Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
L8211L-R20-R
UTC(Unisonic Tech) · Gate Drive ICs · SSOP-20-150mil
L8211L-R20-R from UTC(Unisonic Tech), in a SSOP-20-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | G1 | output | Gate drive output for FET 1, with the output gate voltage limits given in the gate characteristics table. |
| 2 | D1 | output | Drain connection to FET 1, which is biased to a drain current of 10mA set by RCAL. |
| 3 | G2 | output | Gate drive output for FET 2, with the output gate voltage limits given in the gate characteristics table. |
| 4 | D2 | output | Drain connection to FET 2, which is biased to a drain current of 10mA set by RCAL. |
| 5 | G3 | output | Gate drive output for FET 3, with the output gate voltage limits given in the gate characteristics table. |
| 6 | D3 | output | Drain connection to FET 3, which is biased to a drain current of 10mA set by RCAL. |
| 7 | GND | power_in | Ground reference for the device. |
| 8 | CNB1 | passive | Connect a 47nF capacitor between CNB1 and CNB2. |
| 9 | CNB2 | passive | Connect a 47nF capacitor between CNB2 and CNB1. |
| 10 | N/C | unconnected | No connection; leave this pin unconnected. |
| 11 | CSUB | passive | Connect an external 47nF capacitor to the -3V substrate voltage. |
| 12 | LB | output | Low band switch output; its low and high levels depend on LOV, with output low at -2.75V typical and output high at 3V typical when enabled. |
| 13 | HB | output | High band switch output; its low and high levels depend on LOV, with output low at -2.75V typical and output high at 3V typical when enabled. |
| 14 | LOV | input | Controls the LB and HB switch outputs, with a voltage range of -0.5V to VCC-1.8V at 50mA load. |
| 15 | FOUT | output | Filter output of the 22kHz tone detection filter amplifier, with output voltage of 1.95V typical at RF1=150kΩ. |
| 16 | N/C | unconnected | No connection; leave this pin unconnected. |
| 17 | FIN | input | LNB input for the tone detection circuit. |
| 18 | VPOL | input | Polarity control input; the threshold voltage is 14.75V typical, with 25V applied via a 10kΩ resistor in the test condition. |
| 19 | RCAL | passive | Connect a 33kΩ resistor to set the drain currents Id1, Id2 and Id3 to 10mA. |
| 20 | VCC | power_in | Supply voltage, rated from -0.6V to +12V absolute maximum with 5V to 10V operating range. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | UTC(Unisonic Tech) |
| Package | SSOP-20-150mil |
| Category | Power Management ICs |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | -0.6 | 12 | V | 3 | ||
| Supply Current | ICC | 100 | mA | 3 | |||
| Input Voltage | VIN | 25 | V | Continuous | 3 | ||
| Drain Current (per FET) | ID | 0 | 15 | mA | set by RCAL | 3 | |
| Power Dissipation | PD | 600 | mW | Ta=25°C | 3 | ||
| Operating Temperature | TOPR | -40 | 70 | °C | 3 | ||
| Storage Temperature | TSTG | -50 | 85 | °C | 3 | ||
| Supply Voltage | VCC | 5 | 10 | V | 3 | ||
| Supply Current | ICC | 6 | 15 | mA | ID1 to ID3=0 | 3 | |
| Supply Current | ICC | 25 | 35 | mA | ID1 =0, ID2 to ID3=10mA,VPOL=14V | 3 | |
| Supply Current | ICC | 16 | 25 | mA | ID1 to ID3=0,ILB=10mA | 3 | |
| Substrate Voltage (Internally generated) | VSUB | -3.5 | -3 | -2.5 | V | ISUB =0 | 3 |
| Oscillator Freq | fO | 200 | 350 | 800 | kHz | 3 | |
| Output Current Range | IGO | -30 | 2000 | µA | 3 | ||
| Output Voltage Gate 1 Off | VG1O | -0.05 | 0 | 0.05 | V | ID1=0mA, VPOL=14V, IGO1=0µA | 3 |
| Output Voltage Gate 1 Low | VG1L | -2.7 | -2.4 | -2 | V | ID1=12mA, VPOL=15.5V, IGO1=-10µA | 3 |
| Output Voltage Gate 1 High | VG1H | 0.4 | 0.75 | 1 | V | ID1=8mA, VPOL=15.5V, IGO1=0µA | 3 |
| Output Voltage Gate 2 Off | VG2O | -0.05 | 0 | 0.05 | V | ID2=0mA, VPOL=15.5V, IGO2=0µA | 3 |
| Output Voltage Gate 2 Low | VG2L | -2.7 | -2.4 | -2 | V | ID2=12mA, VPOL=14V, IGO2=-10µA | 3 |
| Output Voltage Gate 2 High | VG2H | 0.4 | 0.75 | 1 | V | ID2=8mA, VPOL=14V, IGO2=0µA | 3 |
| Output Voltage Gate 3 Low | VG3L | -3.5 | -2.9 | -2 | V | ID3=12mA, IGO3=-10µA | 3 |
| Output Voltage Gate 3 High | VG3H | 0.4 | 0.75 | 1 | V | ID3=8mA, IGO3=0µA | 3 |
| Drain Current | ID | 8 | 10 | 12 | mA | 3 | |
| Drain 1 Voltage: High | VD1 | 1.8 | 2 | 2.2 | V | ID1=10mA,VPOL=15.5V | 3 |
| Drain 2 Voltage: High | VD2 | 1.8 | 2 | 2.2 | V | ID2=10mA,VPOL=14V | 3 |
| Drain 3 Voltage: High | VD3 | 1.8 | 2 | 2.2 | V | ID3=10mA | 3 |
| Filter Amplifier Input Bias Current | IB | 0.02 | 0.07 | 0.25 | µA | RF1=150kΩ | 4 |
| Filter Amplifier Output Voltage | VOUT | 1.75 | 1.95 | 2.05 | V | RF1=150kΩ | 4 |
| Filter Amplifier Output Current | IOUT | 400 | 520 | 650 | µA | VOUT=1.96V, VFIN=2.1V | 4 |
| Rejection Frequency | fR | 1 | 7.5 | kHz | V(AC)IN=1V p/p sq.w | 4 | |
| V Threshold | FVT | 100 | 350 | mV p/p | 4 | ||
| Lov Bias Current | ILOV | 0.02 | 0.15 | 1 | µA | VLOV=0V | 4 |
| LB Output Low (Enable) | VLBL | -3.5 | -2.75 | -2.5 | V | VLOV=0V, IL=-10µA Enable | 4 |
| LB Output Low (Enable) | VLBL | -0.01 | 0 | 0.01 | V | VLOV=3V, IL=0mA Enable | 4 |
| LB Output High (Disable) | VLBH | -0.025 | 0 | 0.025 | V | VLOV=0V, IL=10 mA Disable | 4 |
| LB Output High (Disable) | VLBH | 2.9 | 3 | 3.1 | V | VLOV=3V, IL=50mA Disable | 4 |
| HB Output Low (Disable) | VHBL | -3.5 | -2.75 | -2.5 | V | VLOV=0V, IL=-10µA Disable | 4 |
| HB Output Low (Disable) | VHBL | -0.01 | 0 | 0.01 | V | VLOV=3V, IL=0mA Disable | 4 |
| HB Output High (Enable) | VHBH | -0.025 | 0 | 0.025 | V | VLOV=0V, IL=10mA Enable | 4 |
| HB Output High (Enable) | VHBH | 2.9 | 3 | 3.1 | V | VLOV=3V, IL=50mA Enable | 4 |
| Input Current | IPOL | 10 | 20 | 40 | µA | VPOL=25V (Applied via RPOL=10kΩ) | 4 |
| Threshold Voltage | VTPOL | 14 | 14.75 | 15.5 | V | VPOL=25V (Applied via RPOL=10kΩ) | 4 |
CAD (KiCad official)
- Symbol:
L8211L-R20-R - Footprint:
Package_SO:SSOP-20_3.9x8.7mm_P0.635mm - 3D model: SSOP-20-150mil (KiCad packages3D, STEP)
- 3D model files:
l8211l-r20-r-etched.step/l8211l-r20-r-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l8211l-r20-r.step/l8211l-r20-r.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: UTC(Unisonic Tech) datasheet, copy hosted by LCSC (6 pp, sha256
ef56668bb0b862e4, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).