Generated by kicad-footprint-generator · KiCad file format 20260206
LT1910IS8#TRPBF
Analog Devices · Gate Drive ICs · SO-8
LT1910IS8#TRPBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Common ground reference for the device; the datasheet specifies a 60V maximum between V+ and GND and a -15V minimum supply rating. |
| 2 | TIMER | passive | A timing capacitor CT from this pin to ground sets the autorestart period; after an overcurrent the pin discharges to below 1V, then recharges by a 14µA nominal source to the 2.9V timer threshold, and clamps at 3.5V nominal during normal operation. |
| 3 | FAULT | output | Open-collector output that pulls active LOW when TIMER falls below 3.3V at the onset of a current-limit condition, requires an external pull-up with no more than 1mA pull-up current at low status, and is rated to 36V absolute maximum. |
| 4 | IN | input | TTL/CMOS-compatible gate enable input with about 200mV of hysteresis that turns the charge pump on above 2V, can be driven up to 15V regardless of supply state, and is pulled below 0.8V by an internal 75k resistor if left open. |
| 5 | GATE | output | Drives the external N-channel MOSFET gate, pumped about 12V above the supply when IN is above 2V and pulled LOW when TIMER falls below 2.9V; absolute maximum voltage is 75V. |
| 6 | SENSE | input | Input to the supply-referenced current-sense comparator, which trips at a 65mV nominal offset below supply to turn the gate off; a maximum of 10kΩ may be inserted in series with the drain-sense resistor, and it is tied to supply when current sensing is not used (absolute maximum V+ ±5V). |
| 7 | NC | unconnected | Marked NC (no connection) in the pin configuration of the datasheet. |
| 8 | V+ | power_in | Supply pin for operating current and Kelvin reference for the current-sense comparator; operates from 8V to 48V (absolute maximum -15V to 60V) and must connect directly to the positive side of the drain-sense resistor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Current (Off State) | IS | 1.2 | 1.9 | 2.5 | mA | V+ = 48V, VIN = 0.8V | 2 |
| Delta Supply Current (On State) | ∆IS(ON) | 0.8 | 1.2 | mA | VIN = 2V, Measure Increase in IS | 2 | |
| Input High Voltage (I-Grade) | VINH | 3.5 | V | I-Grade; l = full operating temperature range | 2 | ||
| Input Low Voltage (I-Grade) | VINL | 0.7 | V | I-Grade; l = full operating temperature range | 2 | ||
| Input Current | IIN | 15 | 30 | 50 | µA | VIN = 2V; l | 2 |
| Input Current | IIN | 55 | 110 | 185 | µA | VIN = 5V; l | 2 |
| Timer Threshold Voltage | VT(TH) | 2.6 | 2.9 | 3.2 | V | VIN = 2V, Adjust VT; l | 2 |
| Timer Clamp Voltage | VT(CL) | 3.2 | 3.5 | 3.8 | V | VIN = 0.8V | 2 |
| Timer Charge Current | IT | 9 | 14 | 20 | µA | VIN = VT = 2V | 2 |
| Drain-Sense Threshold Voltage | VSENSE | 50 | 65 | 80 | mV | 2 | |
| Drain Sense Input Current | ISENSE | 0.5 | 1.5 | µA | V+ = 48V, VSENSE = 65mV | 3 | |
| Gate Voltage Above Supply | VGATE, V+ | 4 | 4.5 | 6 | V | V+ = 8V | 3 |
| Gate Voltage Above Supply | VGATE, V+ | 7 | 8.5 | 10 | V | V+ = 12V; l | 3 |
| Gate Voltage Above Supply (I-Grade) | VGATE, V+ | 10 | 12 | 15 | V | V+ = 24V, I-Grade; l | 3 |
| FAULT Output High Threshold Voltage | VF(TH) | 3.1 | 3.4 | 3.7 | V | VIN = 2V, IF = 1mA, Adjust VT | 3 |
| FAULT Output Low Threshold Voltage | 3 | 3.3 | 3.6 | V | VIN = 2V, IF = 1mA, Adjust VT | 3 | |
| FAULT Output Low Voltage | VFOL | 0.07 | 0.4 | V | IF = 1mA; l | 3 | |
| Turn-On Time | tON | 100 | 220 | 400 | µs | V+ = 24V, VGATE = 32V, CGATE = 1nF | 3 |
| Turn-Off Time | tOFF | 25 | 100 | µs | V+ = 24V, VGATE = 2V, CGATE = 1nF | 3 | |
| Current Limit Turn-Off Time | tOFF(CL) | 20 | 50 | µs | V+ = 24V, (V+, VSENSE)→0.1V, CGATE = 1nF | 3 | |
| Supply Voltage (Pin 8) | -15 | 60 | V | Pin 8 (V+) | 2 | ||
| Input Voltage (Pin 4) | 15 | V | Minimum printed as (GND, 0.3V) | 2 | |||
| GATE Voltage (Pin 5) | 75 | V | Pin 5 | 2 | |||
| SENSE Voltage (Pin 6) | -5 | 5 | V | V+ ±5V, relative to V+ (Pin 8) | 2 | ||
| FAULT Voltage (Pin 3) | 36 | V | Pin 3 | 2 | |||
| Current (Pins 1, 2, 4, 5, 6, 8) | 40 | mA | Pins 1, 2, 4, 5, 6, 8 | 2 | |||
| Operating Temperature Range (LT1910I) | -40 | 125 | °C | LT1910I grade | 2 | ||
| Junction Temperature Range | TJ | -40 | 125 | °C | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (Soldering) | 300 | °C | 10 sec soldering | 2 | |||
| Maximum Junction Temperature | TJMAX | 125 | °C | 2 | |||
| Thermal Resistance, Junction to Ambient | θJA | 150 | °C/W | S8 package | 2 | ||
| Power Supply Range | V+ | 8 | 48 | V | Power Supply Range (Features) | 1 |
CAD (KiCad official)
- Symbol:
LT1910IS8#TRPBF - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
lt1910is8-trpbf-etched.step/lt1910is8-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1910is8-trpbf.step/lt1910is8-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (14 pp, sha256
35b4692283783a2f, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).