3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSCT2601TVBR
SCT · DC-DC Converters · TSOT-23-6
SCT2601TVBR from SCT, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Bootstrap supply for the high-side MOSFET gate driver. Connect a 0.1 µF capacitor from BST to SW; the bootstrap capacitor is charged when SW is low. BST-SW absolute max 6 V; BOOT-SW UVLO ~2.2 V typical. |
| 2 | GND | power_in | Device ground return. |
| 3 | FB | input | Buck converter output feedback sensing input. Connect a resistor divider from VOUT to FB to set the output voltage; the device regulates FB to the internal 0.765 V reference (±2.5%). |
| 4 | EN | input | Enable input with an internal pull-up current source (1 µA at 1 V, 4 µA at 1.5 V). Pull below 1.13 V to disable the converter; float or tie to VIN to enable. A resistor divider from VIN to GND at EN can program the input UVLO threshold; enable high threshold ~1.223 V typ, hysteresis ~93 mV. |
| 5 | VIN | power_in | Input supply voltage, 4.5 V to 60 V (65 V absolute max). Connect a local bypass capacitor from VIN to GND. Internal VIN UVLO ~4.23 V rising with 200 mV hysteresis. |
| 6 | SW | power_out | Switching node output from the internal high-side MOSFET (500 mΩ typ, 1.6 A typ peak current limit). Connect to the external power inductor of the buck converter. Absolute max -1 V to 65 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SCT |
| Package | TSOT-23-6 |
| Category | PMIC |
| Pins | 6 |
Ordering variants
Same part, different packaging or reel option.
SCT2601TVBR
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN pins voltage | VIN, EN | -0.3 | 65 | V | 2 | ||
| BST pin voltage | BST | -0.3 | 72 | V | 2 | ||
| SW pin voltage | SW | -1 | 65 | V | 2 | ||
| BST-SW voltage | BST-SW | -0.3 | 6 | V | 2 | ||
| FB pin voltage | FB | -0.3 | 6 | V | 2 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 2 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 2 | ||
| Input voltage range | VIN | 4.5 | 60 | V | 3 | ||
| Output voltage range | VOUT | 0.765 | 57 | V | 3 | ||
| Operating junction temperature (recommended) | TJ | -40 | 150 | °C | 3 | ||
| Operating input voltage | VIN | 4.5 | 60 | V | 4 | ||
| Input UVLO threshold | VIN_UVLO | 4.23 | 4.45 | V | VIN rising | 4 | |
| Shutdown current from VIN pin | ISHDN | 1.65 | 5 | μA | EN=0, no load | 4 | |
| Reference voltage of FB | VREF | 0.746 | 0.765 | 0.784 | V | 4 | |
| High-side power MOSFET peak current limit threshold | ILIM_HS | 1.1 | 1.6 | 2 | A | 4 | |
| Enable high threshold | VEN_H | 1.223 | 1.4 | V | 4 | ||
| Enable low threshold | VEN_L | 0.9 | 1.13 | V | 4 | ||
| Switching frequency | FSW | 574 | 700 | 826 | kHz | 4 | |
| Quiescent current from VIN pin | IQ | 80 | μA | EN floating, no load, non-switching | 4 | ||
| High-side MOSFET on-resistance | RDSON_H | 500 | mΩ | VBOOT-VSW=5V | 4 | ||
| Input UVLO hysteresis | 200 | mV | 4 | ||||
| Enable threshold hysteresis | VEN_HYS | 93 | mV | 4 | |||
| Enable pin pull-up current | IEN_L | 1 | μA | EN=1V | 4 | ||
| Enable pin pull-up current | IEN_H | 4 | uA | EN=1.5V | 4 | ||
| Soft start time | TSS | 6 | ms | 4 | |||
| Minimum on-time | tON_MIN | 80 | ns | VIN=12V | 4 | ||
| Feedback overvoltage threshold (rising) | VOVP | 110 | % | VFB/VREF rising | 4 | ||
| Feedback overvoltage threshold (falling) | VOVP | 105 | % | VFB/VREF falling | 4 | ||
| BOOT-SW UVLO threshold | VBOOTUV | 2.2 | V | BOOT-SW falling | 4 | ||
| BOOT-SW UVLO hysteresis | 250 | mV | 4 | ||||
| Thermal shutdown threshold | TSD | 173 | °C | TJ rising | 4 | ||
| Thermal shutdown hysteresis | 10 | °C | 4 | ||||
| Junction to ambient thermal resistance | RθJA | 102 | °C/W | 3 | |||
| Junction to case thermal resistance | RθJC | 36.9 | °C/W | 3 |
CAD (KiCad official)
- Symbol:
SCT2601TVBR - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: TSOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
sct2601tvbr-etched.step/sct2601tvbr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sct2601tvbr.step/sct2601tvbr.glbare the bare package body.
3D model downloads
Two STEP files. Same geometry, different body top:
| File | Size | Use it when |
|---|---|---|
sct2601tvbr.step |
97 KB | You want the bare part, or you mark your own boards. |
sct2601tvbr-etched.step |
2.1 MB | You want the part with SCT2601TVBR already on it. |
The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 514 faces against 117 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SCT datasheet (21 pp, sha256
e0cf9f672262043a, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).