3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTLV62080DSGR
Texas Instruments · DC-DC Converters · WSON-8-EP(2x2)
TLV62080DSGR from Texas Instruments, in a WSON-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Device enable logic input (absolute maximum rating −0.3 to VIN + 0.3 V); logic HIGH enables device, logic LOW disables to shutdown; must not be left floating. |
| 2 | GND | power_in | Power and signal ground (absolute maximum rating −0.3 to 7 V). |
| 3 | GND | power_in | Power and signal ground (absolute maximum rating −0.3 to 7 V). |
| 4 | FB | input | Feedback input (absolute maximum rating −0.3 to 3.6 V) for internal control loop; connect to external feedback divider to program output voltage. |
| 5 | VOS | input | Output voltage sense input (absolute maximum rating −0.3 to 7 V) for internal control loop; must be connected to output. |
| 6 | PG | tri_state | Power Good open-drain output (absolute maximum rating −0.3 to 7 V, maximum sink current 1 mA); pulled low when output voltage below regulation limits; can be left floating if not used. |
| 7 | SW | output | Switch terminal (absolute maximum rating −0.3 to VIN + 0.3 V; −3.0 to 10 V for AC transients less than 10 ns) connected to internal MOSFET switches and inductor terminal. |
| 8 | VIN | power_in | Power supply voltage input (absolute maximum rating −0.3 to 7 V; recommended operating range 2.5 to 6 V for TLV62080). |
| 9 | Thermal Pad | power_in | Exposed thermal pad connected to GND; must be soldered to achieve appropriate power dissipation and mechanical reliability. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-8-EP(2x2) |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range, TLV62080 | VIN | 2.5 | 6 | V | 6 | ||
| Input voltage range, TLV62080 (recommended operating) | VIN | 2.5 | 6 | V | 5 | ||
| Operating junction temperature (recommended) | TJ | -40 | 125 | °C | 5 | ||
| Voltage range, VIN, PG, VOS | VIN, PG, VOS | -0.3 | 7 | V | 5 | ||
| Voltage range, SW | SW | -0.3 | V | Printed max is VIN + 0.3 V | 5 | ||
| Voltage range, SW (AC, less than 10 ns) | SW | -3 | 10 | V | AC, less than 10 ns | 5 | |
| Voltage range, FB | FB | -0.3 | 3.6 | V | 5 | ||
| Voltage range, EN | EN | -0.3 | V | Printed max is VIN + 0.3 V | 5 | ||
| Power Good sink current | PG | 1 | mA | 5 | |||
| Operating junction temperature range | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 5 | ||
| Feedback regulation voltage | VFB | 0.438 | 0.45 | 0.462 | V | VIN ≥ 2.5 V and VIN ≥ VOUT + 1 V | 6 |
| Feedback input bias current | IFB | 10 | 100 | nA | VFB = 0.45 V | 6 | |
| Output voltage range | VOUT | 0.5 | 4 | V | 6 | ||
| High side FET switch current-limit, TLV62080 | ILIM | 1.6 | 2.8 | 4 | A | Rising inductor current | 6 |
| Power good threshold | VPG | -15 | -10 | -5 | % | VOUT falling referenced to VOUT nominal | 6 |
| PG leakage current | IPG,LKG | 0.01 | 0.1 | µA | VPG = 5.0 V | 6 | |
| Input leakage current (EN) | ILKG | 0.01 | 0.5 | µA | 6 | ||
| Under voltage lock out | VUVLO | 1.8 | 2 | V | Input voltage falling | 6 | |
| Quiescent current into VIN | IQ | 30 | uA | IOUT = 0 mA, Device not switching | 6 | ||
| Shutdown current into VIN | ISD | 1 | µA | EN = LOW | 6 | ||
| High level input voltage (EN) | VIH | 1 | V | 2.5 V ≤ VIN ≤ 6 V | 6 | ||
| Low level input voltage (EN) | VIL | 0.4 | V | 2.5 V ≤ VIN ≤ 6 V | 6 | ||
| Power good low level voltage | VOL | 0.3 | V | Isink = 500 µA | 6 | ||
| Power good hysteresis | 5 | % | 6 | ||||
| Output discharge resistor | RDIS | 1 | kΩ | EN = LOW, VOUT = 1.8 V | 6 | ||
| High side FET on-resistance | RDS(on) | 120 | mΩ | ISW = 500 mA | 6 | ||
| Low side FET on-resistance | RDS(on) | 90 | mΩ | ISW = 500 mA | 6 | ||
| Thermal shutdown | TJSD | 150 | °C | Temperature rising | 6 | ||
| Thermal shutdown hysteresis | 20 | °C | Temperature falling below TJSD | 6 | |||
| Under voltage lock out hysteresis | 120 | mV | Rising above VUVLO | 6 | |||
| Junction-to-ambient thermal resistance (DSG, 8 pins) | θJA | 59.7 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance (DSG, 8 pins) | θJCtop | 70.1 | °C/W | 5 | |||
| Junction-to-board thermal resistance (DSG, 8 pins) | θJB | 30.9 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance (DSG, 8 pins) | θJCbot | 8.6 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
TLV62080DSGR - Footprint:
Package_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm - 3D model: WSON-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
tlv62080dsgr-etched.step/tlv62080dsgr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tlv62080dsgr.step/tlv62080dsgr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (30 pp, sha256
58a59ba3238e22a3, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).