3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMIC29151-3.3WU
Microchip Tech · Linear Voltage Regulators (LDO) · TO-263-5
MIC29151-3.3WU from Microchip Tech, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | CMOS/TTL compatible ON/OFF control input: logic high enables the regulator, logic low shuts it down, and it may be tied directly to 30V or below. |
| 2 | IN | power_in | Supplies the current to the output power device; the overvoltage sensor disables the regulator when the input voltage exceeds approximately 32V. |
| 3 | GND | power_in | Ground pin; the TAB is also connected internally to the IC ground. |
| 4 | OUT | power_out | The regulator output voltage; a minimum of 10 µF at full load is required for stability on MIC2915x fixed versions. |
| 5 | FLG | output | Active-low open-collector error flag that pulls low on output faults such as dropout, current limit or overtemperature (inoperative during overtemperature shutdown) and may sink 10 mA. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (tolerance, IOUT = 10 mA) | VOUT | -1 | 1 | % | IOUT = 10 mA | 5 | |
| Output Voltage (tolerance, 10 mA to full load) | VOUT | -2 | 2 | % | 10 mA ≤ IOUT ≤ IFL, (VOUT + 1V) ≤ VIN ≤26V (Note 3) | 5 | |
| Line Regulation | 0.06 | 0.5 | % | IOUT = 10 mA, (VOUT + 1V) ≤ VIN ≤ 26V | 5 | ||
| Load Regulation | 0.2 | 1 | % | VIN = VOUT + 1V, 10 mA ≤ IOUT ≤ 1.5A (Note 3, Note 4) | 5 | ||
| Output Voltage Temperature Coefficient | ΔVO/ΔT | 20 | 100 | ppm/°C | Output Voltage (Note 4) | 5 | |
| Dropout Voltage (MIC2915x) | 80 | 200 | mV | ΔVOUT = -1% (Note 5), MIC2915x IOUT = 100 mA | 5 | ||
| Dropout Voltage (MIC2915x) | 350 | 600 | mV | ΔVOUT = -1% (Note 5), MIC2915x IOUT = 1.5A | 5 | ||
| Ground Current (MIC2915x) | IGND | 8 | 20 | mA | MIC2915x IOUT = 750 mA, VIN = VOUT + 1V | 5 | |
| Current Limit (MIC2915x) | ILIM | 2.1 | 3.5 | A | MIC2915x, VOUT = 0V, (Note 7) | 5 | |
| Ground Current in Shutdown | 2 | 10 | µA | MIC29150/1/2/3 only | 6 | ||
| Ground Current in Shutdown | 30 | µA | VEN = 0.4V | 6 | |||
| Output Low Voltage (Error Flag) | VOL | 220 | 300 | mV | Device set for 5V, VIN = 4.5V, IOL = 250 µA | 6 | |
| Output Low Voltage (Error Flag, bold temperature range) | VOL | 400 | mV | Device set for 5V, VIN = 4.5V, IOL = 250 µA | 6 | ||
| Upper Threshold Voltage | 40 | 60 | mV | Device set for 5V, (Note 10) | 6 | ||
| Upper Threshold Voltage (bold temperature range) | 25 | mV | Device set for 5V, (Note 10) | 6 | |||
| Lower Threshold Voltage | 75 | 95 | mV | Device set for 5V, (Note 10) | 6 | ||
| Lower Threshold Voltage (bold temperature range) | 140 | mV | Device set for 5V, (Note 10) | 6 | |||
| Output Leakage Current (Error Flag) | 0.01 | 1 | µA | VOH = 26V | 6 | ||
| Output Leakage Current (Error Flag, bold temperature range) | 2 | µA | 6 | ||||
| Input Logic Voltage Low (OFF) | 0.8 | V | 7 | ||||
| Input Logic Voltage High (ON) | 2.4 | V | 7 | ||||
| Enable Pin Input Current | 100 | 600 | µA | VEN = 26V | 7 | ||
| Enable Pin Input Current (bold temperature range) | 750 | µA | VEN = 26V | 7 | |||
| Enable Pin Input Current | 0.7 | 2 | µA | VEN = 0.8V | 7 | ||
| Enable Pin Input Current (bold temperature range) | 4 | µA | VEN = 0.8V | 7 | |||
| Regulator Output Current in Shutdown | 10 | 500 | µA | VEN ≤ 0.8V and VIN ≤ 26V, VOUT = 0 | 7 | ||
| Storage Temperature Range | TS | -65 | 150 | °C | 8 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 8 | ||
| Lead Temperature | 260 | °C | Soldering, 5 sec. | 8 | |||
| Thermal Resistance TO-263 Junction-to-Case | θJC | 2 | °C/W | 8 | |||
| Input Supply Voltage | VIN | -20 | 60 | V | Note 1: 60V limited to <100 ms and duty cycle ≤1% | 4 | |
| Enable Input Voltage | VEN | -0.3 | V | Upper limit printed as VIN | 4 | ||
| Maximum Operating Input Voltage | VIN | 26 | V | 4 |
CAD (KiCad official)
- Symbol:
MIC29151-3.3WU - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
mic29151-3-3wu-etched.step/mic29151-3-3wu-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic29151-3-3wu.step/mic29151-3-3wu.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (42 pp, sha256
1c6802c39b014f5f, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).