3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSI4468-A2A-IMR
SILICON LABS · RF Transceiver ICs · QFN-20-EP(4x4)
SI4468-A2A-IMR from SILICON LABS, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDN | input | Shutdown input (0-VDD V digital); SDN must be 0 in all modes except Shutdown, and SDN = 1 fully shuts the chip down and loses register contents. |
| 2 | RXp | input | Differential RF input pin of the LNA; use the application schematic for the example matching network. |
| 3 | RXn | input | Differential RF input pin of the LNA; use the application schematic for the example matching network. |
| 4 | TX | output | PA output is an open-drain connection, so the L-C match must supply VDD (+3.3 VDC nominal) to this pin. |
| 5 | NC | unconnected | Not connected internally to any circuitry; datasheet recommends connecting to GND per the reference design schematic. |
| 6 | VDD | power_in | Supply input to the internal regulators, +1.8 to +3.8 V; recommended supply is +3.3 V. |
| 7 | TXRAMP | output | Programmable bias output with ramp capability for an external FET PA (see Section 5.4, Transmitter). |
| 8 | VDD | power_in | Supply input to the internal regulators, +1.8 to +3.8 V; recommended supply is +3.3 V. |
| 9 | GPIO0 | bidirectional | General-purpose digital I/O configurable for functions such as MCU clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 10 | GPIO1 | bidirectional | General-purpose digital I/O configurable for functions such as MCU clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 11 | nIRQ | output | General microcontroller interrupt status output that goes low when any interrupt event occurs; no external pull-up is required, though one may be desirable with multiple interrupt lines. |
| 12 | SCLK | input | Serial clock input (0-VDD V digital) for the 4-line serial bus; data is clocked into the device on positive edge transitions. |
| 13 | SDO | output | Serial readback output (0-VDD V digital) that provides readback of the internal control registers. |
| 14 | SDI | input | Serial data input (0-VDD V digital) providing the serial data stream for the 4-line serial bus. |
| 15 | nSEL | input | Serial interface select input (0-VDD V digital) providing the Select/Enable function for the 4-line serial bus. |
| 16 | XOUT | output | Crystal oscillator output; connect to an external 25 to 32 MHz crystal, or leave floating when driving with an external source on XIN. |
| 17 | XIN | input | Crystal oscillator input; connect to an external 25 to 32 MHz crystal or to an external source. |
| 18 | GND | power_in | When using a crystal leave floating per the reference design; when using a TCXO connect to TCXO GND, which should be separate from the board's reference ground plane. |
| 19 | GPIO2 | bidirectional | General-purpose digital I/O configurable for functions such as MCU clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 20 | GPIO3 | bidirectional | General-purpose digital I/O configurable for functions such as MCU clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 21 | PADDLE_GND | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-20-EP(4x4) |
| Category | RF & Radio |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | VDD | 1.8 | 3.3 | 3.8 | V | 4 | |
| Shutdown Current | IShutdown | 30 | 1300 | nA | RC Oscillator, Main Digital Regulator, and Low Power Digital Regulator OFF | 4 | |
| Standby Current | IStandby | 40 | 2900 | nA | Register values maintained and RC oscillator/WUT OFF | 4 | |
| Sleep Current (RC) | ISleepRC | 740 | 3800 | nA | RC Oscillator/WUT ON and all register values maintained, and all other blocks OFF | 4 | |
| RX Mode Current (High Performance Mode) | IRXH | 13.7 | 22 | mA | High Performance Mode; measured at 915 MHz and 40 kbps | 4 | |
| TX Mode Current (Si4468), +20 dBm | ITX_+20 | 88 | 108 | mA | +20 dBm output power, Class-E match, 915 MHz, 3.3 V | 4 | |
| TX Mode Current (Si4468), +20 dBm | ITX_+20 | 68.5 | 80 | mA | +20 dBm output power, square-wave match, 169 MHz, 3.3 V | 4 | |
| TX Mode Current (Si4468), +13 dBm | ITX_+13 | 44.5 | 60 | mA | +13 dBm output power, Class-E match, 915 MHz, 3.3 V | 4 | |
| Synthesizer Frequency Range (850-1050 MHz band) | FSYN | 850 | 1050 | MHz | 5 | ||
| Synthesizer Frequency Range (350-525 MHz band) | FSYN | 350 | 525 | MHz | 5 | ||
| Synthesizer Frequency Range (284-350 MHz band) | FSYN | 284 | 350 | MHz | 5 | ||
| Synthesizer Frequency Range (142-175 MHz band) | FSYN | 142 | 175 | MHz | 5 | ||
| RX Sensitivity 169 MHz (BER < 0.1%) | PRX_40 | -110 | -108 | dBm | 40 kbps, GFSK, BT = 0.5, f= 20 kHz | 6 | |
| RX Sensitivity 169 MHz (BER < 0.1%) | PRX_100 | -106 | -104 | dBm | 100 kbps, GFSK, BT = 0.5, f= 50 kHz | 6 | |
| RX Sensitivity 169 MHz (BER < 0.1%) | PRX_500 | -98 | -96 | dBm | 500 kbps, GFSK, BT = 0.5, f= 250 kHz | 6 | |
| RX Sensitivity 169 MHz (BER < 0.1%) | PRX_OOK | -110 | -107 | dBm | BER < 0.1%, 4.8 kbps, 350 kHz BW, OOK, PN15 data | 6 | |
| RX Sensitivity 169 MHz (BER < 0.1%) | PRX_OOK | -103 | -100 | dBm | BER < 0.1%, 40 kbps, 350 kHz BW, OOK, PN15 data | 6 | |
| RX Sensitivity 169 MHz (BER < 0.1%) | PRX_OOK | -97 | -93 | dBm | BER < 0.1%, 120 kbps, 350 kHz BW, OOK, PN15 data | 6 | |
| RX Sensitivity 915/868 MHz (BER < 0.1%) | PRX_40 | -109 | -107 | dBm | 40 kbps, GFSK, BT = 0.5, f= 20 kHz | 7 | |
| RX Sensitivity 915/868 MHz (BER < 0.1%) | PRX_100 | -104 | -102 | dBm | 100 kbps, GFSK, BT = 0.5, f= 50 kHz | 7 | |
| RX Sensitivity 915/868 MHz (BER < 0.1%) | PRX_500 | -97 | -92 | dBm | 500 kbps, GFSK, BT = 0.5, f= 250 kHz | 7 | |
| RX Sensitivity 915/868 MHz (BER < 0.1%) | PRX_OOK | -108 | -104 | dBm | BER < 0.1%, 4.8 kbps, 350 kHz BW, OOK, PN15 data | 7 | |
| RX Sensitivity 915/868 MHz (BER < 0.1%) | PRX_OOK | -101 | -97 | dBm | BER < 0.1%, 40 kbps, 350 kHz BW, OOK, PN15 data | 7 | |
| RX Sensitivity 915/868 MHz (BER < 0.1%) | PRX_OOK | -96 | -91 | dBm | BER < 0.1%, 120 kbps, 350 kHz BW, OOK, PN15 data | 7 | |
| RX Channel Bandwidth | BW | 0.2 | 850 | kHz | 7 | ||
| 1-Ch Offset Selectivity 169 MHz | C/I1-CH | -69 | -59 | dB | Desired 3 dB above sensitivity, BER < 0.1%, CW interferer | 7 | |
| 1-Ch Offset Selectivity 450 MHz | C/I1-CH | -60 | -50 | dB | Desired 3 dB above sensitivity, BER < 0.1%, CW interferer | 7 | |
| 1-Ch Offset Selectivity 868/915 MHz | C/I1-CH | -55 | -45 | dB | Desired 3 dB above sensitivity, BER < 0.1%, CW interferer | 7 | |
| Blocking 1 MHz Offset | 1MBLOCK | -79 | -68 | dB | Desired 3 dB above sensitivity, BER = 0.1%, CW interferer | 7 | |
| Blocking 8 MHz Offset | 8MBLOCK | -86 | -75 | dB | Desired 3 dB above sensitivity, BER = 0.1%, CW interferer | 7 | |
| Image Rejection (IF = 468.75 kHz), no calibration | ImREJ | 30 | 40 | dB | No image rejection calibration; RF = 460 MHz | 8 | |
| Image Rejection (IF = 468.75 kHz), with calibration | ImREJ | 40 | 55 | dB | With image rejection calibration; RF = 460 MHz | 8 | |
| Image Rejection (IF = 468.75 kHz), no calibration | ImREJ | 30 | 45 | dB | No image rejection calibration; RF = 915 MHz | 8 | |
| Image Rejection (IF = 468.75 kHz), with calibration | ImREJ | 40 | 52 | dB | With image rejection calibration; RF = 915 MHz | 8 | |
| Image Rejection (IF = 468.75 kHz), no calibration | ImREJ | 35 | 45 | dB | No image rejection calibration; RF = 169 MHz | 8 | |
| Image Rejection (IF = 468.75 kHz), with calibration | ImREJ | 45 | 60 | dB | With image rejection calibration; RF = 169 MHz | 8 | |
| (G)FSK Data Rate | DRFSK | 0.1 | 500 | kbps | 9 | ||
| 4(G)FSK Data Rate | DR4FSK | 0.2 | 1000 | kbps | 9 | ||
| OOK Data Rate | DROOK | 0.1 | 120 | kbps | 9 | ||
| Output Power Range (Si4468) | PTX68 | -20 | 20 | dBm | Typical range at 3.3 V | 9 | |
| Output Power Variation (Si4468), 915 MHz | 19 | 20 | 21 | dBm | At 20 dBm PA power setting, 915 MHz, Class E match, 3.3 V, 25 °C | 9 | |
| Output Power Variation (Si4468), 169 MHz | 18.5 | 20 | 21 | dBm | At 20 dBm PA power setting, 169 MHz, Square Wave match, 3.3 V, 25 °C | 10 | |
| TX RF Output Steps | PRF_OUT | 0.25 | 0.4 | dB | Within 6 dB of max power, switched current or CLE match | 10 | |
| TX RF Output Level Variation vs. Temperature | PRF_TEMP | 2.3 | 3 | dB | -40 to +85 C | 10 | |
| TX RF Output Level Variation vs. Frequency | PRF_FREQ | 0.6 | 1.7 | dB | Measured across 902-928 MHz | 10 | |
| Microcontroller Clock Output Frequency Range | FMC | 32.768 | kHz | Configurable to Fxtal or Fxtal divided by 2, 3, 7.5, 10, 15, or 30; 32.768 kHz also supported | 11 | ||
| XTAL Range | XTALRange | 25 | 32 | MHz | 11 | ||
| POR Reset Time | tPOR | 6 | ms | 11 | |||
| Input Current | IIN | -1 | 1 | µA | 0<VIN< VDD | 12 | |
| Input Current If Pullup is Activated | IINP | 1 | 4 | µA | VIL = 0 V | 12 | |
| Operating Ambient Temperature Range | TA | -40 | 125 | °C | 13 | ||
| Thermal Impedance Junction to Ambient | JA | 25 | °C/w | Based on RF evaluation board measurements | 13 | ||
| Junction Temperature Maximum Value | Tj | 137 | °C | Based on RF evaluation board measurements | 13 | ||
| Storage Temperature Range | TSTG | -55 | 150 | °C | 13 | ||
| VDD to GND | VDD | -0.3 | 3.8 | V | 13 | ||
| Instantaneous VRF-peak to GND on TX Output Pin | VRF-peak | -0.3 | 8 | V | 13 | ||
| Sustained VRF-peak to GND on TX Output Pin | VRF-peak | -0.3 | 6.5 | V | 13 | ||
| Voltage on Analog Inputs | -0.7 | V | 13 | ||||
| RX Input Power | 10 | dBm | 13 |
CAD (KiCad official)
- Symbol:
SI4468-A2A-IMR - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
si4468-a2a-imr-etched.step/si4468-a2a-imr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si4468-a2a-imr.step/si4468-a2a-imr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (57 pp, sha256
e717e10d43adad92, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).