Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT1910IS8#TRPBF

Analog Devices · Gate Drive ICs · SO-8

LT1910IS8#TRPBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Common ground reference for the device; the datasheet specifies a 60V maximum between V+ and GND and a -15V minimum supply rating.
2 TIMER passive A timing capacitor CT from this pin to ground sets the autorestart period; after an overcurrent the pin discharges to below 1V, then recharges by a 14µA nominal source to the 2.9V timer threshold, and clamps at 3.5V nominal during normal operation.
3 FAULT output Open-collector output that pulls active LOW when TIMER falls below 3.3V at the onset of a current-limit condition, requires an external pull-up with no more than 1mA pull-up current at low status, and is rated to 36V absolute maximum.
4 IN input TTL/CMOS-compatible gate enable input with about 200mV of hysteresis that turns the charge pump on above 2V, can be driven up to 15V regardless of supply state, and is pulled below 0.8V by an internal 75k resistor if left open.
5 GATE output Drives the external N-channel MOSFET gate, pumped about 12V above the supply when IN is above 2V and pulled LOW when TIMER falls below 2.9V; absolute maximum voltage is 75V.
6 SENSE input Input to the supply-referenced current-sense comparator, which trips at a 65mV nominal offset below supply to turn the gate off; a maximum of 10kΩ may be inserted in series with the drain-sense resistor, and it is tied to supply when current sensing is not used (absolute maximum V+ ±5V).
7 NC unconnected Marked NC (no connection) in the pin configuration of the datasheet.
8 V+ power_in Supply pin for operating current and Kelvin reference for the current-sense comparator; operates from 8V to 48V (absolute maximum -15V to 60V) and must connect directly to the positive side of the drain-sense resistor.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package SO-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Current (Off State) IS 1.2 1.9 2.5 mA V+ = 48V, VIN = 0.8V 2
Delta Supply Current (On State) ∆IS(ON) 0.8 1.2 mA VIN = 2V, Measure Increase in IS 2
Input High Voltage (I-Grade) VINH 3.5 V I-Grade; l = full operating temperature range 2
Input Low Voltage (I-Grade) VINL 0.7 V I-Grade; l = full operating temperature range 2
Input Current IIN 15 30 50 µA VIN = 2V; l 2
Input Current IIN 55 110 185 µA VIN = 5V; l 2
Timer Threshold Voltage VT(TH) 2.6 2.9 3.2 V VIN = 2V, Adjust VT; l 2
Timer Clamp Voltage VT(CL) 3.2 3.5 3.8 V VIN = 0.8V 2
Timer Charge Current IT 9 14 20 µA VIN = VT = 2V 2
Drain-Sense Threshold Voltage VSENSE 50 65 80 mV 2
Drain Sense Input Current ISENSE 0.5 1.5 µA V+ = 48V, VSENSE = 65mV 3
Gate Voltage Above Supply VGATE, V+ 4 4.5 6 V V+ = 8V 3
Gate Voltage Above Supply VGATE, V+ 7 8.5 10 V V+ = 12V; l 3
Gate Voltage Above Supply (I-Grade) VGATE, V+ 10 12 15 V V+ = 24V, I-Grade; l 3
FAULT Output High Threshold Voltage VF(TH) 3.1 3.4 3.7 V VIN = 2V, IF = 1mA, Adjust VT 3
FAULT Output Low Threshold Voltage 3 3.3 3.6 V VIN = 2V, IF = 1mA, Adjust VT 3
FAULT Output Low Voltage VFOL 0.07 0.4 V IF = 1mA; l 3
Turn-On Time tON 100 220 400 µs V+ = 24V, VGATE = 32V, CGATE = 1nF 3
Turn-Off Time tOFF 25 100 µs V+ = 24V, VGATE = 2V, CGATE = 1nF 3
Current Limit Turn-Off Time tOFF(CL) 20 50 µs V+ = 24V, (V+, VSENSE)→0.1V, CGATE = 1nF 3
Supply Voltage (Pin 8) -15 60 V Pin 8 (V+) 2
Input Voltage (Pin 4) 15 V Minimum printed as (GND, 0.3V) 2
GATE Voltage (Pin 5) 75 V Pin 5 2
SENSE Voltage (Pin 6) -5 5 V V+ ±5V, relative to V+ (Pin 8) 2
FAULT Voltage (Pin 3) 36 V Pin 3 2
Current (Pins 1, 2, 4, 5, 6, 8) 40 mA Pins 1, 2, 4, 5, 6, 8 2
Operating Temperature Range (LT1910I) -40 125 °C LT1910I grade 2
Junction Temperature Range TJ -40 125 °C 2
Storage Temperature Range -65 150 °C 2
Lead Temperature (Soldering) 300 °C 10 sec soldering 2
Maximum Junction Temperature TJMAX 125 °C 2
Thermal Resistance, Junction to Ambient θJA 150 °C/W S8 package 2
Power Supply Range V+ 8 48 V Power Supply Range (Features) 1

CAD (KiCad official)

  • Symbol: LT1910IS8#TRPBF
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SO-8 (KiCad packages3D, STEP)
  • 3D model files: lt1910is8-trpbf-etched.step / lt1910is8-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt1910is8-trpbf.step / lt1910is8-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (14 pp, sha256 35b4692283783a2f, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF