3, 7.5, 10, 15, or 30; 32.768 kHz also supported 11
XTAL Range XTALRange 25 32 MHz 11
POR Reset Time tPOR 6 ms 11
Input Current IIN -1 1 µA 0<VIN< VDD 12
Input Current If Pullup is Activated IINP 1 4 µA VIL = 0 V 12
Operating Ambient Temperature Range TA -40 125 °C 13
Thermal Impedance Junction to Ambient JA 25 °C/w Based on RF evaluation board measurements 13
Junction Temperature Maximum Value Tj 137 °C Based on RF evaluation board measurements 13
Storage Temperature Range TSTG -55 150 °C 13
VDD to GND VDD -0.3 3.8 V 13
Instantaneous VRF-peak to GND on TX Output Pin VRF-peak -0.3 8 V 13
Sustained VRF-peak to GND on TX Output Pin VRF-peak -0.3 6.5 V 13
Voltage on Analog Inputs -0.7 V 13
RX Input Power 10 dBm 13

CAD (KiCad official)

  • Symbol: SI4468-A2A-IMR
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: si4468-a2a-imr-etched.step / si4468-a2a-imr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); si4468-a2a-imr.step / si4468-a2a-imr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SILICON LABS datasheet (57 pp, sha256 e717e10d43adad92, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF