Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

L8211L-R20-R

UTC(Unisonic Tech) · Gate Drive ICs · SSOP-20-150mil

L8211L-R20-R from UTC(Unisonic Tech), in a SSOP-20-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 G1 output Gate drive output for FET 1, with the output gate voltage limits given in the gate characteristics table.
2 D1 output Drain connection to FET 1, which is biased to a drain current of 10mA set by RCAL.
3 G2 output Gate drive output for FET 2, with the output gate voltage limits given in the gate characteristics table.
4 D2 output Drain connection to FET 2, which is biased to a drain current of 10mA set by RCAL.
5 G3 output Gate drive output for FET 3, with the output gate voltage limits given in the gate characteristics table.
6 D3 output Drain connection to FET 3, which is biased to a drain current of 10mA set by RCAL.
7 GND power_in Ground reference for the device.
8 CNB1 passive Connect a 47nF capacitor between CNB1 and CNB2.
9 CNB2 passive Connect a 47nF capacitor between CNB2 and CNB1.
10 N/C unconnected No connection; leave this pin unconnected.
11 CSUB passive Connect an external 47nF capacitor to the -3V substrate voltage.
12 LB output Low band switch output; its low and high levels depend on LOV, with output low at -2.75V typical and output high at 3V typical when enabled.
13 HB output High band switch output; its low and high levels depend on LOV, with output low at -2.75V typical and output high at 3V typical when enabled.
14 LOV input Controls the LB and HB switch outputs, with a voltage range of -0.5V to VCC-1.8V at 50mA load.
15 FOUT output Filter output of the 22kHz tone detection filter amplifier, with output voltage of 1.95V typical at RF1=150kΩ.
16 N/C unconnected No connection; leave this pin unconnected.
17 FIN input LNB input for the tone detection circuit.
18 VPOL input Polarity control input; the threshold voltage is 14.75V typical, with 25V applied via a 10kΩ resistor in the test condition.
19 RCAL passive Connect a 33kΩ resistor to set the drain currents Id1, Id2 and Id3 to 10mA.
20 VCC power_in Supply voltage, rated from -0.6V to +12V absolute maximum with 5V to 10V operating range.

Key specifications

Parameter Value
Manufacturer UTC(Unisonic Tech)
Package SSOP-20-150mil
Category Power Management ICs
Pins 20

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VCC -0.6 12 V 3
Supply Current ICC 100 mA 3
Input Voltage VIN 25 V Continuous 3
Drain Current (per FET) ID 0 15 mA set by RCAL 3
Power Dissipation PD 600 mW Ta=25°C 3
Operating Temperature TOPR -40 70 °C 3
Storage Temperature TSTG -50 85 °C 3
Supply Voltage VCC 5 10 V 3
Supply Current ICC 6 15 mA ID1 to ID3=0 3
Supply Current ICC 25 35 mA ID1 =0, ID2 to ID3=10mA,VPOL=14V 3
Supply Current ICC 16 25 mA ID1 to ID3=0,ILB=10mA 3
Substrate Voltage (Internally generated) VSUB -3.5 -3 -2.5 V ISUB =0 3
Oscillator Freq fO 200 350 800 kHz 3
Output Current Range IGO -30 2000 µA 3
Output Voltage Gate 1 Off VG1O -0.05 0 0.05 V ID1=0mA, VPOL=14V, IGO1=0µA 3
Output Voltage Gate 1 Low VG1L -2.7 -2.4 -2 V ID1=12mA, VPOL=15.5V, IGO1=-10µA 3
Output Voltage Gate 1 High VG1H 0.4 0.75 1 V ID1=8mA, VPOL=15.5V, IGO1=0µA 3
Output Voltage Gate 2 Off VG2O -0.05 0 0.05 V ID2=0mA, VPOL=15.5V, IGO2=0µA 3
Output Voltage Gate 2 Low VG2L -2.7 -2.4 -2 V ID2=12mA, VPOL=14V, IGO2=-10µA 3
Output Voltage Gate 2 High VG2H 0.4 0.75 1 V ID2=8mA, VPOL=14V, IGO2=0µA 3
Output Voltage Gate 3 Low VG3L -3.5 -2.9 -2 V ID3=12mA, IGO3=-10µA 3
Output Voltage Gate 3 High VG3H 0.4 0.75 1 V ID3=8mA, IGO3=0µA 3
Drain Current ID 8 10 12 mA 3
Drain 1 Voltage: High VD1 1.8 2 2.2 V ID1=10mA,VPOL=15.5V 3
Drain 2 Voltage: High VD2 1.8 2 2.2 V ID2=10mA,VPOL=14V 3
Drain 3 Voltage: High VD3 1.8 2 2.2 V ID3=10mA 3
Filter Amplifier Input Bias Current IB 0.02 0.07 0.25 µA RF1=150kΩ 4
Filter Amplifier Output Voltage VOUT 1.75 1.95 2.05 V RF1=150kΩ 4
Filter Amplifier Output Current IOUT 400 520 650 µA VOUT=1.96V, VFIN=2.1V 4
Rejection Frequency fR 1 7.5 kHz V(AC)IN=1V p/p sq.w 4
V Threshold FVT 100 350 mV p/p 4
Lov Bias Current ILOV 0.02 0.15 1 µA VLOV=0V 4
LB Output Low (Enable) VLBL -3.5 -2.75 -2.5 V VLOV=0V, IL=-10µA Enable 4
LB Output Low (Enable) VLBL -0.01 0 0.01 V VLOV=3V, IL=0mA Enable 4
LB Output High (Disable) VLBH -0.025 0 0.025 V VLOV=0V, IL=10 mA Disable 4
LB Output High (Disable) VLBH 2.9 3 3.1 V VLOV=3V, IL=50mA Disable 4
HB Output Low (Disable) VHBL -3.5 -2.75 -2.5 V VLOV=0V, IL=-10µA Disable 4
HB Output Low (Disable) VHBL -0.01 0 0.01 V VLOV=3V, IL=0mA Disable 4
HB Output High (Enable) VHBH -0.025 0 0.025 V VLOV=0V, IL=10mA Enable 4
HB Output High (Enable) VHBH 2.9 3 3.1 V VLOV=3V, IL=50mA Enable 4
Input Current IPOL 10 20 40 µA VPOL=25V (Applied via RPOL=10kΩ) 4
Threshold Voltage VTPOL 14 14.75 15.5 V VPOL=25V (Applied via RPOL=10kΩ) 4

CAD (KiCad official)

  • Symbol: L8211L-R20-R
  • Footprint: Package_SO:SSOP-20_3.9x8.7mm_P0.635mm
  • 3D model: SSOP-20-150mil (KiCad packages3D, STEP)
  • 3D model files: l8211l-r20-r-etched.step / l8211l-r20-r-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); l8211l-r20-r.step / l8211l-r20-r.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: UTC(Unisonic Tech) datasheet, copy hosted by LCSC (6 pp, sha256 ef56668bb0b862e4, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF