3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3755EUD#PBF
Analog Devices · LED Drivers · QFN-16-EP(3x3)
LT3755EUD#PBF from Analog Devices, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VREF | power_out | Voltage reference output, typically 2V, that drives a resistor divider for the CTRL pin and can supply up to 100µA. |
| 2 | PWM | input | A low signal turns off the switcher, idles the oscillator and disconnects VC from internal loads; it has an internal pull-down resistor and should be connected to INTVCC if unused. |
| 3 | OPENLED | output | Open-collector pull-down that asserts when FB is above the FB regulation threshold minus 50mV (typ), needs an external pull-up current under 1mA, and reports an open LED fault. |
| 4 | SS | passive | Soft-start pin with a 10µA (typ) pull-up current source to an internal 2.5V rail, with the soft-start interval set by an external capacitor and reset to GND by undervoltage or thermal limit. |
| 5 | RT | passive | Switching frequency adjustment pin, set with a resistor to GND (100kHz to 1MHz), and must not be left open. |
| 6 | SHDN/UVLO | input | Shutdown and undervoltage detect pin with an accurate 1.22V falling threshold and 2.1µA pull-down for programmable hysteresis; tie to 0.4V or less to disable and reduce VIN quiescent current below 1µA. |
| 7 | INTVCC | power_out | Regulated 7.15V (typ) supply for internal loads, GATE driver and PWMOUT driver, requiring a 4.7µF bypass capacitor close to the pin and connectable directly to VIN if VIN is always 8V or less. |
| 8 | VIN | power_in | Input supply pin (4.5V to 40V operating) that must be locally bypassed with a 0.22µF or larger capacitor close to the IC. |
| 9 | SENSE | input | Current sense input for the control loop, Kelvin connected to the positive terminal of the switch current sense resistor in the NFET source. |
| 10 | GATE | output | N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states. |
| 11 | PWMOUT | output | Buffered PWM signal, driven from INTVCC, for driving an LED load disconnect NMOS or level shift, which also toggles when FB exceeds VFB plus 60mV (typ) for overvoltage protection. |
| 12 | FB | input | Voltage loop feedback pin regulating to 1.25V (nominal) for constant-voltage regulation and open LED detection; do not leave open, connect to GND if unused. |
| 13 | ISN | input | Negative terminal of the LED current feedback resistor, with ILED = 100mV/RLED for VCTRL > 1.2V when ISN is above 2.9V, and short-circuit protection input below 3V that forces GATE to 0V if ISP exceeds ISN by more than 150mV (typ). |
| 14 | ISP | input | Positive terminal of the LED current feedback resistor, with input bias current dependent on CTRL voltage and short-circuit protection input when ISN is below 3V. |
| 15 | VC | output | Transconductance error amplifier output used to stabilize the voltage loop with an RC network to GND; high impedance when PWM is low to store the demand current state. |
| 16 | CTRL | input | Current sense threshold adjustment pin where the V(ISP-ISN) threshold is 1/10th VCTRL plus an offset for 0V to 1V and constant at the 100mV full-scale value above 1.2V; do not leave open. |
| 17 | GND | power_in | Exposed pad ground that also serves as the current sense input for the negative terminal of the current sense resistor and must be soldered directly to the ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-16-EP(3x3) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Minimum Operating Voltage | VIN | 4.5 | V | VIN Tied to INTVCC | 3 | ||
| VIN Shutdown IQ | IQ | 0.1 | 1 | µA | SHDN/UVLO = 0V, PWM = 0V | 3 | |
| VIN Shutdown IQ | IQ | 5 | µA | SHDN/UVLO = 1.15V, PWM = 0V | 3 | ||
| VIN Operating IQ (Not Switching) | IQ | 1.4 | 1.7 | mA | PWM = 0V | 3 | |
| VREF Voltage | VREF | 1.965 | 2 | 2.045 | V | 100µA ≤ IVREF ≤ 0µA (E, I, H-Grades) | 3 |
| VREF Line Regulation | 0.006 | %/V | 4.5V ≤ VIN ≤ 40V | 3 | |||
| SENSE Current Limit Threshold | 98 | 108 | 118 | mV | 3 | ||
| SENSE Input Bias Current | 40 | µA | Current Out of Pin | 3 | |||
| SS Pull-Up Current | 8 | 10 | 13 | µA | Current Out of Pin | 3 | |
| ISP/ISN Full-Scale Current Sense Threshold | 96 | 100 | 103 | mV | FB = 0V, ISP = 48V | 3 | |
| ISP/ISN Full-Scale Current Sense Threshold at CTRL = 0V | -12 | -9.5 | -7 | mV | CTRL = 0V, FB = 0V, ISP = 48V | 3 | |
| CTRL Pin Range for Current Sense Threshold Adjustment | 0 | 1.1 | V | 3 | |||
| CTRL Input Bias Current | 50 | 100 | nA | Current Out of Pin | 3 | ||
| LED Current Sense Amplifier Input Common Mode Range | VISN | 2.9 | 75 | V | 3 | ||
| ISP/ISN Short-Circuit Threshold | 115 | 150 | 200 | mV | ISN = 0V | 3 | |
| ISP/ISN Short-Circuit Fault Sensing Common Mode Range | VISN | 0 | 3 | V | 3 | ||
| ISP/ISN Input Bias Current (Combined) | 55 | µA | PWM = 5V (Active), ISP = ISN = 48V | 3 | |||
| ISP/ISN Input Bias Current (Combined) | 0 | 0.1 | µA | PWM = 0V (Standby), ISP = ISN = 48V | 3 | ||
| LED Current Sense Amplifier gm | gm | 120 | µS | V(ISP, ISN) = 100mV | 4 | ||
| VC Output Impedance | 15000 | kΩ | 1V < VC < 2V | 4 | |||
| VC Standby Input Bias Current | -20 | 20 | nA | PWM = 0V | 4 | ||
| FB Regulation Voltage | VFB | 1.232 | 1.25 | 1.265 | V | ISP = ISN | 4 |
| FB Amplifier gm | 480 | µS | FB = VFB, ISP = ISN | 4 | |||
| FB Pin Input Bias Current | 40 | 100 | nA | Current Out of Pin | 4 | ||
| VC Current Mode Gain | ΔVVC/ΔVSENSE | 4 | V/V | 4 | |||
| Switching Frequency | 90 | 100 | 125 | kHz | RT = 100k | 4 | |
| Switching Frequency | 925 | 1000 | 1050 | kHz | RT = 10k | 4 | |
| Minimum Off-Time | 170 | ns | 4 | ||||
| INTVCC Regulation Voltage | 7 | 7.15 | 7.3 | V | 4 | ||
| Dropout (VIN, INTVCC) | 350 | mV | IINTVCC = -10mA, VIN = 7V | 4 | |||
| INTVCC Undervoltage Lockout | 3.9 | 4.1 | 4.3 | V | 4 | ||
| INTVCC Current Limit | 29 | 34 | 40 | mA | 4 | ||
| INTVCC Current in Shutdown | 8 | 12 | µA | SHDN/UVLO = 0V, INTVCC = 7V | 4 | ||
| PWM Input High Voltage | 1.5 | V | 4 | ||||
| PWM Input Low Voltage | 0.4 | V | 4 | ||||
| PWM Pin Resistance to GND | 45 | 60 | kΩ | 4 | |||
| PWMOUT Output Low (VOL) | VOL | 0 | 50 | mV | 4 | ||
| SHDN/UVLO Threshold Voltage Falling | 1.185 | 1.22 | 1.245 | V | E-, I-Grades | 4 | |
| SHDN/UVLO Rising Hysteresis | 20 | mV | 4 | ||||
| SHDN/UVLO Input Low Voltage | 0.4 | V | IVIN Drops Below 1µA | 4 | |||
| SHDN/UVLO Pin Bias Current Low | 1.7 | 2.05 | 2.5 | µA | SHDN/UVLO = 1.15V | 4 | |
| SHDN/UVLO Pin Bias Current High | 10 | 100 | nA | SHDN/UVLO = 1.30V | 4 | ||
| OPENLED Output Low (VOL) | VOL | 200 | mV | IOPENLED = 0.5mA (LT3755 and LT3755-2) | 4 | ||
| GATE Driver Output Rise Time | tr | 35 | ns | CL = 3300pF | 5 | ||
| GATE Driver Output Fall Time | tf | 35 | ns | CL = 3300pF | 5 | ||
| GATE Output Low (VOL) | VOL | 0.05 | V | 5 | |||
| VIN maximum | VIN | 40 | V | 2 | |||
| SHDN/UVLO maximum | SHDN/UVLO | 40 | V | Note 3 | 2 | ||
| ISP, ISN maximum | ISP, ISN | 75 | V | 2 | |||
| INTVCC maximum | INTVCC | 8 | V | VIN + 0.3V, 8V | 2 | ||
| GATE, PWMOUT maximum | 0.3 | V | INTVCC + 0.3V (Note 4); max given as offset above INTVCC | 2 | |||
| CTRL, PWM, OPENLED maximum | 12 | V | 2 | ||||
| VC, VREF, SS, FB maximum | 3 | V | 2 | ||||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | LT3755E (Notes 2, 5) | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Junction-to-Ambient Thermal Resistance | θJA | 68 | °C/W | UD package, TJMAX = 125°C | 2 | ||
| Junction-to-Case Thermal Resistance | θJC | 4.2 | °C/W | UD package | 2 |
CAD (KiCad official)
- Symbol:
LT3755EUD#PBF - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt3755eud-pbf-etched.step/lt3755eud-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3755eud-pbf.step/lt3755eud-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
ba2dd4c41f3d59ab, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).