Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3755EUD#PBF

Analog Devices · LED Drivers · QFN-16-EP(3x3)

LT3755EUD#PBF from Analog Devices, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VREF power_out Voltage reference output, typically 2V, that drives a resistor divider for the CTRL pin and can supply up to 100µA.
2 PWM input A low signal turns off the switcher, idles the oscillator and disconnects VC from internal loads; it has an internal pull-down resistor and should be connected to INTVCC if unused.
3 OPENLED output Open-collector pull-down that asserts when FB is above the FB regulation threshold minus 50mV (typ), needs an external pull-up current under 1mA, and reports an open LED fault.
4 SS passive Soft-start pin with a 10µA (typ) pull-up current source to an internal 2.5V rail, with the soft-start interval set by an external capacitor and reset to GND by undervoltage or thermal limit.
5 RT passive Switching frequency adjustment pin, set with a resistor to GND (100kHz to 1MHz), and must not be left open.
6 SHDN/UVLO input Shutdown and undervoltage detect pin with an accurate 1.22V falling threshold and 2.1µA pull-down for programmable hysteresis; tie to 0.4V or less to disable and reduce VIN quiescent current below 1µA.
7 INTVCC power_out Regulated 7.15V (typ) supply for internal loads, GATE driver and PWMOUT driver, requiring a 4.7µF bypass capacitor close to the pin and connectable directly to VIN if VIN is always 8V or less.
8 VIN power_in Input supply pin (4.5V to 40V operating) that must be locally bypassed with a 0.22µF or larger capacitor close to the IC.
9 SENSE input Current sense input for the control loop, Kelvin connected to the positive terminal of the switch current sense resistor in the NFET source.
10 GATE output N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states.
11 PWMOUT output Buffered PWM signal, driven from INTVCC, for driving an LED load disconnect NMOS or level shift, which also toggles when FB exceeds VFB plus 60mV (typ) for overvoltage protection.
12 FB input Voltage loop feedback pin regulating to 1.25V (nominal) for constant-voltage regulation and open LED detection; do not leave open, connect to GND if unused.
13 ISN input Negative terminal of the LED current feedback resistor, with ILED = 100mV/RLED for VCTRL > 1.2V when ISN is above 2.9V, and short-circuit protection input below 3V that forces GATE to 0V if ISP exceeds ISN by more than 150mV (typ).
14 ISP input Positive terminal of the LED current feedback resistor, with input bias current dependent on CTRL voltage and short-circuit protection input when ISN is below 3V.
15 VC output Transconductance error amplifier output used to stabilize the voltage loop with an RC network to GND; high impedance when PWM is low to store the demand current state.
16 CTRL input Current sense threshold adjustment pin where the V(ISP-ISN) threshold is 1/10th VCTRL plus an offset for 0V to 1V and constant at the 100mV full-scale value above 1.2V; do not leave open.
17 GND power_in Exposed pad ground that also serves as the current sense input for the negative terminal of the current sense resistor and must be soldered directly to the ground plane.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package QFN-16-EP(3x3)
Category Display Modules / LED Drivers / Display Drivers
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Minimum Operating Voltage VIN 4.5 V VIN Tied to INTVCC 3
VIN Shutdown IQ IQ 0.1 1 µA SHDN/UVLO = 0V, PWM = 0V 3
VIN Shutdown IQ IQ 5 µA SHDN/UVLO = 1.15V, PWM = 0V 3
VIN Operating IQ (Not Switching) IQ 1.4 1.7 mA PWM = 0V 3
VREF Voltage VREF 1.965 2 2.045 V 100µA ≤ IVREF ≤ 0µA (E, I, H-Grades) 3
VREF Line Regulation 0.006 %/V 4.5V ≤ VIN ≤ 40V 3
SENSE Current Limit Threshold 98 108 118 mV 3
SENSE Input Bias Current 40 µA Current Out of Pin 3
SS Pull-Up Current 8 10 13 µA Current Out of Pin 3
ISP/ISN Full-Scale Current Sense Threshold 96 100 103 mV FB = 0V, ISP = 48V 3
ISP/ISN Full-Scale Current Sense Threshold at CTRL = 0V -12 -9.5 -7 mV CTRL = 0V, FB = 0V, ISP = 48V 3
CTRL Pin Range for Current Sense Threshold Adjustment 0 1.1 V 3
CTRL Input Bias Current 50 100 nA Current Out of Pin 3
LED Current Sense Amplifier Input Common Mode Range VISN 2.9 75 V 3
ISP/ISN Short-Circuit Threshold 115 150 200 mV ISN = 0V 3
ISP/ISN Short-Circuit Fault Sensing Common Mode Range VISN 0 3 V 3
ISP/ISN Input Bias Current (Combined) 55 µA PWM = 5V (Active), ISP = ISN = 48V 3
ISP/ISN Input Bias Current (Combined) 0 0.1 µA PWM = 0V (Standby), ISP = ISN = 48V 3
LED Current Sense Amplifier gm gm 120 µS V(ISP, ISN) = 100mV 4
VC Output Impedance 15000 kΩ 1V < VC < 2V 4
VC Standby Input Bias Current -20 20 nA PWM = 0V 4
FB Regulation Voltage VFB 1.232 1.25 1.265 V ISP = ISN 4
FB Amplifier gm 480 µS FB = VFB, ISP = ISN 4
FB Pin Input Bias Current 40 100 nA Current Out of Pin 4
VC Current Mode Gain ΔVVC/ΔVSENSE 4 V/V 4
Switching Frequency 90 100 125 kHz RT = 100k 4
Switching Frequency 925 1000 1050 kHz RT = 10k 4
Minimum Off-Time 170 ns 4
INTVCC Regulation Voltage 7 7.15 7.3 V 4
Dropout (VIN, INTVCC) 350 mV IINTVCC = -10mA, VIN = 7V 4
INTVCC Undervoltage Lockout 3.9 4.1 4.3 V 4
INTVCC Current Limit 29 34 40 mA 4
INTVCC Current in Shutdown 8 12 µA SHDN/UVLO = 0V, INTVCC = 7V 4
PWM Input High Voltage 1.5 V 4
PWM Input Low Voltage 0.4 V 4
PWM Pin Resistance to GND 45 60 kΩ 4
PWMOUT Output Low (VOL) VOL 0 50 mV 4
SHDN/UVLO Threshold Voltage Falling 1.185 1.22 1.245 V E-, I-Grades 4
SHDN/UVLO Rising Hysteresis 20 mV 4
SHDN/UVLO Input Low Voltage 0.4 V IVIN Drops Below 1µA 4
SHDN/UVLO Pin Bias Current Low 1.7 2.05 2.5 µA SHDN/UVLO = 1.15V 4
SHDN/UVLO Pin Bias Current High 10 100 nA SHDN/UVLO = 1.30V 4
OPENLED Output Low (VOL) VOL 200 mV IOPENLED = 0.5mA (LT3755 and LT3755-2) 4
GATE Driver Output Rise Time tr 35 ns CL = 3300pF 5
GATE Driver Output Fall Time tf 35 ns CL = 3300pF 5
GATE Output Low (VOL) VOL 0.05 V 5
VIN maximum VIN 40 V 2
SHDN/UVLO maximum SHDN/UVLO 40 V Note 3 2
ISP, ISN maximum ISP, ISN 75 V 2
INTVCC maximum INTVCC 8 V VIN + 0.3V, 8V 2
GATE, PWMOUT maximum 0.3 V INTVCC + 0.3V (Note 4); max given as offset above INTVCC 2
CTRL, PWM, OPENLED maximum 12 V 2
VC, VREF, SS, FB maximum 3 V 2
Operating Junction Temperature Range TJ -40 125 °C LT3755E (Notes 2, 5) 2
Storage Temperature Range TSTG -65 150 °C 2
Junction-to-Ambient Thermal Resistance θJA 68 °C/W UD package, TJMAX = 125°C 2
Junction-to-Case Thermal Resistance θJC 4.2 °C/W UD package 2

CAD (KiCad official)

  • Symbol: LT3755EUD#PBF
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: lt3755eud-pbf-etched.step / lt3755eud-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3755eud-pbf.step / lt3755eud-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (28 pp, sha256 ba2dd4c41f3d59ab, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF