3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownUCD9090RGZR
Texas Instruments · DC-DC Converters · VQFN-48-EP(7x7)
UCD9090RGZR from Texas Instruments, in a VQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MON1 | input | Analog monitor input, 0 V to 2.5 V. |
| 2 | MON2 | input | Analog monitor input, 0 V to 2.5 V. |
| 3 | RESET | input | Active-low device reset input; hold low for at least 2 µs to reset the device. |
| 4 | GPIO1 | bidirectional | General-purpose discrete input-output. |
| 5 | GPIO2 | bidirectional | General-purpose discrete input-output. |
| 6 | GPIO3 | bidirectional | General-purpose discrete input-output. |
| 7 | GPIO4 | bidirectional | General-purpose discrete input-output. |
| 8 | PMBus_CLK | bidirectional | PMBus clock; must have a pullup to 3.3 V. |
| 9 | PMBus_DATA | bidirectional | PMBus data; must have a pullup to 3.3 V. |
| 10 | FPWM1/GPIO5 | bidirectional | PWM (15.259 kHz to 125 MHz) or GPIO. |
| 11 | FPWM2/GPIO6 | bidirectional | PWM (15.259 kHz to 125 MHz) or GPIO. |
| 12 | FPWM3/GPIO7 | bidirectional | PWM (15.259 kHz to 125 MHz) or GPIO. |
| 13 | FPWM4/GPIO8 | bidirectional | PWM (15.259 kHz to 125 MHz) or GPIO. |
| 14 | FPWM5/GPIO9 | bidirectional | PWM (15.259 kHz to 125 MHz) or GPIO. |
| 15 | FPWM6/GPIO10 | bidirectional | PWM (15.259 kHz to 125 MHz) or GPIO. |
| 16 | FPWM7/GPIO11 | bidirectional | PWM (15.259 kHz to 125 MHz) or GPIO. |
| 17 | FPWM8/GPIO12 | bidirectional | PWM (15.259 kHz to 125 MHz) or GPIO. |
| 18 | GPIO13 | bidirectional | General-purpose discrete input-output. |
| 19 | PMBus_ALERT | output | PMBus alert, active-low, open-drain output; must have a pullup to 3.3 V. |
| 20 | PMBus_CNTRL | input | PMBus control input. |
| 21 | GPIO14 | bidirectional | General-purpose discrete input-output. |
| 22 | PWM1/GPI1 | input | PWM (0.93 Hz to 7.8125 MHz) or general-purpose input. |
| 23 | PWM2/GPI2 | input | PWM (0.93 Hz to 7.8125 MHz) or general-purpose input. |
| 24 | GPIO15 | bidirectional | General-purpose discrete input-output. |
| 25 | GPIO16 | bidirectional | General-purpose discrete input-output. |
| 26 | GPIO17 | bidirectional | General-purpose discrete input-output. |
| 27 | TCK/GPIO18 | bidirectional | JTAG test clock or GPIO. |
| 28 | TDO/GPIO19 | bidirectional | JTAG test data out or GPIO. |
| 29 | TDI/GPIO20 | bidirectional | JTAG test data in (tie to Vdd with 10-kΩ resistor) or GPIO. |
| 30 | TMS/GPIO21 | bidirectional | JTAG test mode select (tie to Vdd with 10-kΩ resistor) or GPIO. |
| 31 | TRST | input | JTAG test reset; tie to ground with 10-kΩ resistor. |
| 32 | DVSS | power_in | Digital ground. |
| 33 | V33D | power_in | Digital core 3.3-V supply; refer to the Layout Guidelines section. |
| 34 | V33A | power_in | Analog 3.3-V supply; refer to the Layout Guidelines section. |
| 35 | BPCap | passive | 1.8-V bypass capacitor connection; refer to the Layout Guidelines section. |
| 36 | AVSS1 | power_in | Analog ground. |
| 37 | MON11 | input | Analog input, 0.2 V to 2.5 V. |
| 38 | MON3 | input | Analog monitor input, 0 V to 2.5 V. |
| 39 | MON4 | input | Analog monitor input, 0 V to 2.5 V. |
| 40 | MON5 | input | Analog monitor input, 0 V to 2.5 V. |
| 41 | MON6 | input | Analog monitor input, 0 V to 2.5 V. |
| 42 | MON7 | input | Analog monitor input, 0 V to 2.5 V. |
| 43 | PMBus_ADDR1 | input | PMBus analog address input, most-significant address bit. |
| 44 | PMBus_ADDR0 | input | PMBus analog address input, least-significant address bit. |
| 45 | MON8 | input | Analog monitor input, 0 V to 2.5 V. |
| 46 | MON9 | input | Analog monitor input, 0 V to 2.5 V. |
| 47 | AVSS2 | power_in | Analog ground. |
| 48 | MON10 | input | Analog monitor input, 0 V to 2.5 V. |
| 49 | Thermal pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-48-EP(7x7) |
| Category | Power Supply Chip |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage applied at V33D to DVSS | -0.3 | 3.8 | V | 6 | |||
| Voltage applied at V33A to AVSS | -0.3 | 3.8 | V | 6 | |||
| Voltage applied to any other pin | -0.3 | V | Printed maximum is V33A + 0.3 V (not a numeric value) | 6 | |||
| Storage temperature (Tstg) | Tstg | -55 | 150 | °C | 6 | ||
| Supply voltage during operation (V33D, V33DIO, V33A) | 3 | 3.3 | 3.6 | V | 6 | ||
| Operating free-air temperature | TA | -40 | 110 | °C | 6 | ||
| Junction temperature | TJ | 125 | °C | 6 | |||
| Analog input voltage range MON1-MON10 | VMON | 0 | 2.5 | V | MON1-MON10 | 7 | |
| Analog input voltage range MON11 | VMON | 0.2 | 2.5 | V | MON11 | 7 | |
| ADC integral nonlinearity | INL | -4 | 4 | LSB | 7 | ||
| ADC differential nonlinearity | DNL | -2 | 2 | LSB | 7 | ||
| Input leakage current | Ilkg | 100 | nA | 3 V applied to pin | 7 | ||
| Input offset current | IOFFSET | -5 | 5 | μA | 1-kΩ source impedance | 7 | |
| Input impedance MON11 | RIN | 0.5 | 1.5 | 3 | MΩ | MON11, ground reference | 7 |
| ADC 2.5 V internal reference accuracy (0°C to 125°C) | VREF | -0.5 | 0.5 | % | 0°C to 125°C | 7 | |
| ADC 2.5 V internal reference accuracy (-40°C to 125°C) | VREF | -1 | 1 | % | -40°C to 125°C | 7 | |
| Bias current for PMBus address pins | IBIAS | 9 | 11 | μA | 7 | ||
| Voltage, shorted PMBus_ADDR pin | VADDR_SHORT | 0.124 | V | PMBus_ADDR0, PMBus_ADDR1 short to ground | 7 | ||
| Low-level output voltage | VOL | 0.25 | V | IOL = 6 mA, V33DIO = 3 V; printed limit is Dgnd + 0.25 V (numeric offset shown) | 7 | ||
| High-level output voltage | VOH | 0.6 | V | IOH = -6 mA, V33DIO = 3 V; printed limit is V33DIO, 0.6 V (numeric offset shown) | 7 | ||
| High-level input voltage | VIH | 2.1 | 3.6 | V | V33DIO = 3 V | 7 | |
| Low-level input voltage | VIL | 1.4 | V | V33DIO = 3.5 V | 7 | ||
| MARGINING-PWM frequency FPWM1-8 | TPWM_FREQ | 15.26 | 125000 | kHz | FPWM1-8 | 7 | |
| MARGINING-PWM frequency PWM1-2 | TPWM_FREQ | 0.001 | 7800 | kHz | PWM1-2 | 7 | |
| MARGINING-PWM duty cycle range | DUTYPWM | 0 | 100 | % | 7 | ||
| Minimum VDD slew rate | VDDSlew | 0.25 | V/ms | VDD slew rate between 2.3 V and 2.9 V | 7 | ||
| Low-pulse duration needed at RESET pin | tRESET | 2 | μS | To reset device during normal operation | 7 | ||
| Internal oscillator frequency | f(PCLK) | 240 | 250 | 260 | MHz | TA = 125°C, TA = 25°C | 7 |
| Retention of configuration parameters | tretention | 100 | years | TJ = 25°C | 7 | ||
| Number of nonvolatile erase/write cycles | Write_Cycles | 20 | K cycles | TJ = 25°C | 7 | ||
| SMBus/PMBus operating frequency | FSMB | 10 | 400 | kHz | Slave mode, SMBC 50% duty cycle; TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | |
| I2C operating frequency | FI2C | 10 | 400 | kHz | Slave mode, SCL 50% duty cycle; TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | |
| Bus free time between start and stop | t(BUF) | 1.3 | μs | TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | ||
| Hold time after (repeated) start | t(HD:STA) | 0.6 | μs | TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | ||
| Repeated-start setup time | t(SU:STA) | 0.6 | μs | TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | ||
| Stop setup time | t(SU:STO) | 0.6 | μs | TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | ||
| Data hold time | t(HD:DAT) | 0 | ns | Receive mode; TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | ||
| Data setup time | t(SU:DAT) | 100 | ns | TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | ||
| Error signal/detect timeout | t(TIMEOUT) | 35 | ms | See (1) | 8 | ||
| Clock low period | t(LOW) | 1.3 | μs | TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | ||
| Clock high period | t(HIGH) | 0.6 | μs | See (2); TA = -40°C to 85°C, 3 V < VDD < 3.6 V | 8 | ||
| Cumulative clock low slave extend time | t(LOW:SEXT) | 25 | ms | See (3) | 8 | ||
| Clock/data fall time | tf | 300 | ns | See (4); formula printed as 20 + 0.1 Cb | 8 | ||
| Clock/data rise time | tr | 300 | ns | See (5); formula printed as 20 + 0.1 Cb | 8 | ||
| Total capacitance of one bus line | Cb | 400 | pF | 8 | |||
| Supply current V33A | IV33A | 8 | mA | VV33A = 3.3 V; typical values per note (1) | 7 | ||
| Supply current V33DIO | IV33DIO | 2 | mA | VV33DIO = 3.3 V; typical values per note (1) | 7 | ||
| Supply current V33D | IV33D | 40 | mA | VV33D = 3.3 V; typical values per note (1) | 7 | ||
| Supply current V33D while storing configuration to flash | IV33D | 50 | mA | VV33D = 3.3 V, storing configuration parameters in flash memory | 7 | ||
| Input impedance MON1-MON10 | RIN | 8 | MΩ | ground reference | 7 | ||
| Input capacitance | CIN | 10 | pF | 7 | |||
| ADC sample period | tCONVERT | 400 | μs | 12 voltages sampled, 3.89 μs/sample | 7 | ||
| Voltage, open PMBus_ADDR pin | VADDR_OPEN | 2.26 | V | PMBus_ADDR0, PMBus_ADDR1 open | 7 | ||
| Supply voltage at which device comes out of reset | VRESET | 2.4 | V | For power-on reset (POR) | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 25 | °C/W | RGZ (VQFN), 48 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 8.9 | °C/W | RGZ (VQFN), 48 pins | 6 | ||
| Junction-to-board thermal resistance | RθJB | 5.5 | °C/W | RGZ (VQFN), 48 pins | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.7 | °C/W | RGZ (VQFN), 48 pins | 6 |
CAD (KiCad official)
- Symbol:
UCD9090RGZR - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: VQFN-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
ucd9090rgzr-etched.step/ucd9090rgzr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucd9090rgzr.step/ucd9090rgzr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (57 pp, sha256
ace0eb5f3b9549f0, retrieved 2026-10-29, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).