Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MIC29151-3.3WU

Microchip Tech · Linear Voltage Regulators (LDO) · TO-263-5

MIC29151-3.3WU from Microchip Tech, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EN input CMOS/TTL compatible ON/OFF control input: logic high enables the regulator, logic low shuts it down, and it may be tied directly to 30V or below.
2 IN power_in Supplies the current to the output power device; the overvoltage sensor disables the regulator when the input voltage exceeds approximately 32V.
3 GND power_in Ground pin; the TAB is also connected internally to the IC ground.
4 OUT power_out The regulator output voltage; a minimum of 10 µF at full load is required for stability on MIC2915x fixed versions.
5 FLG output Active-low open-collector error flag that pulls low on output faults such as dropout, current limit or overtemperature (inoperative during overtemperature shutdown) and may sink 10 mA.
6 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package TO-263-5
Category Power Supply Chip
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output Voltage (tolerance, IOUT = 10 mA) VOUT -1 1 % IOUT = 10 mA 5
Output Voltage (tolerance, 10 mA to full load) VOUT -2 2 % 10 mA ≤ IOUT ≤ IFL, (VOUT + 1V) ≤ VIN ≤26V (Note 3) 5
Line Regulation 0.06 0.5 % IOUT = 10 mA, (VOUT + 1V) ≤ VIN ≤ 26V 5
Load Regulation 0.2 1 % VIN = VOUT + 1V, 10 mA ≤ IOUT ≤ 1.5A (Note 3, Note 4) 5
Output Voltage Temperature Coefficient ΔVO/ΔT 20 100 ppm/°C Output Voltage (Note 4) 5
Dropout Voltage (MIC2915x) 80 200 mV ΔVOUT = -1% (Note 5), MIC2915x IOUT = 100 mA 5
Dropout Voltage (MIC2915x) 350 600 mV ΔVOUT = -1% (Note 5), MIC2915x IOUT = 1.5A 5
Ground Current (MIC2915x) IGND 8 20 mA MIC2915x IOUT = 750 mA, VIN = VOUT + 1V 5
Current Limit (MIC2915x) ILIM 2.1 3.5 A MIC2915x, VOUT = 0V, (Note 7) 5
Ground Current in Shutdown 2 10 µA MIC29150/1/2/3 only 6
Ground Current in Shutdown 30 µA VEN = 0.4V 6
Output Low Voltage (Error Flag) VOL 220 300 mV Device set for 5V, VIN = 4.5V, IOL = 250 µA 6
Output Low Voltage (Error Flag, bold temperature range) VOL 400 mV Device set for 5V, VIN = 4.5V, IOL = 250 µA 6
Upper Threshold Voltage 40 60 mV Device set for 5V, (Note 10) 6
Upper Threshold Voltage (bold temperature range) 25 mV Device set for 5V, (Note 10) 6
Lower Threshold Voltage 75 95 mV Device set for 5V, (Note 10) 6
Lower Threshold Voltage (bold temperature range) 140 mV Device set for 5V, (Note 10) 6
Output Leakage Current (Error Flag) 0.01 1 µA VOH = 26V 6
Output Leakage Current (Error Flag, bold temperature range) 2 µA 6
Input Logic Voltage Low (OFF) 0.8 V 7
Input Logic Voltage High (ON) 2.4 V 7
Enable Pin Input Current 100 600 µA VEN = 26V 7
Enable Pin Input Current (bold temperature range) 750 µA VEN = 26V 7
Enable Pin Input Current 0.7 2 µA VEN = 0.8V 7
Enable Pin Input Current (bold temperature range) 4 µA VEN = 0.8V 7
Regulator Output Current in Shutdown 10 500 µA VEN ≤ 0.8V and VIN ≤ 26V, VOUT = 0 7
Storage Temperature Range TS -65 150 °C 8
Operating Junction Temperature TJ -40 125 °C 8
Lead Temperature 260 °C Soldering, 5 sec. 8
Thermal Resistance TO-263 Junction-to-Case θJC 2 °C/W 8
Input Supply Voltage VIN -20 60 V Note 1: 60V limited to <100 ms and duty cycle ≤1% 4
Enable Input Voltage VEN -0.3 V Upper limit printed as VIN 4
Maximum Operating Input Voltage VIN 26 V 4

CAD (KiCad official)

  • Symbol: MIC29151-3.3WU
  • Footprint: Package_TO_SOT_SMD:TO-263-5_TabPin6
  • 3D model: TO-263-5 (KiCad packages3D, STEP)
  • 3D model files: mic29151-3-3wu-etched.step / mic29151-3-3wu-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic29151-3-3wu.step / mic29151-3-3wu.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (42 pp, sha256 1c6802c39b014f5f, retrieved 2026-10-29, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF